Ordering Information .................................................................................................................................................................... 2
7.1. User Programming Interface ..................................................................................................................................... 19
7.2. Start-up output frequency and signaling types .......................................................................................................... 19
8.1. Any-frequency function ............................................................................................................................................. 20
9 I C/SPI Control Registers...................................................................................................................................................... 29
9.1. Register Address: 0x00. DCO Frequency Control Least Significant Word (LSW) .................................................... 29
9.2. Register Address: 0x01. OE Control, DCO Frequency Control Most Significant Word (MSW) ................................. 30
9.3. Register Address: 0x02. DCO PULL RANGE CONTROL ........................................................................................ 31
9.4. Register Address: 0x03. Flac-N PLL Integer Value and Flac-N PLL Fraction MSW ................................................. 32
9.6. Register Address: 0x05. PostDiv, Driver Control ...................................................................................................... 33
9.7. Register Address: 0x06. mDriver, Driver Control ...................................................................................................... 34
2
10 I C Operation ........................................................................................................................................................................ 35
2
10.1. I C protocol ............................................................................................................................................................... 35
2
10.2. I C Timing Specification ............................................................................................................................................ 37
2
10.3. I C Device Address Modes ....................................................................................................................................... 38
Dimensions and Patterns ........................................................................................................................................................... 45
Additional Information ................................................................................................................................................................ 46
Revision History ......................................................................................................................................................................... 47
Rev 0.991
Page 3 of 47
www.sitime.com
SiT3521
1 to 340 MHz Elite™ I
2
C/SPI Programmable Oscillator
1 Electrical Characteristics
PRELIMINARY
All Min and Max limits in the Electrical Characteristics tables are specified over temperature and rated operating voltage with
standard output terminations shown in the termination diagrams. Typical values are at 25°C and nominal supply voltage.
Table 1. Electrical Characteristics – Common to LVPECL, LVDS and HCSL
Parameter
Output Frequency Range
Frequency Stability
Symbol
f
F_stab
Min.
1
-10
-20
-25
-50
First Year Aging
Operating Temperature Range
F_1y
T_use
–
-20
-40
-40
Supply Voltage
Vdd
2.97
2.7
2.52
2.25
Input Voltage High
Input Voltage Low
Input Pull-up Impedance
Duty Cycle
Start-up Time
Output Enable/Disable Time –
Hardware control via OE pin
Output Enable/Disable Time –
Software control via I
2
C/SPI
VIH
VIL
Z_in
DC
T_start
T_oe_hw
70%
–
–
45
–
–
Typ.
–
–
–
–
–
±1
–
–
–
3.3
3.0
2.8
2.5
–
–
100
–
–
–
Max.
340
+10
+20
+25
+50
–
+70
+85
+105
Supply Voltage
3.63
3.3
3.08
2.75
–
30%
–
55
3.0
3.8
V
V
V
V
Vdd
Vdd
kΩ
%
ms
µs
Measured from the time Vdd reaches its rated minimum value
Measured from the time OE pin reaches rated VIH and VIL to
the time clock pins reach 90% of swing and high-Z.
See
Figure 9
and
Figure 10
Measured from the time the last byte of command is
transmitted via I
2
C/SPI (reg1) to the time clock pins reach 90%
of swing and high-Z. See
Figure 30
and
Figure 31
OE pin
OE pin
OE pin, logic high or logic low
Unit
MHz
ppm
ppm
ppm
ppm
ppm
°C
°C
°C
1 -year aging at 25°C
Extended Commercial
Industrial
Extended Industrial. Available only for I C operation, not SPI.
2
st
Condition
Factory or user programmable, accurate to 6 decimal places
Inclusive of initial tolerance, operating temperature, rated
power supply voltage and load variations.
Frequency Range
Frequency Stability
Temperature Range
Input Characteristics – OE Pin
Output Characteristics
Startup and Output Enable/Disable Timing
T_oe_sw
–
–
6.5
µs
Rev 0.991
Page 4 of 47
www.sitime.com
SiT3521
1 to 340 MHz Elite™ I
2
C/SPI Programmable Oscillator
Table 2. Electrical Characteristics – LVPECL Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
PRELIMINARY
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Maximum Output Current
Idd
I_OE
I_leak
I_driver
–
–
–
–
–
–
0.15
–
89
58
–
32
mA
mA
A
mA
Excluding Load Termination Current, Vdd = 3.3V or 2.5V
OE = Low
OE = Low
Maximum average current drawn from OUT+ or OUT-
Output Characteristics
Output High Voltage
Output Low Voltage
Output Differential Voltage Swing
Rise/Fall Time
VOH
VOL
V_Swing
Tr, Tf
Vdd - 1.1V
Vdd - 1.9V
1.2
–
–
–
1.6
225
Vdd - 0.7V
Vdd - 1.5V
2.0
290
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[3]
Note:
