[align=left][font=微软雅黑Light]Good things should be shared[/font]~[/align][align=left]ADI's Analog Dialogue, which never stops updating, has been updated again! Print and electronic versions are availab...
MSP430 can choose to use up to three oscillators depending on the model. We can choose the appropriate oscillation frequency according to our needs, and we can turn off the oscillator at any time when...
[i=s]This post was last edited by zhang1gong on 2022-1-8 10:49[/i]1 Generate the code for the EXAMPLE PROJECT project and run it
Running "Bluetooth - SoC Blinky" successfully, the LED on the BG22-EK41...
I am very disappointed. I have been debugging for so long but have not made any progress. I have never used HAL library, CUBEMX and CUBEide, which results in the serial port printing not being availab...
[backcolor=white][size=4][color=#000000]As a novice in embedded programming, I first need to install the embedded system development tool IAR, of course, the cracked version. But I encountered some pr...
Provides more accurate current measurement and control for automotive and industrial applications Beijing, China, November 16 , 2023 – Littelfuse Corporation , an industrial technology ...[Details]
"When Xilinx launched the Alveo product line in 2018, we had a vision: not only to accelerate computing, but also to accelerate networking and storage, and achieve overall acceleration on the Alveo p...[Details]
On May 8, Japan's Space Policy Committee decided to expand its Michibiki - Quasi-Zenith Satellite System, a satellite network operating in geosynchronous orbit over Japan and Australia.
...[Details]
The external interrupt of STM8 is different from that of STM32. Each port PX has only one interrupt. 2. ADC 1) Additional AIN12 analog input is not selectable in ADC scan mode or with analog wat...[Details]
1 Question In the following test program, if the '|' is removed from CLK_CKDIVR |= 0x08; in the Init_CLK() function, the function of TIM1 is the same as the preset (interrupt once every 10ms), bu...[Details]
Intel's full-year outlook was quite optimistic, estimating adjusted sales of approximately $73.5 billion, higher than analysts' expectations of $73.1 billion. Intel also announced that more than 100 ...[Details]
In modern automatic control equipment, there is a problem of interconnection between electronic circuits (weak current) and electrical circuits (strong current). On the one hand, the control signal o...[Details]
1. Circuit design and EMC device selection At the beginning of a new design and development project, the correct selection of active and passive components and perfect circuit design technology wil...[Details]
When it comes to LED drive accuracy, constant current error usually comes to mind. In fact, drive accuracy is not limited to current accuracy. LED is a typical current-driven device. Accurately c...[Details]
The MOSFET selection in the MAX8720 circuit is shown in the figure. The current conditions are Vin=7~24V, Vout=1.25V, Iout(max)=15A, FSW=300kHz, the controller's operating voltage (bias voltage) VC...[Details]
Current probes are generally divided into three types: high-frequency current probes, low-frequency current probes, and mutual induction coils. The high-frequency current probe adopts SMT large...[Details]
LG Electronics (LG) and Magna International (Magna) have signed a cooperation agreement to establish a new joint venture, LG Magna e-Powertrain, headquartered in Incheon, South Korea. The two parties...[Details]
As shown in the figure, this is a light-off reminder circuit. The circuit consists of a monostable delay circuit, a drive circuit, a buzzer, a light-emitting diode, etc. The output signal of the mo...[Details]
Abstract: The necessity of studying the programming implementation of multi-artificial interference algorithms is proposed. Based on the preliminary analysis of this part, the definition of such...[Details]
The soft start cabinet is an electrical device used for motor starting. It controls the voltage and current during the motor starting process to achieve smooth starting of the motor, reduce the cur...[Details]