This product line is a family of state-of-the-art high performance 1550 nm
externally modulated CATV fiber optic transmitters optimized for varying network
applications. Packaged in convenient 1RU housing, this line of optical transmitters
couples high optical output powers, up to 10.0 dBm, with low optical line width
resulting in unmatched performance. The optical modulator, combined with
proprietary pre-distortion circuitry, provides superior CTB and CSO performance
with SBS suppression levels of greater than 17 dBm for SAT-IF applications.
Advanced features such as built in field adjustable SBS control allow these
transmitters to be quickly optimized in the field for any link or application without
the need to procure specifically tuned transmitters. This affords the system
designer a level of flexibility previously unknown in the CATV market place.
The J-Type series are designed as a high performance solution for applications
where the simultaneous transport of CATV and SAT-IF FM signals is required.
The SAT-IF signals can be applied anywhere in the 950 to 2800 MHz band.
J-Type transmitters are specially designed and optimized to support optical fiber
links of up to 150kms for the Japanese market place.
Applications
High Performance Supertrunking Links
High Power Distribution Networks
Redundant Ring Architectures
FTTx Networks
RFOG Applications
SAT-IF Transport
DWDM Node Splitting
Features
Single or Dual Optical Outputs
QAM Loading to 1003 MHz
Dual Power Supplies, Redundant &
Hot Swappable
Front Panel RF Test Point
Vacuum Fluorescent Status Display
OMI / RF Gain Adjustment
AGC Select: CW, Video, Manual
(No AGC)
Industry Leading Field Adjustable
SBS Suppression
.
| REV 2012.07
Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.
J-Type Medallion 6000 1550 nm
Externally Modulated Transmitter
DATASHEET | JULY 2012
FIBER OPTICS
Optical Characteristics
Property
Performance (note 1-8)
Specified Link Length
Channel Plan
Optical Output Power
Noise Bandwidth
SBS Suppression
CATV Carrier to Noise Ratio
CATV Composite Second Order
CATV Composite Triple Beat
CATV Composite Triple Beat
SAT-IF Carrier to Noise Ratio
SAT-IF Intermodulation Products
SAT-IF Spurious Products
Po (dBm)
BW (MHz)
(dBm)
CNR (dB)
CSO (dBc)
CTB (dBc)
CTB (dBc)
CNR (dB)
(dBc)
(dBc)
Units
L (km)
Models
6000-J01
6000-J02
25
NTSC 80-Ch
8.5/8.5
4
15.0
51.0
-65
-65
-64
27
-35
-38
25
PAL 60-Ch
8.5/8.5
5
15.0
51.0
-65
-65
-64
27
-35
-38
Min.
Min.
Max. Port 1
Comments
With 36 QPSK carriers from 950 to
2800 MHz
Min. 10 dBm version avail. See Chart
Max. @ +25C
Max. @ 0 C to 50 C
Min.
Max. Port 1
Max.
o
o
Notes:
1. Unless stated otherwise all specifications apply over full temperature range with no digital loading.
2. Unless stated otherwise specifications apply for nominal RF input level as defined below, after a 30 minute stabilization
period.
3. Specifications separated by a slash are port1 / port 2.
4. Units are tested per the Test / Link Configuration Table
5. Noise figure for the EDFA = 4.5 ~ 5.5 dB
6. Corning SMF-28 single mode fiber
7. Receiver responsivity is 0.95 mA/mW, Equivalent noise current is 7 pA/(Hz)1/2
8. With 36 QPSK modulated SAT-IF signals between 950
…
2800 MHz. 27 MHz IF bandwidth
Test/Link Configuration
Property
J-Type
14 dBm
EDFA
25 Km
Link
Received Power
2
0.0 dBm at the receiver
| REV 2012.07
Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.
