Military Established Reliability
Bulk Metal
®
Foil Technology
RNC90Y and RNC90Z (Z-Foil) to MIL-PRF-55182/9
FEATURES
QPL product with established reliability (ER)
“R” level high reliability resistor qualified to MIL-PRF-55182/9
Load life stability: ± 0.05 %
R
for 2000 h, 0.3 W at + 125 °C
Temperature coefficient of resistance (TCR): ± 2 ppm/°C max.
(- 55 °C to + 175 °C)
Resistance tolerance: to ± 0.005 %
Thermal EMF: < 0.1 µV/°C
Qualified resistance range: 4.99
to 121 k (RNC90Y)
30.1
to 121 k(RNC90Z)
Specially conditioned non-QPL resistors available
See data sheet “Improved Performance Tested”
Fast thermal stabilization
Electrostatic discharge (ESD) above 25 000 V
Non inductive, non capacitive design
Current noise < - 42 dB
Prototype sample available
INTRODUCTION
Military Established Reliability resistors from Vishay Foil
Resistors (VFR) are available in resistance values from
4.99
Ω
through 121 kΩ and with tolerances from ±0.005% to
±1.0%. The same resistors are also available as
non-qualified products for customers desiring higher or lower
resistance values and the same or better performance
capabilities (see Table 2). Both qualified and non-qualified
versions are manufactured on the same production line
facilities and are subjected to the same process, lot control,
conditioning, and GRP A (100%) screening. Qualified
versions receive additional MIL Group B and C testing.
The RNC90Y has been the benchmark for high-precision,
established-reliability discrete resistors since 1982. In 2000,
VFR engineers achieved a technological breakthrough with
the introduction of the commercial ultra-precision, low-TCR
Z201 resistor. This breakthrough allowed for the introduction
of a resistor with very low TCR and an “R” reliability level.
The RNC90Z TCR limit of ±2 ppm/°C over the extended
range of –55°C to +175°C is a significant improvement over
the existing RNC90Y specification.
The RNC90Z is a direct replacement for the RNC90Y.
FIGURE 1 - COMPARISON OF RNC90Y TO RNC90Z TEMPERATURE COEFFICIENT OF RESISTANCE
+ 1000
RNC90Y
+ 1000
+ 1000
RNC90Z
+ 1000
+ 500
+ 400
ΔR/R
(ppm)
ΔR/R
(ppm)
+ 160
0
- 160
+ 300
+ 200
0
- 200
- 300
- 400
- 500
- 1000
- 55
25
Temperature (°C)
125
- 1000
175
- 1000
- 55
25
Temperature (°C)
125
- 1000
175
Specification ± 5 ppm/°C ± 10 ppm/°C
Specification ± 2 ppm/°C
Document Number: 63007
Revision: 4-Jan-16
For any questions, contact
foil@vpgsensors.com
www.vishayfoilresistors.com
1
Military Established Reliability
TABLE 1 - SPECIFICATIONS COMPARISON
(1)
SPECIFICATION
Temperature
Coefficient of
Resistance
Resistance Range
Failure Rate
Load-Life Stability
0.3 W at + 125 °C
at 2000 h
at 10 000 h
Current Noise
High-Frequency
Operation
Rise Time
Inductance
(3)
