Additional values may be available. Please contact us for more information. Due to demand and raw material fluctuations, specific values may not be available.
Email:
sales@venkel.com
|
Phone:
512.794.0081
|
Toll Free:
800.950.8365
|
Web:
www.venkel.com
Rev. 04/2018
3
High Q Low ESR Ceramic Capacitors
(HLC Series)
Tape and Reel Specifications
G
Reel Dimensions
Tape
B min
2.0
(0.07)
C
13 ± 0.05
(0.512 ± 0.02)
A (7”)
178 ±2.0
(7 ± 0.079)
A (13”)
330 ± 2.0
(13± 0.08)
D min
20.2
(0.795)
N min
50
(1.97)
G
8mm
Unit: mm (inch)
T max
14.9
(0.587)
All tape and reel
specifications must
be adhered to per
EIA-481-1-A.
B
A
D
FULL RADIUS
N
C
10 ± 1.5
(0.394 ± 0.059)
Taping Specifications
To
T
D
10 Pitches
Cumulative
Tolerance
0.008
( 0.2)
T
7 in. Reel Quantities**
Size
Tape Size
0201
8mm
15,000
15,000
0402
8mm
10,000
10,000
0603
8mm
4,000
4,000
0805
8mm
3,000
5,000
Min Qty Per
Reel
Max Qty Per
Reel
Po
Pz
E
A
B
F
W
T
Paper
Embossed
Top Tape
P
Center
Of Cavity
Direction Of Feed
Note:
** Quantity dependent on thickness
*Smaller quantities may be available. Please contact us.
B
W
F
E
Po
Pz
2.0 ± 0.05
- 0.0
(.039 ± .002)
- .000
2.0 ± 0.05
- 0.0
(.039 ± .002)
- .000
2.0 ± 0.05
- 0.0
(.039 ± .002)
- .000
2.0 ± 0.05
- 0.0
(.039 ± .002)
- .000
D
t
Unit: mm (inch)
P
Size
(inches)
A
Paper Tape
Carrier
Dimensions
(8mm)
0201
0.37 ± 0.05
(0.014 ± .002)
0.67 ± 0.05
(0.026 ± .002)
8.0 ± 0.2
(.315 ± .008)
3.5 ± 0.1
(.138 ± .004)
1.75 ± 0.1
(.069 ± .004)
4.0 ± 0.1
(.157 ± .004)
(
.064 + .004
)
(
.064 + .004
)
(
.064 + .004
)
(
.064 + .004
)
1.5 + 0.1
1.5 + 0.1
1.5 + 0.1
1.5 + 0.1
1.15
max
(.045
max
)
2.0 ± 0.05
(.079 ± .002)
0402
0.65 ± 0.1
(.026 ± .004)
1.10 ± 0.2
(.043 ± .008)
8.0 ± 0.2
(.315 ± .008)
3.5 ± 0.1
(.138 ± .004)
1.75 ± 0.1
(.069 ± .004)
4.0 ± 0.1
(.157 ± .004)
1.15
max
(.045
max
)
2.0 ± 0.05
(.079 ± .002)
0603
1.10 ± 0.2
(.043 ± .008)
1.90 ± 0.2
(.075 ± .008)
8.0 ± 0.2
(.315 ± .008)
3.5 ± 0.1
(.138 ± .004)
1.75 ± 0.1
(.069 ± .004)
4.0 ± 0.1
(.157 ± .004)
1.15
max
(.045
max
)
4.0 ± 0.1
(.157 ± .004)
0805
1.16 ± 0.2
(.046 ± .008)
2.4 ± 0.2
(.095 ± .008)
8.0 ± 0.2
(.315 ± .008)
3.5 ± 0.1
(.138 ± .004)
1.75 ± 0.1
(.069 ± .004)
4.0 ± 0.1
(.157 ± .004)
1.15
max
(.045
max
)
4.0 ± 0.1
(.157 ± .004)
Embossed
Carrier
Dimensions
(8mm)
Size
(inches)
0805
A
1.48 ± 0.2
(.058 ± .008)
B
2.3 ± 0.2
(.091 ± .008)
W
8.0 ± 0.2
(.315 ± .008)
F
3.5 ± .0.1
(.138 ± .004)
E
1.75 ± 0.1
(.069 ± .004)
Po
4.0 ± 0.1
(.157 ± .004)
Pz
2.0 ± 0.05
(.079 ± .002)
D
1.5 + 0.1
- 0.0
.06 + .004
- .000
To
2.5
max
(.098
max
)
T
0.6
max
(.024
max
)
P
4.0 ± 0.1
(.157 ± .004)
(
)
4
Email:
sales@venkel.com
|
Phone:
512.794.0081
|
Toll Free:
800.950.8365
|
Web:
www.venkel.com
Rev. 04/2018
High Q Low ESR Ceramic Capacitors
(HLC Series)
Environmental Test Criteria
No.
1
Item
Visual and
Mechanical
Capacitance
Q/ D.F.
(Dissipation
Factor)
Dielectric Strength
* To apply voltage: ( ≤100V ) 250% of rated voltage.
* Duration: 1 to 5 sec.
* Charge and discharge current less than 50mA.
* To apply voltage:
200V~300V ≥2 times VDC
500V~999V ≥1.5 times VDC
* Cut-off, set at 10mA
* TEST= 15 sec.
* RAMP=0
Rated voltage:<200V
To apply rated voltage for max. 120 sec.
Rated voltage:200~630V
To apply rated voltage (500V max.) for 60 sec.
With no electrical load.
Operating temperature: -55~125°C at 25°C
* Pressurizing force:
5N (≤0603) and 10N (>0603)
* Test time: 10±1 sec.
* Vibration frequency: 10~55 Hz/min.
* Total amplitude: 1.5mm
* Test time: 6 hrs. (Two hrs each in three mutually perpendicular directions.)
* Cap./DF(Q) Measurement to be made after de-aging at
150°C for 1hr then set for 24±2 hrs at room temp.
* Solder temperature: 235±5°C
* Dipping time: 2±0.5 sec.
The middle part of substrate shall be pressurized by means
of the pressurizing rod at a rate of about 1 mm per second until the deflection
becomes 1 mm and then the pressure shall be maintained for 5±1 sec.
* Measurement to be made after keeping at room temp. for 24±2 hrs.
京公网安备 11010802033920号
EEWORLD
