7101L1YA3SE2 datasheet, PDF - EEWORLD Datasheet

7101L1YA3SE2: DescriptionTOGGLE SWITCH,RIGHT ANGLE,SPDT,ON-ON,R ANGLE PC TAIL TERMINAL,TOGGLE,5; CategoryMechanical and electronic products switch; File Size1MB，14 Pages; ManufacturerC&K Components; Environmental Compliance

Download Datasheet Parametric View All

7101L1YA3SE2 Overview

TOGGLE SWITCH,RIGHT ANGLE,SPDT,ON-ON,R ANGLE PC TAIL TERMINAL,TOGGLE,5

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Maker	C&K Components
Reach Compliance Code	not_compliant
ECCN code	EAR99
Actuator angle	25 deg
Actuator color	BLACK
Actuator length	0.64 inch
Actuator material	BRASS
Actuator type	TOGGLE
body width	6.858 mm
body height	12.7 mm
Body length or diameter	12.7 mm
Nozzle length	0.35 inch
Casing type	1/4-40
center contact material	COPPER ALLOY
Center contact plating	SILVER
Contact (AC) maximum rated R load	2A@250VAC
Maximum contact current (AC)	2 A
Maximum contact current (DC)	5 A
Contact (DC) maximum rated R load	5A@28VDC
Contact function	ON-ON
Contact resistance	0.01 mΩ
Maximum contact voltage (AC)	250 V
Maximum contact voltage (DC)	28 V
Dielectric withstand voltage	1400VAC V
Electrical life	100000 Cycle(s)
End contact material	COIN SILVER
End contact plating	SILVER
Shell material	STAINLESS STEEL
Insulation resistance	1000000000 Ω
JESD-609 code	e3
Manufacturer's serial number	7000
Installation features	THROUGH HOLE-RIGHT ANGLE
Maximum operating temperature	85 °C
Minimum operating temperature	-30 °C
PCB hole count	5
seal	EPOXY
Solderability	MIL-STD
surface mount	NO
switch function	SPDT
Switch type	TOGGLE SWITCH
Terminal surface	Matte Tin (Sn) - with Nickel (Ni) barrier
Terminal length	0.125 inch
Terminal material	COPPER ALLOY
Termination type	SOLDER

Resistive tap monitors and sets W-CDMA power levels: In a cell phone it''s important to set the power level of a power amplifier (PA) precisely. This is necessary to compensate for the temperature variation and to set the correct power, which is dictate...; tmily RF/Wirelessly

How to design amplifier circuits with different frequencies?: I want to design an analog amplifier circuit to achieve the same amplification factor for two input signals with different frequencies. If I use an AGC circuit to implement such an analog amplifier ci...; xxhhzz Analog electronics

DB9 pin type: RS485 output signal and terminal pin assignment: The following figure shows the DB9 pin type RS485 output signal and terminal pin assignment. This DB9 pin type is different from the standard RS232 or RS485 DB9 definition. The DB9 pin type descriptio...; 灞波儿奔 Microcontroller MCU

OFDR for short-range high-precision measurements: [i=s]This post was last edited by junnotech on 2019-2-14 11:04[/i] [align=left][size=4]OTDR (Optical Time Domain Reflectometry) and OFDR (Optical Frequency Domain Reflectometry) are two commonly used ...; junnotech Test/Measurement

FPGA instantiation issues: Dear experts, I have a question, as follows: module test（A,B,C） endmodule test t1（.A(AX),.B(BX),.C(CX)）As shown above, the test module is instantiated, but I did not give values for A, B, and C, which...; bioger EE_FPGA Learning Park

EEWORLD University ---- MSP430 capacitive touch technology - waterproof Demo: MSP430 capacitive touch technology - Waterproof Demo : https://training.eeworld.com.cn/course/5771...; hi5 MCU

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components