EEWORLDEEWORLDEEWORLD

Part Number

Search

SE-K63M1000B1F11625

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 63V, 20% +Tol, 20% -Tol, 1000uF, Through Hole Mount, ROHS COMPLIANT
CategoryPassive components    capacitor   
File Size60KB,3 Pages
ManufacturerYAGEO
Websitehttp://www.yageo.com/
Environmental Compliance  
Download Datasheet Parametric View All

SE-K63M1000B1F11625 Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 63V, 20% +Tol, 20% -Tol, 1000uF, Through Hole Mount, ROHS COMPLIANT

SE-K63M1000B1F11625 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerYAGEO
package instruction,
Reach Compliance Codecompliant
ECCN codeEAR99
capacitance1000 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
dielectric materialsALUMINUM (WET)
leakage current1.27 mA
Manufacturer's serial numberSE-K
Installation featuresTHROUGH HOLE MOUNT
negative tolerance20%
Number of terminals2
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
Package shapeCYLINDRICAL PACKAGE
method of packingBULK
polarityPOLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)63 V
ripple current900 mA
surface mountNO
Delta tangent0.1
Terminal shapeWIRE
YAGEO CORPORATION
ALUMINUM ELECTROLYTIC CAPACITORS
SE-K
[ For General ]
105°C Single-Ended Lead Aluminum Electrolytic Capacitors Rated Voltage up to 450V
Miniature Size Aluminum
Electrolytic Capacitors
ELECTRICAL CHARACTERISTICS
Operating Temperature : -40° ~ +105°C / -25° ~ +105°C
Working Voltage : 6.3 ~ 250V / 350 ~ 450V
Rate Capacitance Range : 0.47 ~ 15000µF / 0.47 ~ 150µF
Capacitance Tolerance : -20 ~ +20%
DC Leakage Current (µA) : I = 0.01CV + 3 / 0.03CV + 10
( After 2 Minutes Application of DC Working Voltage at 25°C )
Dissipation Factor : at 120 Hz, 25°C
W V (V) : 6.3
10
16
25
35
50
63
80
100 160 ~ 250 350 ~ 450
D.F (%) : 26
22
18
16
14
12
10
10
10
15
20
For capacitor whose capacitance excceds 1000 µF. The value of DF(%) is increased by 2% for every
addition of 1000 µF.
Load Life : 1000 Hours at Assured with Full Rated Maximum Ripple Current Applied
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200% of Initial Requirement
(c) Leakage Current : Not Exceed the Initial Requirement
Shelf Life : 500 Hours, No Voltage Applied
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200% of Initial Requirement
(c) Leakage Current : Not Exceed 200% of Initial Requirement
DESCRIPTION
Lower-cost capacitors expressly intended for high
density printed circuit board.
Ideally suited for general-purpose applications,
entertainment electronics.
Feature High CV Product with Moderate Cost
Multiplier for Ripple Current
Frequency (Hz)
6.3~100V Below~68µF
6.3~100V 100~680µF
6.3~110V 1000~22000µF
160~450V ALL Cap(µF)
120
1.00
1.00
1.00
1.00
300
1.20
1.10
1.05
1.05
1K 10K~100K
1.30
1.45
1.15
1.25
1.10
1.15
1.10
1.50
Temperature(°C)
Factor
65
1.80
85
1.40
105
1.00
DIAGRAM OF DIMENSIONS
4.0
5.0
6.0
8.0
10.0
12.0
13.0
16.0
18.0
22.0
F
1.5
2.0
2.5
3.5
5.0
0.45
0.5
Rubber Stand-off
Vinyl Sleeve
(P.V.C)
Rubber End Seal
Vinyl Sleeve
(P.V.C)
Dimensions : mm
Rubber End Seal
F 0.5
F 0.5
0.6
L
0.4Max.
15Min.
5Min.
D 0.5
L
15Min.
5Min.
D 0.5
7.5
10.0
0.8
0.8
Three key technologies of mobile robots
There are many issues to be studied in the field of robotics, involving multiple disciplines such as computers, sensors, human-computer interaction, and biosecurity. Among them, environmental percepti...
eastin8 Mobile and portable
FPGA implementation of terrestrial digital television symbol and carrier synchronization.pdf
FPGA implementation of terrestrial digital television symbol and carrier synchronization.pdf...
zxopenljx EE_FPGA Learning Park
Classic: MSP430 microcontroller enters low power mode program code
[size=4]Method to enter low power consumption: [/size] [size=4]#include "msp430x42x.h" [/size] [size=4]void main( void ) [/size] [size=4]{ [/size] [size=4] WDTCTL=WDTPW+WDTHOLD; //Stop watchdog [/size...
fish001 Microcontroller MCU
X-NUCLEO-IKS01A3 sensor test based on STM32F401RE development board 3D acceleration LIS2DW12 sensor test...
Today I tested the 3D sensor using the LIS2DW12_6Dorientation example. At first I thought this example was for testing acceleration, but after actual operation I realized it was for testing the sensor...
hujj MEMS sensors
ARM Embedded Learning Resource Sharing——"ARM Embedded Architecture and Interface Technology".pdf
This content is originally created by EEWORLD forum user ritinde . If you need to reprint or use it for commercial purposes, you must obtain the author's consent and indicate the source.Share a good b...
ritinde ARM Technology
Considerations for selecting solid-state relays
1. Load type, output current and surge current The steady-state current flowing through the output terminal of the relay during use shall not exceed the rated output current at the corresponding tempe...
fish001 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号