RWR Military
www.vishay.com
Vishay Dale
Wirewound Resistors, Military/Established Reliability,
MIL-PRF-39007 Qualified, Type RWR, R Level, Axial Lead
FEATURES
•
•
•
•
High temperature silicone coated
Complete welded construction
Qualified to MIL-PRF-39007
Available in non-inductive styles (type N) with Aryton-Perry
winding for lowest reactive components
•
“S” level failure rate available
Note
• “Terminal Wire and Winding” type “W” and “Z” are not listed
below but are available upon request. Please reference
MIL-PRF-39007 QPL for approved “failure rate” and “resistance
tolerance/ranges”
STANDARD ELECTRICAL SPECIFICATIONS
MILITARY MODEL
RWR81S
RWR81N
RWR82S
RWR82N
RWR80S
RWR80N
RWR71S
RWR71N
RWR89S
RWR89N
RWR74S
RWR74N
RWR84S
RWR84N
RWR78S
RWR78N
VISHAY REFERENCE
MODEL
EGS-1-80
EGN-1-80
EGS-2
EGN-2
EGS-3-80
EGN-3-80
ESS-2A
ESN-2A
ESS-2B
ESN-2B
ESS-5
ESN-5
EGS-10-80
EGN-10-80
ESS-10
ESN-10
POWER RATING
P
25 °C
W
1
1
2
2
2
2
2
2
3
3
5
5
7
7
10
10
RESISTANCE RANGE
± 0.1 %
0.499 to 1K
0.499 to 499
0.499 to 1.3K
0.499 to 649
0.499 to 3.16K
0.499 to 1.58K
0.499 to 12.1K
0.499 to 6.04K
0.499 to 4.12K
0.499 to 2.05K
0.499 to 12.1K
0.499 to 6.04K
0.499 to 12.4K
0.499 to 6.19K
0.499 to 39.2K
0.499 to 19.6K
RESISTANCE RANGE
± 0.5 %, ± 1 %
0.1 to 1K
0.1 to 499
0.1 to 1.3K
0.1 to 649
0.1 to 3.16K
0.1 to 1.58K
0.1 to 12.1K
0.1 to 6.04K
0.1 to 4.12K
0.1 to 2.05K
0.1 to 12.1K
0.1 to 6.04K
0.1 to 12.4K
0.1 to 6.19K
0.1 to 39.2K
0.1 to 19.6K
WEIGHT
(typical) g
0.21
0.21
0.23
0.23
0.34
0.34
0.90
0.90
0.70
0.70
4.2
4.2
3.6
3.6
9.0
9.0
TECHNICAL SPECIFICATIONS
PARAMETER
UNIT
RWR RESISTOR CHARACTERISTICS
Temperature Coefficient
ppm/°C ± 20 for 10
and above; ± 50 for 1.1
to 10
;
± 400 for 0.505
to 1
;
± 650 for 0.1
to 0.499
500 minimum for 2 W and smaller, 1000 minimum for 3 W and larger
Dielectric Withstanding Voltage
V
AC
5 x rated power for 5 s for 3 W size and smaller,
Short Time Overload
-
10 x rated power for 5 s for 5 W size and greater
Maximum Working Voltage
V
(P x
R)
1/2
Insulation Resistance
.
1000 M minimum dry, 100 M minimum after moisture test
Terminal Strength
lb
5 minimum for 2 W and smaller, 10 minimum for 3 W and larger
Solderability
-
Meets requirements of ANSI J-STD-002
Operating Temperature Range
°C
- 65 to + 250
GLOBAL PART NUMBER INFORMATION
Global Part Numbering example: RWR74S49R9FSB12
R
MIL TYPE
RWR71
RWR74
RWR78
RWR80
RWR81
RWR82
RWR84
RWR89
W
R
7
4
S
4
9
R
9
F
S
B
1
2
PACKAGING CODE
B12
= Bulk pack
S70
= Tape/reel
(smaller than 5 W)
S73
= Tape/reel
(5 W and higher)
BSL
= Bulk pack,
single lot date code
RSL
= Tape/reel,
single lot date code
TERMINAL WIRE AND WINDING
S
= Solderable, inductive
N
= Solderable, non-inductive
W
= Weldable, inductive
(1)
Z
= Weldable, non-inductive
(1)
RESISTANCE VALUE
3 digit significant figure,
followed by a multiplier
49R9
= 49.9
1000
= 100
1001
= 1000
TOLERANCE CODE
B
= ± 0.1 %
D
= ± 0.5 %
F
= ± 1.0 %
FAILURE RATE
M
= 1.0 %/1000 h
P
= 0.1 %/1000 h
R
= 0.01 %/1000 h
S
= 0.001 %/1000 h
(1)
Note
Note that “W” and “Z” are not listed above but are available, see MIL-PRF-39007 QPL for available resistance values.
1
For technical questions, contact:
ww2bresistors@vishay.com
Revision: 12-Sep-11
Document Number: 30203
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
RWR Military
www.vishay.com
DIMENSIONS
in inches [millimeters]
A
1.50 [38.10]
(1)
min.
