ERL (Military RLR)
www.vishay.com
Vishay Dale
Metal Film Resistors, Military/Established Reliability,
MIL-PRF-39017 Qualified, Type RLR
FEATURES
• Meets requirements of MIL-PRF-39017
• Failure rate: Verified failure rate (contact factory for current
level)
• Epoxy coated construction provides superior moisture
protection
• Traceability of materials and processing
• Monthly lot acceptance testing
• Very low noise (-40 dB)
• Extensive stocking program at distributors and factory in
± 1 % and ± 2 % tolerances
• Vishay Dale has complete capability to develop specific
reliability programs designed to customer requirements
STANDARD ELECTRICAL SPECIFICATIONS
VISHAY
DALE
MODEL
ERL05,
ERL05..19
(3)
ERL07,
ERL07..23
(3)
MIL-PRF-39017
STYLE
RLR05
RLR07
MIL
SPEC.
SHEET
05
01
POWER
RATING
70 °C
W
0.125
0.25
RESISTANCE
RANGE
(1)
4.7 to 301K
302K to 1M
1 to 9.76
10 to 3.01M
3.02M to 10M
TOLERANCE
±%
1, 2
1, 2
TEMPERATURE
COEFFICIENT
± ppm/°C
100
100
MAXIMUM
WORKING
VOLTAGE
(4)
V
200
250
LIFE
FAILURE
RATE
(2)
M, P, R, S
M, P, R
M
M, P, R, S
M, P, R
ERL20,
RLR20
02
0.50
4.3 to 3.01M
1, 2
100
350
M, P, R, S
ERL20..11
(3)
ERL32,
RLR32
03
1.0
1 to 2.7M
1, 2
100
500
M, P, R
ERL32..1
(3)
Notes
(1)
Extended Resistance Range: DSCC has created a series of drawings intended to support extended resistance ranges left otherwise void by
the discontinuation of MIL-R-39008 RCR carbon composition resistors. Vishay Dale is listed as a resource on these drawings as follows:
MAXIMUM
DSCC
POWER RATING RESISTANCE
TEMPERATURE
VISHAY DALE
TOLERANCE
WORKING
DRAWING
P
70 °C
RANGE
COEFFICIENT
MODEL
±%
VOLTAGE
NUMBER
W
± ppm/°C
V
(4)
98020
ERL05..36, ERL05..37
(3)
0.125
1.1M to 22M
2, 5, 10
350
200
(3)
0.25
11M to 22M
2, 5, 10
350
250
99011
ERL07..100, ERL07..101
(3)
0.50
3.3M to 22M
2, 5, 10
350
350
98021
ERL20..36, ERL20..37
1.0
3M to 22M
2, 5, 10
350
350
98022
ERL32..36, ERL32..37
(3)
10 to 2.7M
100
2.0
1, 2, 5, 10
500
97004
ERL62..1, ERL62..2
(3)
3M to 22M
350
• Low inductance: DSCC has created a drawing intended to support a resistor which exhibits low inductance over a frequency range of 1 MHz
to 30 MHz. Vishay Dale is listed as a resource on these drawings as follows:
DSCC
DRAWING
NUMBER
96002
VISHAY DALE
MODEL
ERL07..62
POWER
RATING
P
70 °C
W
0.25
RESISTANCE
RANGE
MAXIMUM
INDUCTANCE
nH
TOLERANCE
±%
TEMPERATURE
COEFFICIENT
± ppm/°C
MAXIMUM
WORKING
VOLTAGE
V
(4)
(2)
(3)
(4)
1 to 10
10
1, 2
100
250
11 to 49.9
8
These drawings can be viewed at:
http://www.landandmaritime.dla.mil/Programs/MilSpec/ListDwgs.aspx?DocTYPE=DSCCdwg
Consult factory for current QPL failure rates
Hot solder dipped leads
Continuous working voltage shall be
P
x
R
or maximum working voltage, whichever is less.
TECHNICAL SPECIFICATIONS
PARAMETER
Voltage Coefficient, max.
Dielectric Strength
Insulations Resistance
Operating Temperature Range
Terminal Strength
Solderability
Weight
Revision: 25-Aug-15
UNIT
ppm/V
V
AC
°C
lb
g
CONDITION
5/V when measured between 10 % and full rated voltage
RLR05 = 300; RLR07 and RLR20 = 500; RLR32 = 1000
10
9
min. dry;
10
11
min. after moisture test
-65 to +150
2 lb pull test on RLR05; 5 lb pull test on all other sizes
Continuous satisfactory coverage when tested in accordance with MIL-STD-202, method 208
RLR05 = 0.11; RLR07 = 0.35; RLR20 = 0.75; RLR32 = 1.05
Document Number: 31023
1
For technical questions, contact:
ff2aresistors@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
ERL (Military RLR)
www.vishay.com
Vishay Dale
GLOBAL PART NUMBER INFORMATION
New Global Part Numbering: RLR07C3001FRR36 (preferred part numbering format)
R
L
R
0
7
C
3
0
0
1
F
R
FAILURE
RATE
R
3
6
MIL STYLE
RLR05
RLR07
RLR20
RLR32
LEAD MATERIAL
C
= solderable/
weldable
RESISTANCE
VALUE
3 digit
significant
figure,
followed by
a multiplier
Use “R” for
values < 100
1R00
= 1
3302
= 33 k
1005
= 10 M
TOLERANCE
CODE
F
=±1%
G
=±2%
PACKAGING
SPECIAL
M
= 1.0 %/1000 h
B14
= tin/lead, bulk Blank = standard
P
= 0.1 %/1000 h
BSL
= tin/lead, bulk,
(Dash number)
R
= 0.01 %/1000 h single lot date code
(Up to 3 digits)
S
= 0.001 %/1000 h
From
1 to 999
R36
= tin/lead,
as applicable
T/R (full, except 32’s)
1
= hot solder
R64
= tin/lead,
dip (32’s)
T/R (full; 32’s only)
11
= hot solder
RE6
= tin/lead,
dip (20’s)
T/R (1000 pieces)
19
= hot solder
RSL
= tin/lead, T/R,
dip (05’s)
single lot date code
23
= hot solder
dip (07’s)
F
R
FAILURE RATE
R36
PACKAGING
Historical Part Number Example: RLR07C3001FR (will continue to be accepted)
RLR07
MIL STYLE
C
LEAD MATERIAL
3001
RESISTANCE VALUE
TOLERANCE CODE
Note
• For additional information on packaging, refer to the Through Hole Resistor Packaging document (www.vishay.com/doc?31544).
