1260
Vishay Foil Resistors
Bulk Metal
®
Foil Technology Precision Trimming Potentiometers,
3/8 Inch Square, RJ24 Style, Designed to Meet or Exceed the
Requirements of MIL-PRF-39035, Char. H
FEATURES
•
Temperature coefficient of resistance (TCR):
± 10 ppm/°C (- 55 °C to + 150 °C ref. at + 25 °C);through
the wiper
2)
; ± 25 ppm/°C (see table 2 for low values)
•
Load life stability: 0.1 % typical
ΔR,
1.0 % maximum
ΔR
under full rated power at + 85 °C for 10 000 h
•
Settability: 0.05 % typical; 0.1 % maximum
•
Setting stability: 0.1 % typical; 0.5 % maximum
•
Power rating: 0.25 W at + 85 °C
•
Resistance range: 5
Ω
to 10 kΩ
•
Resistance tolerance: ± 5 %, ± 10 %
•
“O” ring prevents ingress of fluids during any board
cleaning operation
•
Terminal finishes available:
tin/lead
TABLE 1 - MODEL SELECTION
*
MODEL
1260
Note:
* See figure 1
TERMINATION STYLE
W-edge mount, top adjust
X-edge mount, side adjust
AVERAGE
WEIGHT (g)
0.4
POWER RATING
at + 85 °C AMBIENT
0.25 W
NO. OF TURNS
21 ± 2
TABLE 2 - 1260 (RJ26) SERIES ELECTRICAL
SPECIFICATIONS
Temperature Coefficient of
Resistance (TCR) 50
Ω
to 10 kΩ
End-to-end
1)
Temperature Coefficient of
Resistance 5, 10 and 20
Ω
Through the
wiper
2)
± 10 ppm/°C maximum
(- 55 °C to + 150 °C,
+ 25 °C ref.)
± 20 ppm/°C
± 25 ppm/°C
0.1 % typical
ΔR
1.0 % maximum
ΔR
(under Full Rated Power
of 0.25 W at + 85 °C)
0.25 W at + 85 °C
0.05 % typical;
0.1 % maximum
0.1 % typical;
0.5 % maximum
3
Ω
typical;
10
Ω
maximum
0.25 % typical;
1.0 % maximum
1 ns without ringing
0.08 µH typical
0.5 pF typical
- 55 °C to + 150 °C
TABLE 3 - VALUES VS. TOLERANCES
STANDARD RESISTANCE VALUES
(in
Ω)
5, 10
20, 50, 100, 200, 500, 1K, 2K, 5K, 10K
STANDARD
TOLERANCE
± 10 %
±5%
Stability
Load life at 10 000 h
TABLE 4 - MECHANICAL SPECIFICATIONS
Adjustment Turns
Mechanical Stops
Internal Terminations
Case Material
Shaft Torque
Backlash
21 ± 2
Wiper idles - no discontinuity
All welded - no flux
Diallyl-phthalate: black (DAP)
3 oz. in. maximum
0.005 % typical
Power Rating
3)
Settability
Setting Stability
Contact Resistance
Variation - CRV (noise)
Hop-off
High-Frequency Operation
Rise/decay time
Inductance
Capacitance
Operating Temperature Range
Document Number: 63054
Revision: 29-Feb-08
For any questions, contact: foil@vishay.com
www.vishay.com
1
1260
Vishay Foil Resistors
Bulk Metal
®
Foil Technology Precision Trimming
Potentiometers, 3/8 Inch Square, RJ24 Style, Designed to
Meet or Exceed the Requirements of MIL-PRF-39035, Char. H
FIGURE 1 - SCHEMATIC AND DIMENSIONS
in inches (millimeters)
1260W
0.081 ± 0.010" (2.06 ± 0.25 mm)
0.080" (2.03 mm) maximum
VISHAY
0.420" (10.67 mm) maximum
0.015" (0.38 mm)
minimum
0.300" (7.62 mm) minimum
3 pins
0.024 ± 0.006" (0.61 ± 0.15 mm) diameter
3
CW
1
2
STANDARD MARKING
0.090 ± 0.005"
(2.29 ± 0.13 mm) diameter
Model No.