(L)
Capacitance (C)
Voltage
Coefficient
Working Voltage
(4)
Thermal EMF
(5)
RNC90Y (QUALIFIED)
RNC90Z (QUALIFIED)
S555 (NON-QUALIFIED)
Z555 (NON-QUALIFIED)
MIL-PRF-55182/9
MIL-PRF-55182/9
VFR PERFORMANCE
VFR PERFORMANCE
CHARACTERISTIC Y LIMITS CHARACTERISTIC Z LIMITS
LIMITS
LIMITS
± 5 ppm/°C
± 2 ppm/°C
± 5 ppm/°C
± 3 ppm/°C ± 2.5 ppm/°C ± 2 ppm/°C
(- 55 °C to + 125 °C)
(- 55 °C to + 175 °C)
(- 55 °C to + 125 °C)
± 10 ppm/°C
(- 55 °C to + 125 °C)
(+ 125 °C to + 175 °C)
4.99
to
> 25
to
4.99
to 121 k
30.1
to 121 k
1
to 150 k
> 80
25
80
Level R
Level R
Not specified
Not specified
± 0.05 % maximum
R
± 0.5 % maximum
R
Not specified
± 0.05 % maximum
R
± 0.5 % maximum
R
Not specified
± 0.015 % maximum
R
(2)
± 0.05 % maximum
R
(2)
- 40 dB minimum
1.0 ns at 1 k
0.1 µH maximum
0.08 µH typical
1.0 pF maximum
0.5 pF typical
0.0001 %/V
300 V maximum
0.1 µV/°C maximum
1 µV/W maximum
± 0.015 % maximum
R
(2)
± 0.05 % maximum
R
(2)
- 40 dB minimum
1.0 ns at 1 k
0.1 µH maximum
0.08 µH typical
1.0 pF maximum
0.5 pF typical
0.0001 %/V
300 V maximum
0.1 µV/°C maximum
1 µV/W maximum
Not specified
Not specified
Not specified
0.0005 %/V
300 V maximum
Not specified
Not specified
Not specified
Not specified
0.0005 %/V
300 V maximum
Not specified
Notes
(1)
Qualification and failure rate verification test data is maintained by Vishay Foil Resistors and is available upon request. Lot traceability and
identification data is maintained by VFR for 7 years.
(2)
Load life
R
Maximum can be reduced by 80 % through a screening procedure. Consult our Applications Engineering for details.
(3)
Inductance (L) due mainly to the leads.
(4)
Not to exceed power rating of resistor.
(5)
µV/°C relates to EMF due to lead temperature differences and µV/W due to power applied to the resistor.
FIGURE 2 - TRIMMING TO VALUES
(Conceptual Illustration)
FIGURE 3 - POWER DERATING CURVE
+ 70 °C
Interloop Capacitance
Reduction in Series
Current Path
Before Trimming
Current Path
After Trimming
Trimming Process
Removes this Material
from Shorting Strip Area
Changing Current Path
and Increasing
Resistance
Percent of Rated Power
200
150
100
50
0
- 50
Rated Power
Mutual Inductance
Reduction due
to Change in
Current Direction
- 25
0
+ 25 + 50 + 75 + 100 + 125 + 150 + 175
Ambient Temperature °C
Note:
Foil shown in black, etched spaces in white
www.vishayfoilresistors.com
2
For any questions, contact
foil@vpgsensors.com
Document Number: 63007
Revision: 4-Jan-16
Military Established Reliability
FIGURE 4 - IMPRINTING AND DIMENSIONS
RNC90Y and RNC90Z Military Approved Resistors
Front View
L
VFR
0066A
XXXXX J
Side View
Manufacturers
Identification
Number
ST
JAN Designator
(not present if
non-qualified)
Lead Material
#22 AWG
(0.025 dia.)