Vishay Dale
B
C
MILITARY MODEL
RWR81
RWR82
RWR80
RWR71
RWR89
RWR74
RWR84
RWR78
DIMENSIONS
in inches [millimeters]
A
0.250 ± 0.031 [6.35 ± 0.787]
0.312 ± 0.016 [7.92 ± 0.406]
0.406 ± 0.031 [10.31 ± 0.787]
0.812 ± 0.062 [20.62 ± 1.58]
0.560 ± 0.062 [14.22 ± 1.58]
0.875 ± 0.062 [22.23 ± 1.58]
0.875 ± 0.062 [22.23 ± 1.58]
1.780 ± 0.062 [45.21 ± 1.58]
B
0.085 ± 0.020 [2.16 ± 0.508]
0.078 + 0.016 - 0.031 [1.98 + 0.406 - 0.787]
0.094 ± 0.031 [2.39 ± 0.787]
0.187 ± 0.031 [4.75 ± 0.787]
0.187 ± 0.031 [4.75 ± 0.787]
0.312 ± 0.031 [7.92 ± 0.787]
0.312 ± 0.031 [7.92 ± 0.787]
0.312 ± 0.031 [7.92 ± 0.787]
C
0.020 ± 0.0015 [0.508 ± 0.038]
0.020 ± 0.0015 [0.508 ± 0.038]
0.020 ± 0.0015 [0.508 ± 0.038]
0.032 ± 0.002 [0.813 ± 0.051]
0.032 ± 0.002 [0.813 ± 0.051]
0.040 ± 0.002 [1.02 ± 0.051]
0.040 ± 0.002 [1.02 ± 0.051]
0.040 ± 0.002 [1.02 ± 0.051]
Note
(1)
On some standard reel pack methods, the leads may be trimmed to a shorter length than shown.
MATERIAL SPECIFICATIONS
Element:
Copper-nickel alloy or nickel-chrome alloy,
depending on resistance value
Core:
Ceramic, beryllium oxide, steatite or alumina,
depending on power requirement
Coating:
Special high temperature silicone
Terminal and Winding:
The terminal and the winding are
identified by a letter symbol in the military type designation.
Military symbol:
S
= Solderable, inductively wound
W
= Weldable, inductively wound
N
= Solderable, non-inductively wound
Z
= Weldable, non-inductively wound
Terminals:
Solderable - Tinned Copperweld
®
Weldable - bare nickel per MIL-STD-1276, Type N-1
End Caps:
Stainless steel
Part Marking:
Source code, JAN, military PIN, date/lot code
DERATING
RATED POWER IN %
120
100
80
60
40
20
0
- 65 - 50
0
25
50
150
250
AMBIENT TEMPERATURE IN °C
PERFORMANCE
TEST
Thermal Shock
Short Time Overload
Dielectric Withstanding Voltage
Low Temperature Storage
High Temperature Exposure
Moisture Resistance
Shock, Specified Pulse
Vibration, High Frequency
Load Life
Extended Life
Terminal Strength
CONDITIONS OF TEST
MIL-STD-2.2, method 303
5 x rated power (RWR71, RWR80, RWR81, RWR89, RWR82),
10 x rated power (RWR74, RWR78, RWR84) for 5 s
500 V
rms
(RWR80, RWR81, RWR82),
1000 V
rms
(RWR71, RWR74, RWR78, RWR84, RWR89), 1 min duration
- 65 °C for 24 h
250 °C for 2000 h
MIL-STD-202, method 106
MIL-STD-202, method 213, condition 1
MIL-STD-202, method 204, condition D
2000 h at rated power, + 25 °C, 1.5 h “ON”, 0.5 h “OFF”
10 000 h at rated power, + 25 °C, 1.5 h “ON”, 0.5 h “OFF”
MIL-STD-202, method 211, condition A and C
5 pound (RWR80, RWR81, RWR82),
10 pound (RWR71, RWR74, RWR78, RWR84, RWR89)
TEST LIMITS
± (0.2 % + 0.005
) R
± (0.2 % + 0.005
) R
± (0.1 % + 0.005
) R
± (0.1 % + 0.005
) R
± (1.0 % + 0.005
) R
(2)
± (0.2 % + 0.005
) R
± (0.1 % + 0.005
) R
± (0.1 % + 0.005
) R
± (0.5 % + 0.005
) R
± (1.0 % + 0.005
) R
± (0.1 % + 0.005
) R
Note
(2)
For resistance values above 100
,
test limit is ± 1.0 %.
Revision: 12-Sep-11
2
For technical questions, contact:
ww2bresistors@vishay.com
Document Number: 30203
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
Legal Disclaimer Notice
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree
to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and
damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay
or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to
obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Document Number: 91000
Revision: 11-Mar-11
www.vishay.com
1
Talking
京公网安备 11010802033920号
EEWORLD