J-Type Medallion 6000 1550 nm
Externally Modulated Transmitter
DATASHEET | JULY 2012
FIBER OPTICS
Electrical Specifications
Property
CATV Nominal Input Power
CATV Input Range
CATV Composite Level
CATV RF Gain / OMI Adjustment
Range
CATV Frequency Range
CATV Flatness
CATV Flatness – N-Type
CATV Input impedance
CATV Input Return Loss
CATV Front Panel RF Tap
CATV Front Panel RF Tap Flatness
SAT Nominal Input Power
SAT Input Range
SAT Composite Level
SAT-IF RF Gain / OMI Adjustment
Range
SAT-IF Frequency Range
SAT-IF Flatness
SAT-IF Input impedance
SAT-IF Input Return Loss
SAT-IF Front Panel RF Tap
SAT-IF Front Panel RF Tap Flatness
Requirement
19 dBmV/ch (79 dBuV/ch)
17 – 27 dBmV/ch (77 – 87 dBuV/ch)
-10.9 dBm
+2 / -8 dB from nominal setting
45MHz – 1003 MHz
+/- 0.50 dB
+/- 0.75 dB
+/- 0.75 dB
75
16dB min
-20 +/- 1 dB down from RF input
+/- 1 dB
27 dBmV/ch (87 dBuV/ch)
22 – 32 dBmV/ch (82 – 92 dBuV/ch)
-6.2 dBm
+5 / -5 dB from nominal setting
950MHz – 2800 MHz
+/- 2 dB
75
10dB min
7 +/- 2.5 dBmV/Ch at Nominal OMI/ch
+/- 1 dB
Comments
80 NTSC channels
Optimum performance at nominal input
0 dB on FP Display
CATV Performance may vary slightly over
range
45MHz - 550MHz
45MHz – 1003 MHz
45MHz – 1003 MHz N-Type
45MHz – 1003 MHz
45MHz – 1003 MHz
36 QPSK SAT-IF channels
Optimum performance at nominal input
0 dB on FP Display
CATV Performance can vary slightly
950MHz – 2800 MHz
950MHz – 2800 MHz
General and Mechanical Specifications
Property
Wavelength
Channel Plan
Optical Connector
Monitoring Interfaces
Operating Temperature
Storage Temperature
Power Consumption
1550 +/-5 nm
Various – See Specification Tables
SC/APC
100 Base-T Ethernet (SNMP)
Rear Panel RS-232 interface
VFD Screen Front Panel Controls
0C to 50C
-20C to 70C
65W max
Requirement
Comments
Various Options + ITU-grid available – see
Model Number Information
Custom channel plans available
Other styles available
VFD- (Vacuum Fluorescent Display)
| REV 2012.07
Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.
J-Type Medallion 6000 1550 nm
Externally Modulated Transmitter
DATASHEET | JULY 2012
FIBER OPTICS
General and Mechanical Specifications (continued)
Property
Requirement
EMI:
EN50083-2:2006 (US CATV)
EN55022:2006 (US IT)
EN61000-3-2 (Harmonics)
EN61000-3-3 (Flicker)
FCC: Part 15, Subpart B, class “A” Unintentional
Radiators
ICES-003 (Canada)
AN/NZS 3548, Class A (Australia)
VCCI, Class A (Japan)
GR-2853-CORE
GR-2853-CORE
(VAC)
(VDC)
Dimensions
20% to 85%
90 to 265 VAC, 50/60 Hz
+/- (36 – 72) VDC
19.0”W x 15.0”D x 1.72”H
(width includes 19” front panel ears, depth
includes, connectors, fans & front panel) – see
drawing
Comments
Safety:
FDA/CDRH Laser Safety Governed by Code
of Federal Regulations Title 21, Volume 8,
Part 1040
IEC 60950-1
IEC 60728-11
Laser IEC 60825-1
CB Certification
In Shipping package
In Shipping package
Non-condensing
Agency Listings
Transportation Vibration
Transportation Shock
Operating Humidity
Supply Range
Laser Safety Information
This product meets the applicable requirements of 21 CFR 1010 & 1040 and is classified as a class 1M
laser product. During use as intended, the laser energy is fully contained within the fiber network
such that there is no accessible laser radiation. This product has been issued accession number 0820466-001.
| REV 2012.07
Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.
J-Type Medallion 6000 1550 nm
Externally Modulated Transmitter
DATASHEET | JULY 2012
FIBER OPTICS
Model Number Information
Note 3
6000 –
Logo &
Customer
Specific
0
–
EMCORE
Logo
1
– no Logo
□□□ □
-
□ □□□□
Pout (dBm min)
Note 1
D –
10/10 for S and J Type
Link type
J –
25 km
Loading
Type
1
– NTSC
(80-ch)
2
– PAL
(60-ch)
Optics
1
– SC/APC, Rear
2
– FC/APC, Rear
3
– E2000/APC,
Rear
4
– SC/APC,
Front
5
– FC/APC,
Front
6
– E2000/APC,
Front
RF
1
– RF IN
Rear, TP
Front
2
– RF IN
Front, TP
Front
3
– RF IN
Front, TP
Rear
4
– RF IN
Rear, TP
Rear
Wavelength
(nm)
00
–1555+/-
5.0nm
01
– 1550+/-
5.0nm
xx
– ITU
Channel +/-
Note 2
0.1nm
Power Supply
1
– AC primary,
no secondary
2
– DC primary,
no secondary
3
– AC primary,
AC secondary
4
– AC primary,
DC secondary
5
– DC primary,
DC secondary
Note 4
E
– 8.5/8.5 for J Type
Note 1: Options available for Indicated Types only.
Note 2: ITU grid wavelengths can be specified from channel 18 to 40.
Note 3: Not all configurations are available, contact factory.
Note 4: CSO port 2 degraded by 1dB
Note 5: Contact Factory for Model type availability
Additional Kits
G3708-006-001 - Replaceable AC power supply modules
G3708-005-001 - Replaceable DC power supply modules
G7914-076-001 - Replaceable Blank power module plate
G7906-008-001 - Replaceable fans
| REV 2012.07
Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.
京公网安备 11010802033920号
EEWORLD
