EEWORLDEEWORLDEEWORLD

Part Number

Search

RBR52L976R0DR

Description
Fixed Resistor, Wire Wound, 0.5W, 976ohm, 0.5% +/-Tol, -10,10ppm/Cel,
CategoryPassive components    The resistor   
File Size190KB,4 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

RBR52L976R0DR Overview

Fixed Resistor, Wire Wound, 0.5W, 976ohm, 0.5% +/-Tol, -10,10ppm/Cel,

RBR52L976R0DR Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
MakerTT Electronics plc
Reach Compliance Codecompli
ECCN codeEAR99
structureTubul
Lead diameter0.8 mm
Lead length38.1 mm
Maximum operating temperature145 °C
Minimum operating temperature-65 °C
Package diameter9.5 mm
Package length25.4 mm
Package shapeTUBULAR PACKAGE
Package formAxial
Rated power dissipation(P)0.5 W
GuidelineMIL-R-39005
resistance976 Ω
Resistor typeFIXED RESISTOR
seriesRBR(AXIAL)
technologyWIRE WOUND
Temperature Coefficient-10,10 ppm/°C
Tolerance0.5%
Axial Lead Precision
Wirewound Resistors
RB / RBR, VA / HR, SP / 7000 Series
Axial
1.0 watts
·
0.1 to
Lead Precision
Wirewound Resistors
·
Tolerance to ±.01%
·
0.1 ohm to 12 megohms
·
0.1 to 1.0 watts
to M, P, & R levels
Approved
·
Tolerance
from ±2 ppm/°C to +6000 ppm/°C
TCR’s
to ±.01%
·
0.1 ohm to
or exceeds all applicable
Meets
12 meg ohms
Approved to M, P, & R levels
RB / RBR, VA / HR, SP / 7000 Series
TCR’s from ±2 ppm/°C to +6000 ppm/°C
MIL-R-93 & MIL-R-39005 ratings
Meets or exceeds all applicable MIL-R-93 & MIL-R-39005 ratings
The RB/RBR ultra precision resistors are designed and produced for critical parameter applications. They are available
for established reliability military and/or commercial applications requiring state of the art precision and stability.
Construction features may vary slightly between commercial and military styles, but both are produced under the same
rigid quality control system required by the tightest military specifications. Both are produced in the same production
line using the same highly trained operators required to produce the established reliability product.
All terminations are welded to reduce contact noise and thermal EMF. Extensive accelerated aging programs both
before and after calibration assure precise initial accuracy and high resistance stability.
Encapsulation is accomplished by a unique dry air chamber epoxy shell technique for established reliability parts. A
resilient inner coating is used to minimize internal stresses on all parts.
All resistors (military and commercial) are carefully monitored during assembly, winding, coating, and stabilization
procedures to assure high quality standards. Premium grade selected wire is control- stress wound on special designed
bobbins. Established reliability military parts are then burned in for 100 hours at 125°C ambient as part MIL-R-93, or
equivalent, of group A acceptance testing. Documentation and special tests are available upon customer request to
meet your unique requirements.
TCR and Temperature Data
Style
All
Styles
Resistance Range ()
0.1 - 0.9
1.0 - 9.9
10 - 99.9
100 - 12M
Absolute TCR (ppm/°C)
±90
±30
±15
±10
-65 to +145
Operating Temperature Range (°C)
Special Screening / Acceptance Test:
Special tests can be performed on a 100% or sample basis, to meet individual customer requirements. Some of the
available non-destructive tests include:
Short Time Overload
Thermal Shock
Mechanical Shock
Vibration
Temperature Coefficient of Resistance
Radiographic Inspection
Each of these tests is designed to detect a spectrum of potential resistor defects. Consult the factory for recommendations
and a quotation on special screening or acceptance tests to meet your needs.
General Note
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data
to make changes in product specification without notice or liability.
TT electronics reserves the right
and is considered accurate at time of going to print.
All information is subject to TT electronics’ own data and is considered accurate at time of going to print.
Wire and Film Technologies Division
rpus Christi Te
Telephone:
© TT electronics plc
Facsimile:
Website: www.irctt.com
www.bitechnologies.com www.irctt.com www.welwyn-tt.com
RB/RBR, V
r
A subsidiary of
TT electronics plc
09. 11
Experience in using TI DSP/BIOS and CCS
1. When opening/creating a project with CCS, the path name where the project is stored cannot contain Chinese characters! (Unlike VS6, ISE, etc., which can use any path name)2. Some domestic parallel ...
fish001 Microcontroller MCU
Four-layer PCB proofing matters needing attention
Four-layer board refers to PCB made of 4 layers of fiberglass. What should be paid attention to in four-layer PCB proofing? Generally speaking, there are two groups, one is the engineer group and the ...
中信华 PCB Design
Why your 4.7uF capacitor becomes 0.33uF, it's incredible!
A few years ago, after more than 25 years of working with ceramic capacitors, I had a new appreciation for them. I was working on an LED light bulb driver when it became apparent that there was someth...
Jacktang Power technology
Industry 4.0 has a bright future, but the road is tortuous. Download the "Fluke Industrial Automation Industry Application Product Manual" to learn more!
The global manufacturing industry is currently undergoing a digital transformation, and technologies such as big data, artificial intelligence, 5G, and machine vision are expected to become new growth...
eric_wang Industrial Control Electronics
The relationship between capacitance and frequency
The relationship between capacitance and frequency Generally, the frequency exceeding the standard can be found by scanning with EMC equipment. The frequency is known. Then, according to the calculati...
QWE4562009 Test/Measurement
Help: "There are so many types of push button switches. Will choosing one have any impact on the physical hardware design?"
What is the impact of the slight difference in switch stem length between 6*6*4.3, 6*6*4.5 and 6*6*5 on the actual hardware? I am confused about which one to choose and I don't know if there are other...
biu12138biu PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号