Date Code
Resistance Value
Tolerance
± 0.010" (± 0.25 mm)
C
0.170 ± 0.025"
(4.32 ± 0.64 mm)
0.075 ± 0.010"
(1.91 ± 0.25 mm)
0.375 ± 0.015"
(9.53 ± 0.38 mm)
0.100 ± 0.005"
(2.54 ± 0.13 mm)
0.187 ± 0.020"
(4.75 ± 0.51 mm)
1260X
0.080" (2.03 mm) maximum
0.081 ± 0.010"
(2.06 ± 0.25 mm)
0.420" (10.67 mm)
maximum
VISHAY
2
CW
Notes:
Adjustment screw 0.090" (2.29 mm)
diameter with 0.020" (0.51 mm) x
0.031" (0.79 mm) slot. model 1260
has solder plated copper terminal
pins. 0.024" (0.61 mm) diameter,
0.300" (7.62 mm) length minimum.
3
0.015" (0.38 mm)
minimum
0.300" (7.62 mm) minimum
1
3 PINS
0.024 ± 0.006" (0.61 ± 0.15 mm) diameter
± 0.010" (± 0.25 mm)
C
0.100 ± 0.005"
(2.54 ± 0.13 mm)
0.187 ± 0.020"
(4.75 ± 0.51 mm)
0.170 ± 0.025"
(4.32 ± 0.64 mm)
0.075 ± 0.010"
(1.91 ± 0.25 mm)
0.090 ± 0.005"
(2.29 ± 0.13 mm) DIA
0.375 ± 0.015"
(9.53 ± 0.38 mm)
FIGURE 2 - POWER DERATING CURVE
Percent of Rated Power
+ 100
+ 75
+ 50
+ 25
0
- 75
- 50
- 25
0
+ 25
+ 50
+ 75 + 100 + 125 + 150 + 175
+ 85 °C
Ambient Temperature °C
www.vishay.com
2
For any questions, contact: foil@vishay.com
Document Number: 63054
Revision: 29-Feb-08
1260
Bulk Metal
®
Foil Technology Precision Trimming
Vishay Foil Resistors
Potentiometers, 3/8 Inch Square, RJ24 Style, Designed to
Meet or Exceed the Requirements of MIL-PRF-39035, Char. H
TABLE 5 - COMPARISON
MIL-PRF-39035/3 CHARACTERISTIC H
4)
TEST GROUP I
Conditioning
Contact resistance variation - CRV (noise)
Immersion
TEST GROUP Ia
Visual and mechanical
Actual effective electrical travel
End resistance
Dielectric withstanding voltage - DWV
(Atmospheric and barometric pressure)
Insulation resistance
Shaft torque
Thermal shock
Setting stability
TEST GROUP II
Solderability
TEST GROUP III
Resistance temperature characteristic - TCR
Moisture resistance
Contact resistance variation - CRV (noise)
TEST GROUP IV
Settability
Shock
Setting stability
Vibration
Setting stability
Contact resistance variation - CRV (noise)
Salt spray
TEST GROUP V
Solder heat
Low-temperature operation
Setting stability
Low-temperature storage
High-temperature exposure
Setting stability
Contact resistance variation - CRV (noise)
Integrity of shaft
TEST GROUP VI
Rotational life (200 cycles)
Contact resistance variation - CRV (noise)
Terminal strength
TEST GROUP VII
Life (2000 h) at + 85 °C
Life (10 000 h) at + 85 °C
TEST GROUP VIII
Solvent resistance
Notes:
1. Maximum TCR applies to the 3 s (sigma) limit or 99.73 % of a
production lot. (Measured end-to-end with wiper off the element.)
2. Measurements of TCR through the wiper are influenced more by
setting stability and the percentage of the total resistance in use
(at the wiper) than by fundamental resistance change due to
temperature alone. The parameter shown in table 2 is a 2 s
distribution typifying the behavior of the device when used with
40 % or more of the total resistance in use.
3. Derated linearly for full power at + 85 °C to zero (0) W at
+ 150 °C. See figure 2.
4. All
ΔR’s
are measured to the tolerance specified + 0.01
Ω.
5. Whichever is greater.
Special available options:
Special marking
Power conditioning and screening operations.