Solder Coated
Copper
W
Resistance
Tolerance
Code
Rear View
Model Number
XXXXX
100R01
B
R
H
Mfr. Code
07
11
B
Factory Year Week
Resistance
Value Code
Failure Rate Code
(not present if
non-qualified)
LL
SW
LS
(1)
Note
(1)
0.200" (5.08 mm) lead spacing available - specify Model Number RNC90T for RNC90Y, and RNC90S for RNC90Z
TABLE 2 - MODEL SELECTION
STANDARD RESISTANCE
TOLERANCE
TIGHTEST
LOOSEST
%
%
30.1 to 121K
± 0.005
± 1.0
RNC90Y
16.2 to 30.0
± 0.05
± 1.0
4.99 to 16.0
± 0.1
± 1.0
RNC90Z
30.1 to 121K
± 0.005
± 1.0
30.1 to 121K
± 0.005
± 1.0
20 to < 30.1
± 0.01
± 1.0
5 to < 20
± 0.05
± 1.0
S555
(NON QPL)
2 to < 5
± 0.1
± 1.0
1 to < 2
± 0.5
± 1.0
± 0.005
± 1.0
> 121K to 150K
30.1 to 121K
± 0.005
± 1.0
Z555
20 to < 30.1
± 0.01
± 1.0
(NON QPL)
4.99 to < 20R
± 0.05
± 1.0
Note
MODEL
NUMBER
RESISTANCE
RANGE
()
FAILURE
RATE
M, P, R
(See
Table 3)
AVERAGE
WEIGHT
(g)
at + 70 °C at + 125 ° C
0.6 W
0.6 W
0.3 W
0.3 W
0.6
0.6
W: 0.105 ± 0.010
L: 0.300 ± 0.010
H: 0.326 ± 0.010
ST: 0.015 ± 0.005
SW: 0.040 ± 0.005
LL: 1.000 ± 0.125
LS: 0.150 ± 0.005
2.67 ± 0.25
7.62 ± 0.25
8.28 ± 0.25
0.38 ± 0.13
1.02 ± 0.13
25.4 ± 3.18
3.81 ± 0.13
AMBIENT
POWER RATING
DIMENSIONS
INCHES
mm
-
0.6 W
0.3 W
0.6
-
-
0.4 W
0.6 W
0.2 W
0.3 W
0.6
0.6
S555 and Z555 units are manufactured on the same production line facilities and are subjected to all the same process and lot control
requirements imposed on RNC90Y (Z) version, as well as all of the special screening, environmental conditioning and documentation stipulations
outlined in MIL-PRF 55182/9
Document Number: 63007
Revision: 4-Jan-16
For any questions, contact
foil@vpgsensors.com
www.vishayfoilresistors.com
3
Military Established Reliability
TABLE 3 - GLOBAL PART NUMBER INFORMATION
NEW GLOBAL PART NUMBER: Y1189100R500AR0L (preferred part number format)
DENOTES PRECISION
Y
VALUE
R
=
K
= k
LIFE FAILURE RATE (LFR)
(1)
R
= ± 0.01 %
P
= ± 0.1 %
M
= ± 1.0 %
AER
(2)
0
= standard
1 - 999
= custom
Y
1
1
8
9
1
0
0
R
5
0
0
A
R
0
L
PRODUCT CODE
1189
= RNC90Z
0089
= RNC90Y
1508
= RNC90T
1506
= RNC90S
0088
= S555
1288
= Z555
RESISTANCE TOLERANCE
V
= ± 0.005 %
T
= ± 0.01 %
A
= ± 0.05 %
B
= ± 0.1 %
D
= ± 0.5 %
F
= ± 1.0 %
PACKAGING
L
= bulk pack
R
= tape and reel
FOR EXAMPLE: ABOVE GLOBAL ORDER Y1189 100R500 A R 0 L:
TYPE: RNC90Z
VALUE: 100.5
ABSOLUTE TOLERANCE: ± 0.05 %
LIFE FAILURE RATE (LFR): ± 0.01 %
AER: standard
PACKAGING: bulk pack
HISTORICAL PART NUMBER: RNC90Z 100R50 A R B (will continue to be used)
RNC90Z
MODEL
RNC90Z
RNC90S
RNC90Y
RNC90T
S555
Z555
Note
(1)
Applicable
(2)
For
100R50
OHMIC VALUE
100.5
A
RESISTANCE
TOLERANCE
V
= ± 0.005 %
T
= ± 0.01 %
A
= ± 0.05 %
B
= ± 0.1 %
D
= ± 0.5 %
F
= ± 1.0 %
R
LIFE FAILURE
RATE (LFR)
(1)
R
= ± 0.01 %
P
= ± 0.1 %
M
= ± 1.0 %
B
PACKAGING
B
= bulk pack
only for QPL part. For S555 and Z555 please assign "0" instead.
non-standard requests, please contact application engineering.
www.vishayfoilresistors.com
4
For any questions, contact
foil@vpgsensors.com
Document Number: 63007
Revision: 4-Jan-16
Military Established Reliability
CAGE #0066A
“Commercial and Government Entity”
Formerly “FSCM”
The response of military and non military grade resistors to environmental stresses can be made better by “Improved
Performance Testing” (IPT). The IPT part will see burn-in and cycling that removes the “knee” from the normal drift of non IPT
parts. (See Table 4 for the improvement to expect in military parts when calling for VFR recommended screening). Users should
be aware that IPT testing renders the part non QPL and so a 3XXXXX part number will be assigned by VFR. Consult Applications
Engineering for details and ordering advice.