DIMENSIONS
in inches (millimeters)
A
E
(1)
C
(Max.)
D
B
Note
(1)
Lead length for product in bulk pack. For product supplied in tape and reel, the actual lead length would be based on the body size, tape
spacing and lead trim.
VISHAY DALE
MODEL
ERL05
ERL07
ERL20
ERL32
ERL62
A
0.150 ± 0.020
(3.81 ± 0.51)
0.250 + 0.031 - 0.046
(6.35 + 0.79 - 1.17)
0.375 ± 0.041
(9.53 ± 1.04)
0.562 ± 0.031
(14.27 ± 0.79)
0.562 + 0.031 - 0.042
(14.27 + 0.79 - 1.07)
B
0.066 ± 0.008
(1.68 ± 0.21)
0.090 ± 0.008
(2.29 ± 0.21)
0.138 ± 0.023
(3.51 ± 0.58)
0.190 ± 0.015
(4.83 ± 0.38)
0.230 ± 0.015
(5.84 ± 0.38)
C
(Max.)
0.187
(4.75)
0.300
(7.62)
0.450
(11.43)
0.625
(15.87)
0.650
(16.51)
D
0.016 ± 0.002
(0.41 ± 0.05)
0.025 ± 0.002
(0.64 ± 0.05)
0.032 ± 0.002
(0.81 ± 0.05)
0.032 + 0.002 - 0.001
(0.81 + 0.05 - 0.03)
0.032 + 0.002 - 0.001
(0.81 + 0.05 - 0.03)
E
1.25 ± 0.266
(31.75 ± 6.76)
1.50 ± 0.125
(38.10 ± 3.18)
1.50 ± 0.125
(38.10 ± 3.18)
1.50 ± 0.125
(38.10 ± 3.18)
1.50 ± 0.125
(38.10 ± 3.18)
MATERIAL SPECIFICATIONS
Element
Core
Encapsulation
Termination
Vacuum-deposited nickel-chrome alloy
Fire-cleaned high purity ceramic
Specially formulated epoxy compound
Standard lead material is solder-coated
copper. Solderable and weldable per
MIL-STD-1276, Type C.
APPLICABLE MIL-SPECIFICATIONS
MIL-PRF-39017:
The ERL series meets the electrical, environmental and
dimensional requirements of MIL-PRF-39017.
MIL-PRF-22684:
MIL-PRF-39017 supercedes MIL-PRF-22684 on new designs. The
ERL series meet or exceed MIL-PRF-22684 requirements.
Documentation:
Qualification and failure rate verfication test data is maintained by
Vishay Dale and is available upon request. Lot traceability and
identification data is maintained by Vishay Dale for five years.
CAGE CODE: 91637
POWER RATING
Power ratings are based on the following two conditions:
1. ± 2.0 % maximum
R
in 2000 h load life
2. +150 °C maximum operating temperature
Revision: 25-Aug-15
Document Number: 31023
2
For technical questions, contact:
ff2aresistors@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
ERL (Military RLR)
www.vishay.com
Vishay Dale
RATED POWER IN %
120
100
80
60
40
20
0
- 65 - 50
- 25
HEAT RISE (°C ABOVE AMBIENT)
120
100
ERL05
ERL07
ERL20
80
ERL32
60
40
20
0
0
0.125
0.25
0.375
0.5
0.625
0.75 0.875
1 1.125
APPLIED POWER IN W
0
25
50
75
100
125
150
175
200
THERMAL RESISTANCE
DERATING
70 AMBIENT TEMPERATURE IN °C
MARKING
(per MIL-PRF-39017)
Tolerance: F = 1 %, G = 2 %
Value = three significant figures and multiplier
J = JAN (Joint Army - Navy) brand
RLR05: (3 lines)
210A
1002
FSJD
3-digit date code and lot code
Value
Tolerance, failure rate, JAN and manufacturer’s code
RLR07: (4 lines)
214AJ
RLR7C
1300G
RD
RLR20, RLR32: (4 lines)
91637
RLR20C
4993FR
1225AJ
CAGE code
Style and lead material
Value, tolerance and failure rate
4-digit date code, lot code and JAN
3-digit date code, lot code and JAN
Style (“0” omitted) and lead material
Value and tolerance
Failure rate and manufacturer’s code
Revision: 25-Aug-15
Document Number: 31023
3
For technical questions, contact:
ff2aresistors@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000
Power technology
京公网安备 11010802033920号
EEWORLD
