EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

1375-2-50-2-1-2

Description
Board Connector, 50 Contact(s), 2 Row(s), Male, Right Angle, 0.05 inch Pitch, Surface Mount Terminal, Locking, Receptacle
CategoryThe connector    The connector   
File Size111KB,1 Pages
ManufacturerConexcon Group
Environmental Compliance
Download Datasheet Parametric View All

1375-2-50-2-1-2 Overview

Board Connector, 50 Contact(s), 2 Row(s), Male, Right Angle, 0.05 inch Pitch, Surface Mount Terminal, Locking, Receptacle

1375-2-50-2-1-2 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerConexcon Group
Reach Compliance Codeunknown
body width0.134 inch
subject depth0.305 inch
body length1.25 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationSN
Contact completed and terminatedTIN
Contact point genderMALE
Contact materialBRASS
contact modeRECTANGULAR
Contact resistance20 mΩ
Contact styleSQ PIN-SKT
Dielectric withstand voltage300VAC V
Durability50 Cycles
Insulation resistance1000000000 Ω
Manufacturer's serial number1375
Plug contact pitch0.05 inch
Match contact row spacing0.05 inch
Installation option 1LOCKING
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded2
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
PCB contact patternRECTANGULAR
PCB contact row spacing2.4892 mm
Rated current (signal)1 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal pitch1.27 mm
Termination typeSURFACE MOUNT
Total number of contacts50
Could you please tell me how to find the maximum output duty cycle of a DCDC buck IC from its technical manual?
Some DCDC chip technical manuals directly state the maximum duty cycle that can be output, while others do not. Where can I find it in the technical documentation?...
dianhang Switching Power Supply Study Group
2. [Learning LPC1768 library functions] Keystroke experiment
The key experiment is essentially to operate the GPIO pins of Lpc1768, but unlike the LED experiment, the key experiment is to read the GPIO pin value. As can be seen from the figure below, when the k...
cxmdz NXP MCU
How to change UDP point-to-point communication to UDP broadcast communication
I used the Zhengdian Atom board to test the network port program, and the UDP point-to-point communication was successful. I want to change to broadcast mode and set the target IP address to 255.255.2...
chenbingjy stm32/stm8
Design of a USB reader based on embedded system
[size=4][color=#222222][font="] With the rapid development of USB technology and flash memory technology, the speed and capacity of mobile storage devices are changing with each passing day. However, ...
Aguilera Microcontroller MCU
Understand the development principle of WiFi endoscope HD wireless camera in wireless communication module function in one article
When it comes to wifi video transmission, do you first think of the need for a core module with video compression SOC, a huge system, a complex remote server, etc., and the excessive budget cost makes...
沉迷物联网WiFi的小哥 Innovation Lab
Analysis of common problems in TWS headset design
Some common problems that are easy to occur during the design process:The two CC1 and CC2 pins of the TYPE-C USB of the charging case cannot be short-circuited together, and each must be connected to ...
Fred_1977 Analog electronics

Technical ResourceMore

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号