TABLE 4 - IMPROVED PERFORMANCE TESTING (NON-QPL) VS. QPL
TEST
GROUP
I
TEST
Burn-in
Thermal Shock and
Overload Combined
Resistance Temperature
Characteristic
Low Temperature Storage
Low Temperature Operation
Terminal Strength
DWV
Insulation Resistance
Resistance to Soldering Heat
Moisture Resistance
Shock
Vibration
Load Life at + 125 °C; 2000 h
Load Life at + 125 °C; 10 000 h
+ 85 °C Power Rating
+ 70 °C Power Rating
+ 25 °C Power Rating
Storage Life
High Temperature Exposure
Max. Allowance Reactance
Current Noise
Voltage Coefficient
Thermal EMF
RNC90Y
MIL-PRF-55182 & MIL-PRF-55182/9
METHOD PARAGRAPH
4.8.3.3
4.8.2
4.8.3
4.8.9
LIMITS
± 0.05 %
-
± 0.05 %
± 5 ppm/°C
VISHAY FOIL RESISTORS
IMPROVED PERFORMANCE
TESTING
(IPT) LIMITS
± 0.0025 %
-
± 0.005 %
< ± 2 ppm/°C
(- 55 °C to + 125 °C)
(Can be sorted for tighter tracking)
± 0.0025 %
± 0.0025 %
± 0.001 %
± 0.001 %
> 10
4
M
± 0.001 %
± 0.015 %
± 0.0025 %
± 0.0025 %
± 0.005 % (50 ppm)
± 0.015 % (150 ppm)
± 0.005 % (50 ppm)
± 0.005 % (50 ppm)
± 0.005 % (50 ppm)
± 0.0025 %
± 0.005 %
<1%
< - 42 dB
< 0.00001 %/V
(< 0.1 ppm/V)
0.1 µV/°C
II
III
IV
V
V (a)
V (b)
VI
VII
VIII
4.8.23
4.8.10
4.8.11
4.8.12
4.8.13
4.8.14
4.8.15
4.8.16
4.8.17
4.8.18
4.8.18
-
4.8.18
-
-
4.8.19
-
-
4.8.20
-
-
± 0.05 %
± 0.05 %
± 0.02 %
± 0.02 %
10
4
M
± 0.02 %
± 0.05 %
± 0.01 %
± 0.02 %
± 0.05 %
± 0.5 %
-
± 0.05 %
-
-
± 0.5 %
-
-
0.0005 %/V
(5 ppm/V)
-
FIGURE 5 - IPT IMPRINTING AND DIMENSIONS
in inches (millimeters)
Front View
0.300
±
0.010
(7.62
±
0.25)
VFR
XXXX
3XXXXX
Date Code
10
01
Year Week
0.015
±
0.005
(0.381
±
0.13)
Model Number
0.150
±
0.005
(3.81
±
0.13)
Lead Material
#22 AWG
(0.025 Dia.)
Solder Coated
Copper
0.040
±
0.005
(1.02
±
0.13)
Side View
0.105
±
0.010
(2.67
±
0.25)
Rear View
Optional
Customer
P/N
6 Digits Maximum
Resistance
Value Code
Tolerance
1.00
±
0.125
(25.4
± 3.18)
0.326
±
0.010
(8.28
±
0.25)
XXXXXX
100R01
0.01
%
Document Number: 63007
Revision: 4-Jan-16
For any questions, contact
foil@vpgsensors.com
www.vishayfoilresistors.com
5
Integrated technical exchanges
京公网安备 11010802033920号
EEWORLD