3. Measured according to JESD65B.
T_jitt
–
0.225
0.1
0.225
0.11
1
0.340
0.14
0.340
0.15
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3V or 2.5V
V
V
V
ps
See
Figure 5
See
Figure 5
See
Figure 6
20% to 80%, see
Figure 6
Table 3. Electrical Characteristics – LVDS Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Idd
I_OE
I_leak
–
–
–
–
–
0.15
80
61
–
mA
mA
A
Excluding Load Termination Current, Vdd = 3.3V or 2.5V
OE = Low
OE = Low
Output Characteristics
Differential Output Voltage
Delta VOD
Offset Voltage
Delta VOS
Rise/Fall Time
VOD
ΔVOD
VOS
ΔVOS
Tr, Tf
250
–
1.125
–
–
–
–
–
–
400
455
50
1.375
50
470
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[4]
Note:
4. Measured according to JESD65B.
T_jitt
–
0.21
0.1
0.21
0.1
1
0.275
0.12
0.367
0.12
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3V or 2.5V
mV
mV
V
mV
ps
f = 156.25MHz See
Figure 7
See
Figure 7
See
Figure 7
See
Figure 7
Measured with 2 pF capacitive loading to GND, 20% to 80%,
[i=s] This post was last edited by littleshrimp on 2019-2-27 19:04 [/i] LPS22HB data sheet:LPS22HB application notes:LPS22HB official evaluation board gerber files:LPS22HB schematic library:LPS22HB PC...
In PADS, the VIA Stitch is grayed out. I have set the Via Patterns in Options, but it still remains grayed out. Can anyone tell me what is going on? I am using PADS 9.3, a cracked version.
Thank you f...
[align=left]The trade-in of old instruments has begun! Keysight is calling you to exchange for new network analyzers[/align][align=left][font=微软雅黑][size=3] [/size][/font][/align][align=left][font=微软雅黑...
Overview :
There are two main topologies of non-isolated DC-DC power supplies that are most commonly used in our onboard power supplies: BUCK and BOOST. Inductance is a key parameter. This article bri...
With the advancement towards a carbon-free society and the shortage of energy, the world has high hopes for renewable energy, and has put forward higher requirements for continuously improving ener...[Details]
/*------------------------------------------------ --------------------------
ST7920.H
The user function is C51.
Copyright (c) 1988-2004 Keil Elektronik GmbH sum zhaojun
All rights reserved.
---...[Details]
Applied Materials Details Progress on Its 10-Year Sustainability Roadmap • Applied Materials' latest Sustainability Report outlines the company's efforts to reduce its carbon footprint and increas...[Details]
Function and installation of frequency converter
Variable-frequency Drive (VFD) is a power control device that uses frequency conversion technology and microelectronics technology to control A...[Details]
I have been engaged in RF system testing for some time. After engineering testing practice, I have summarized the uses. It can be used to measure and display the frequency and amplitude of the meas...[Details]
On July 26, a ceremony was held at the Honeycomb Energy Yancheng Base to announce the official start of production of the first flying stack short blade battery cell production line of the second phas...[Details]
Sustainability has undoubtedly become one of the focus issues in modern industrial manufacturing. This requires not only the materials used to be sustainable, but also the production processes. Susta...[Details]
On May 29, the Weipai coffee series launched its eighth OTA upgrade, with a total of 153 upgrades for Mocha, Latte, and Macchiato, including new features such as talk-while-execution, red light cou...[Details]
Chinese society should highly respect and understand Huawei, and support it in the way it needs, rather than burdening it with excessive moral responsibilities that it cannot bear as a commercial com...[Details]
On February 12, according to the Guangzhou Daily, yesterday morning, the Guangzhou Municipal Government held a consultation meeting with representatives of semiconductor and integrated circuit compan...[Details]
Since the parts of the tube amplifier are large in size and the ground wire is directly connected to the metal bottom plate, the heat dissipation during welding is strong. Therefore, a 55W internal h...[Details]
Morning news on January 5, Beijing time. According to reports, on Wednesday local time, the U.S. Federal Communications Commission (FCC) announced a proposed new policy to provide radios that require...[Details]
TSMC went to the United States to invest in a new factory in Arizona. On the 6th, Taiwanese Gong Mingxin attended the commissioning ceremony of the new factory as a director of TSMC. On the 7th, he v...[Details]
//****************************************************************************** // D13x Example 4 - 12-bit AD conversion // // Description: The system is in sleep state LPM0 // If the AD sampling va...[Details]
According to foreign media reports, Ford Motor Company has applied for a patent from the U.S. Patent and Trademark Office (USPTO) for an adaptive cruise control system that can be adjusted accordin...[Details]
MEMS sensors
京公网安备 11010802033920号
EEWORLD
