Features .......................................................................................................................................................................................1
3.2 x 2.5 mm Package Pinout .......................................................................................................................................................1
Ordering Information .....................................................................................................................................................................2
Dimensions and Patterns ― 3.2 x 2.5 mm .................................................................................................................................16
Dimensions and Patterns ― 5.0 x 3.2 mm .................................................................................................................................16
Dimensions and Patterns ― 7.0 x 5.0 mm .................................................................................................................................17
Additional Information .................................................................................................................................................................18
Revision History ..........................................................................................................................................................................19
Rev 1.05
Page 3 of 19
www.sitime.com
SiT3373
220 MHz to 725 MHz Ultra-low Jitter Differential VCXO
Electrical Characteristics
Table 2. Electrical Characteristics – Common to LVPECL, LVDS and HCSL
All Min and Max limits in the Electrical Characteristics tables are specified over temperature and rated operating voltage with standard
output termination shown in the termination diagrams. Typical values are at 25°C and nominal supply voltage.
Parameter
Output Frequency Range
Frequency Stability
Symbol
f
F_stab
Min.
220.000001
-15
-25
-35
-50
Operating Temperature Range
T_use
-20
-40
-40
-40
Supply Voltage
Vdd
2.97
2.70
2.52
2.25
Pull Range
Upper Control Voltage
Lower Control Voltage
Control Voltage Input Impedance
Control Voltage Input Bandwidth
Pull Range Linearity
Frequency Change Polarity
Input Voltage High
Input Voltage Low
Input Pull-up Impedance
Duty Cycle
Start-up Time
OE Enable/Disable Time
PR
VC_U
VC_L
VC_z
V_c
Lin
–
VIH
VIL
Z_in
DC
T_start
T_oe
70%
–
–
45
–
–
Typ.
–
–
–
–
–
–
–
–
–
3.30
3.00
2.80
2.50
Max.
725
+15
+25
+35
+50
+70
+85
+95
+105
Supply Voltage
3.63
3.30
3.08
2.75
V
V
V
V
ppm
Vdd
Vdd
MΩ
kHz
%
–
–
30%
-
55
3.0
3.8
Vdd
Vdd
kΩ
%
ms
µs
Measured from the time Vdd reaches its rated minimum value.
f = 322.265625 MHz. Measured from the time OE pin reaches
rated VIH and VIL to the time clock pins reach 90% of swing
and high-Z. See
Figure 9
and
Figure 10
Pin 2, OE
Pin 2, OE
Pin 2, OE logic high or logic low
Contact SiTime
for other input bandwidth options
See the APR (Absolute Pull Range)
Table 11.
Contact SiTime
for custom pull range options
Voltage at which maximum frequency deviation is guaranteed
Voltage at which minimum frequency deviation is guaranteed
Unit
MHz
ppm
ppm
ppm
ppm
°C
°C
°C
°C
Extended Industrial
Extended Commercial
Industrial
Condition
Accurate to 6 decimal places
Inclusive of initial tolerance, operating temperature, rated
power supply voltage, load variations, and first year aging
at 25°C, with VIN voltage at Vdd/2.
±15
ppm is only guaranteed for pull range up to
±100
ppm.
Frequency Range
Frequency Stability
Temperature Range
Voltage Control Characteristics
±25, ±50, ±80, ±100, ±150, ±200,
±400, ±800, ±1600, ±3200
90%
–
–
–
–
–
–
10
10
–
Positive Slope
–
–
100
–
–
–
–
10%
–
–
1.0
Input Characteristics
Output Characteristics
Startup and OE Timing
Rev 1.05
Page 4 of 19
www.sitime.com
SiT3373
220 MHz to 725 MHz Ultra-low Jitter Differential VCXO
Table 3. Electrical Characteristics – LVPECL Specific
Parameter
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Maximum Output Current
Output High Voltage
Output Low Voltage
Output Differential Voltage Swing
Rise/Fall Time
RMS Period Jitter
[4]
RMS Phase Jitter (random)
Symbol
Idd
I_OE
I_leak
I_driver
VOH
VOL
V_Swing
Tr, Tf
T_jitt
T_phj
–
0.220
0.270
ps
Min.
–
–
–
–
Vdd-1.15
Vdd-1.9
1.2
–
–
Typ.
–
–
0.15
–
–
–
1.6
225
1.0
Max.
97
63
–
32
Vdd-0.7
Vdd-1.5
2.0
290
1.6
Unit
mA
mA
A
mA
V
V
V
ps
ps
Condition
Excluding Load Termination Current, Vdd = 3.3V or 2.5V
OE = Low
OE = Low
Maximum average current drawn from OUT+ or OUT-
See
Figure 5
See
Figure 5
See
Figure 6
20% to 80%, see
Figure 6
f = 322.265625 MHz, Vdd = 3.3V or 2.5V
f = 322.265625 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels, includes spurs, pull range =
±100
ppm.