Document Number: 63054
Revision: 29-Feb-08
± 1.0 %
± 3.0 % or 3
Ω
5)
No continuous stream of bubbles
No failures
10 to 25 turns
2 % or 2
Ω
5)
Per MIL-STD-202, methods 301 and 105
≥
1000 MΩ
3 oz. in. maximum
± 1.0 %
± 1.0 %
Per MIL-STD-202, method 208
± 0.005 % (± 50 ppm/°C)
± 1.0 %
3.0 % or 3
Ω
5)
± 1.0 %
± 1.0 %
± 1.0 %
± 1.0 %
± 1.0 %
3.0 % or 3
Ω
5)
No corrosion
± 1.0 %
± 1.0 %
± 2.0 %
± 1.0 %
± 3.0 %
± 2.0 %
3.0 % or 3
Ω
5)
No loosening or breakage
± 2.0 %
3.0 % or 3
Ω
5)
2 lbs.
± 3.0 %
± 5.0 %
No failures
1260 MAXIMUM
± 0.5 %
3
Ω
typical, 10
Ω
maximum
No continuous stream of bubbles
No failures
21 ± 2 turns
2
Ω
for values
≤
1 kΩ;
5
Ω
for values
≥
2 kΩ;
Per MIL-STD-202, methods 301 and 105
> 1000 MΩ
3 oz. in. maximum
± 0.5 %
± 0.5 %
Per MIL-STD-202, method 208
± 0.001 % (± 10 ppm/°C)
± 0.5 %
3
Ω
typical, 10
Ω
maximum
± 0.1 %
± 0.5 %
± 0.5 %
± 0.5 %
± 0.5 %
3
Ω
typical, 10
Ω
maximum
No corrosion
± 0.1 %
± 0.5 %
± 0.5 %
± 0.5 %
± 0.5 %
± 0.5 %
3
Ω
typical, 10
Ω
maximum
No loosening or breakage
± 2.0 %
3
Ω
typical, 10
Ω
maximum
2 lbs.
± 0.1 % typical, ± 1.0 % maximum
± 0.1 % typical, ± 1.0 % maximum
No failures
VISHAY TRIMMERS ARE INSPECTED
100 % for:
• Short-time overload
(6.25 x rated power for 5 s on; and for 30 s off - 3 cycles)
• Immersion
• Resistance tolerance check
• End resistance
• Visual-mechanical
• Dynamic tests for continuity, CRV
By sample for:
• TCR
• DWV
www.vishay.com
3
For any questions, contact: foil@vishay.com
1260
Vishay Foil Resistors
Bulk Metal
®
Foil Technology Precision Trimming
Potentiometers, 3/8 Inch Square, RJ24 Style, Designed to
Meet or Exceed the Requirements of MIL-PRF-39035, Char. H
TABLE 6 - GLOBAL PART NUMBER INFORMATION
NEW GLOBAL PART NUMBER: Y0069500R000J0L (preferred part number format)
DENOTES PRECISION
Y
VALUE
R
=
Ω
K
= kΩ
AER*
0
= standard part, tin/lead termination
1 - 999
= custom
Y
0
0
6
9
5
0
0
TOLERANCE
J
=±5%
K
= ± 10 %
M
= ± 20 %
R
0
0
0
J
0
L
PRODUCT CODE
0069
= 1260W
4069
= 1260X
PACKAGING
L
= bulk pack
FOR EXAMPLE: ABOVE GLOBAL ORDER Y0069 500R000 J 0 L:
TYPE: 1260W
VALUE: 500.0
Ω
ABSOLUTE TOLERANCE: ± 5.0 %
AER: standard part, tin/lead termination
PACKAGING: bulk pack
HISTORICAL PART NUMBER: 1260W 500R00 J B (will continue to be used)
1260W
MODEL
1260W
1260X
500R00
RESISTANCE VALUE
500R00
= 500.00
Ω
J
TOLERANCE
J
=±5%
K
= ± 10 %
M
= ± 20 %
B
PACKAGING
B
= bulk pack
Note
* Application engineering release: for non-standard requests, please contact application engineering.
www.vishay.com
4
For any questions, contact: foil@vishay.com
Document Number: 63054
Revision: 29-Feb-08
Legal Disclaimer Notice
Vishay
Disclaimer
All product specifications and data are subject to change without notice.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf
(collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein
or in any other disclosure relating to any product.
Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any
information provided herein to the maximum extent permitted by law. The product specifications do not expand or
otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed
therein, which apply to these products.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this
document or by any conduct of Vishay.
The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless
otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such
applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting
from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding
products designed for such applications.
Product names and markings noted herein may be trademarks of their respective owners.
Document Number: 91000
Revision: 18-Jul-08
www.vishay.com
1
PCB Design
京公网安备 11010802033920号
EEWORLD
