COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
•
•
•
•
•
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
PH1 SERIES
2
Dimensions Diagram
(Specifications in inches [mm] unless otherwise noted.)
Configuration A
0.52 MAX
[13.2]
FIBER PIGTAIL
39.37 NOM
[1 METER]
0.525±0.010
[13.34±0.25]
2.20 MAX
[56.1]
3.00 MAX
[76.5]
2X 1.20 MAX
[30.0]
Configuration C
0.52 MAX
[13.2]
2X 3.94 MAX
[100.1]
3.31 MAX
[84.1]
0.835±0.010
[21.21±0.25]
3.50 MAX
[88.9]
2X 1.10 MAX
[27.9]
FIBER PIGTAIL
41.73 NOM
[1.06 METER]
PH1 SERIES
3
Module Functional Block Diagram
1.8 V Supply Source
Configuration
Vdd2 (1.8VDC)
(K 30) TxFIFOERR
(K27) TxFIFORES
(B30) TxLOCKERR
(K24) TxRESET
TxDin (15:0)
(G28, 29) TxPICLK
(J21, K21) TxRATESEL(1: 0)
(E28, 29) TxPCLK
(C28, 29) TxMCLK
(F30) TxREFSEL
Vdd (3.3VDC)
Vcc (5VDC)
Vee ( -5.2Vdc)
Vdd2 (1.8 VDC optional)
Regulator
Vdd (3.3Vdc)
Vcc (5VDC)
Vee ( -5.2Vdc)
GND
Mux
10 Gb/s
CMU
10 Gb/s
Laser
Driver
Laser
TEC
Control
EML
Laser
Laser
Bias
Control
µC bus
10 Gb/s Serial Optic Output
LsPOWMON (D18)
LsBIASMON (F18)
LsENABLE (F21)
TxTRACE (J29)
LsTEMPMON (D21)
LsTEMPALM (F27)
LsBIASALM (F24
ALMINT (H15)
I2CDATA (K18)
I2CCLOCK (K15)
I2CADD(2:0) (D9,6,3)
MOD_RESET (D12)
(A28, 29) TxREFCLK
PLL
(H30) TxLINETIMESEL
Jitter Filter Bypass
Configuration
Transmitter
Receiver
F RAM
EEPROM
µC
RxDout (15:0)
(E13,14) RxPOCLK
(C13,14) RxMCLK
De -Mux
TIA
PD
10 Gb/s Serial Optic Input
(B 15) RxLOCKERR
(A13,14) RxREFCLK
10 Gb/s Clock
Recovery
PD Bias
Control
RxPOWMON (F3)
RxPOWALM (F6)
APDTEMPMON (H3)
(L1 version only)
(B9) RxLCKREF
(B6) RxMUTEDout
(F15) RxREFSEL
RxRATESEL(1:0) (J3,K3)
RxMUTEPOCLK (K9)
PH1 SERIES
4
PH1 (SR2) Specifications
Parameter
Transmitter
Output power (EOL)
Extinction ratio (EOL)
Tx spectral range
Sidemode suppression ratio
Spectral power density
Jitter generation
Receiver
PIN input power {BER = 10
-12
} (EOL)
Maximum overload: PIN receiver {BER = 10
-12
} (EOL)
Rx spectral range
Jitter tolerance and jitter transfer
System optical return loss
Optical Path
Optical path penalty at 1550 nm and with 1600 ps/nm dispersion
Electrical
Operating case temperature
TDM power dissipation with jitter filter
TDM power dissipation without jitter filter
Minimum
Typical
Maximum
-4 dBm
8.2 dB
1530 nm
30 dB
-
-2.5 dBm
-
-
-
-
GR-253 compliant
-16.0 dBm
-
-
GR-253 compliant
-
-
-
5.0 W
4.8 W
-1 dBm
-
1570 nm
-
0.1 mW/MHz
-15.0 dBm
-1 dBm
1280 nm
-27 dB
-
-5 °C
-
-
-
-
1600 nm
-
2 dB
70 °C
7.0 W
6.8 W
PH1 (IR2) Specifications
Parameter
Transmitter
Output power (EOL)
Extinction ratio (EOL)
Tx spectral range
Wavelength stability over operating temperature (BOL setup, 100 GHz option)
Wavelength stability over operating temperature (EOL setup, 100 GHz option)
Sidemode suppression ratio
Spectral power density
Jitter generation
Receiver
PIN input power {BER = 10
-12
} (EOL)
Maximum overload: PIN receiver {BER = 10
-12
} (EOL)
Rx spectral range
Jitter tolerance and jitter transfer
System optical return loss
Optical Path
Optical path penalty at 1550 nm and with 1600 ps/nm dispersion
Electrical
Operating case temperature
TDM power dissipation with jitter filter
TDM power dissipation without jitter filter
DWDM power dissipation with jitter filter
DWDM power dissipation without jitter filter
Minimum
Typical
Maximum
-1 dBm
8.2 dB
1530 nm
-25 pm
-100 pm
30 dB
-
0.5 dBm
-
-
-
-
-
-
GR-253 compliant
-16.0 dBm
-
-
GR-253 compliant
-
-
-
5.0 W
4.8 W
5.8 W
5.6 W
2 dBm
-
1570 nm
25 pm
100 pm
-
0.1 mW/MHz
-15.0 dBm
-1 dBm
1280 nm
-27 dB
-
-5 °C
-
-
-
-
-
-
1600 nm
-
2 dB
70 °C
7.0 W
6.8 W
7.8 W
7.6 W
PH1 SERIES
5
PH1 (LR2) Specifications
Parameter
Transmitter
Output power (EOL)
LP and LA options
LH option
Extinction ratio (EOL)
Tx spectral range
Wavelength stability over operating temperature (BOL setup, 100 GHz option)
Wavelength stability over operating temperature (EOL setup, 100 GHz option)
Sidemode suppression ratio
Spectral power density
Jitter generation
Receiver
APD input power {BER = 10
-12
} (EOL)
Maximum overload: APD receiver {BER = 10
-12
} (EOL)
Rx spectral range
Jitter tolerance and jitter transfer
System optical return loss
Optical Path
Optical path penalty at 1550 nm and with 1600 ps/nm dispersion
Electrical
Operating case temperature
TDM power dissipation with jitter filter
TDM power dissipation without jitter filter
DWDM power dissipation with jitter filter
DWDM power dissipation without jitter filter
Minimum
Typical
Maximum
0 dBm
2 dBm
9.5 dB
1530 nm
-25 pm
-100 pm
30 dB
-
2 dBm
4 dBm
-
-
-
-
-
-
GR-253 compliant
-17 dBm
-
-
GR-253 compliant
-
-
-
8.5 W
8.7 W
6.7 W
6.5 W
4 dBm
6 dBm
-
1570 nm
25 pm
100 pm
-
0.1 mW/MHz
-24 dBm
-5 dBm
1280 nm
-27 dB
-
-5 °C
-
-
-
-
-
-
1600 nm
-
2 dB
70 °C
7.9 W
7.7 W
8.7 W
8.5 W
MicroPython Open Source section
京公网安备 11010802033920号
EEWORLD