Temperature ranges -20 to 70 °C and -40 to 85 °C
f = 322.265625 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels, includes spurs, pull range =
±100
ppm.
Temperature ranges -40 to 95 °C and -40 to 105 °C
f = 156.25 or 322.265625 MHz, IEEE802.3-2005 10 GbE jitter
mask integration bandwidth = 1.875 MHz to 20 MHz,
all Vdd levels
f = 322.265625 MHz, Vdd = 3.3V or 2.5V
f = 322.265625 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels, includes spurs, pull range =
±100
ppm.
Temperature ranges -20 to 70 °C and -40 to 85 °C
f = 322.265625 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels, includes spurs, pull range =
±100
ppm.
Temperature ranges -40 to 95 °C and -40 to 105 °C
f = 322.265625 MHz, IEEE802.3-2005 10 GbE jitter mask
integration bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
[backcolor=white][size=4][color=#000000]1. ARM programming mode and 7 working modes[/color][/size][/backcolor] [backcolor=white][size=4][color=#000000] [/color][/size][/backcolor] [backcolor=white][si...
I. Definition
1. Pull-up means to clamp the uncertain signal at a high level through a resistor! "The resistor also acts as a current limiter"! The same applies to pull-down!
2. Pull-up is to inject c...
Switching or mixing two or more audio signals does not produce annoying clicks, which are mainly caused by connecting the FET to a low input resistance operational amplifier circuit....
[align=left][font=微软雅黑, 宋体][size=4][color=#000000][backcolor=white]The hardware single-channel design of a single-chip microcomputer application system includes two parts: one is system expansion, tha...
Now I want a DC/DC power module with full load output. The power module has 110VDC input, 24V / 8.4A output and 200W full load output. Now the analysis on resistor value selection is as follows. Since...
[size=5] TI's newly developed UCC28780 active clamp flyback controller and UCC24612 synchronous rectifier controller chipset, operating at up to 1MHz, can help reduce the size of power supplies for ta...
Circuit breaker tester (also known as switch mechanical characteristics tester) A circuit breaker may remain idle for several years, but if a fault occurs, it must gradually separate a large ampere...[Details]
The mouse is a device used to control the movement of the screen cursor. It is one of the most important external input devices of the computer and can be used in the graphic system of human-comput...[Details]
comments: 1. Eight-wire drive LCD1602B: PB0-PB7 are data lines, PD3/PD4/PD6 control RS, RW, EN of LCD1602B. 2. Set and read the internal clock of DS1302, and display it through LCD1602. 3. For this e...[Details]
According to Jiwei.com, OnePlus held a new product launch conference this evening and officially launched the OnePlus 9RT which has been preheated for a long time. In terms of appearance, the OnePl...[Details]
In the automotive field, in addition to the AUTOSAR/OSEK OS and FreeRTOS introduced above, commonly used RTOS include but are not limited to the following:
1 QNX OS
QNX is a real-time ope...[Details]
(1) What is autonomous driving? Autonomous driving is the most important function of the new generation of intelligent connected cars. Autonomous driving refers to the technology that uses computer...[Details]
I. Introduction
In many data acquisition systems such as instruments and meters, intelligent devices, etc., which are based on single-chip microcomputers, it is often necessary to realize data ex...[Details]
• View a typical test setup for a radar receiver under test at 10 GHz • Analyze critical power level accuracy drift and impact on measurement uncertainty (MU) • Model business outcomes using Keysight...[Details]
CS5269 is a solution specially designed for TYPEC to HDMI+VGA with PD3.0 4K60Hz expansion dock.
1 Introduction to CS5269
The CS5269 is a high-performance Type-C/DP1.4 to HDMI2.0b an...[Details]
The main functional test items of Keysight's power supply include: output ripple and noise, overvoltage protection cut-off time, power on and off delay, power up and down programming time, transient ...[Details]
Introduction: The functions of a vehicle-mounted command and control platform are mainly reflected in the following aspects: monitoring and displaying the technical status of the vehicle; inter-vehic...[Details]
Recently, the trillion-level new energy vehicle industry has ushered in a major policy "gift package". On November 2, the General Office of the State Council issued the "New Energy Vehicle Industry...[Details]
Hefei, China— Corning Incorporated recently held the Corning Hefei Innovation Day event with the theme of "Integrating Innovation, Forging the Future" to join hands with industry chain partners to jo...[Details]
1. Microcontroller interrupt: I found a picture of the 80C51 microcontroller as follows: Among them, the positions of P3.2 and P3.3, that is, pins 12 and 13, are marked INT0 and INT1, and those two...[Details]
Individually, each battery cell is small and may seem insignificant. However, when hundreds of these cells are connected in series and parallel, they form the backbone of an electric vehicle's powe...[Details]
DSP and ARM Processors
京公网安备 11010802033920号
EEWORLD
