SMT Power Inductors
Round Wire Coils - PG1083NL series
Inductance Range: 1.0uH to 50.0uH
Current Rating: up to 70Apk
Footprint: 21.7mm x 21.5mm Max
Electrical Specifications @ 25°C — Operating Temperature -40°C to +130°C
1
Saturation
5
Controlled Electrical Specs.
Current Isat
Heating Current
6
3
(A TYP)
Irated
Idc
(A)
Inductance
DCR
4
(A TYP)
(mΩ)
@ 0Adc
25°C
100°C
MAX
(μH
±W
20%)
40
1.4
1.00
70
65
40
40
1.4
1.50
52
45
40
34
1.8
2.20
46
37
34
28
2.2
3.30
37
33
28
26
2.8
4.70
30
24
26
22
3.8
6.80
26
20
22
17.5
6.0
10.5
22.5
18
17.5
14
9.2
15.2
18.5
14
14.0
11
15.0
24.5
14.5
12
11.0
9
21.5
32.0
12.5
10
9.0
7.4
32.6
50.0
10.0
8.5
7.4
7.
Height: 12.5mm Max
No Thermal Aging
Part Number
Inductance
2
@ Irated
(μH Typical)
0.95
1.35
1.95
2.70
4.10
6.10
8.60
12.6
21.0
27.9
45.2
Core Loss Factor
7
(K2)
17.9
26.8
29.5
35.4
50.4
52.1
62.6
74.1
93.9
107.3
134.1
Size X
(REF.)
Height
(MAX.)
PG1083.102NL
PG1083.152NL
PG1083.222NL
PG1083.332NL
PG1083.472NL
PG1083.682NL
PG1083.103NL
PG1083.153NL
PG1083.253NL
PG1083.323NL
PG1083.503NL
0.098
[2.50]
BOTTOM
VIEW A
0.417
[10.6]
0.054
[1.40]
BOTTOM
VIEW B
0.492
[12.50]
Notes:
1.
Actual temperature of the component during system operation (ambient plus temperature rise) must be
within the standard operating range.
2.
Inductance at Irated is a typical inductance value for the component taken at rated current.
3.
The rated current as listed is either the saturation current (@ 25°C) or the heating current depending on
which value is lower.
4.
The DCR of the part is measured at an ambient temperature of 20°C±3°C from point a to b as shown below
on the mechanical drawing.
5.
The saturation current, Isat, is the current at which the component inductance drop by 20% (typical) at an
ambient temperature. This current is determined by placing the component in the specified ambient envi-
ronment and applying a short duration pulse current (to eliminate self-heating effect) to the component.
6.
The heating current, Idc, is the DC current required to raise the component temperature by approximately
40°C. The heating current is determined by mounting the component on a typical PCB and applying current
for 30 minutes. The temperature is measured by placing the thermocouple on top of the unit under test.
Take note that the components’ performance varies depending on the system condition. It is suggested
that the component be tested at the system level, to verify the temperature rise of the component during
system operation.the components’ performance varies depending on the system condition. It is suggested
that the component be tested at the system level, to verify the temperature rise of the component during
system operation.
8.
9.
10.
Core loss approximation is based on published core data (at 100°C):
Core Loss = K1 * (f)
1.378
* (K2*ΔI)
2.864
in mW
K1 = 1.01E-9
f = switching frequency in KHz
K1 & K2 = core loss factors
ΔI=
delta I across the component in Ampere
K2*ΔI=one half of the peak to peak flux density across the component in Gauss
Unless otherwise specified, all testing is made at 100kHz, 0.1Vac
Optional Tape & Reel packaging can be ordered by adding a “T” suffix to the part number (i.e. PG1083.682NL
becomes PG1083.682NLT). Pulse complies with industry standard tape and reel specification EIA481. The
tape and reel for this product has a width (W=44.0mm), pitch (Po=32.0mm). The depth (Ko) has two types:
1) 10.6 mm for parts with height of 10.6mm max, 120 pieces/reel; 2) 12.9mm for the parts of 12.5mm max,
100 pieces/reel.
The core is a conductive material so care should be taken when mounting this component over an exposed
via or if the voltage across the terminals exceeds 24V. Trickle current through the core material may gener-
ate additional losses and potential overheating. Please contact Pulse to discuss an alternative solution if
required.
PG1083.XXXNL
.854MAX
[21.70]
Mechanicals
(.571[14.50])
Schematic
(.571[14.50])
SIZE X
SIZE X
.091[2.30]MIN
1
1
2
.091[2.30]MIN
1
PG1083.XXXNL
DATE CODE CTRY MFG
.846MAX
[21.50]
2
2
(.094[2.40])
(.098[2.50])
3
(.098[2.50])
3
BOTTOM VIEW B
.571[14.50]
(.094[2.40])
3
Weight..........................18.6
grams
Tape and Reel....................100/tray
Dimensions:
Inches
mm
0.01
0,25
TOP VIEW
BOTTOM VIEW A
.197[5.00]
HEIGHT MAX.
.157[4.00]
a
b
d
.006[.15]
.689[17.50]
.157[4.0]
.157[4.00]
Unless otherwise specified, all tolerences are
±
SUGGESTED LAND PATTERN
1
power.pulseelectronics.com
P716.C (05/17)
http://www.power.pulseelectronics.com/contact
SMT Power Inductors
Round Wire Coils - PG1083NL series
682NL @ 100C
682NL @ 25C
472NL @ 100C
332NL @ 100C
472NL @ 25C
222NL @ 100C
152NL @ 100C
102N L@ 25C
332NL @ 25C
222NL @ 25C
152NL @ 25C
102NL @ 100C
503NL @ 100C
503NL @ 25C
323NL @ 100C
323NL @ 25C
253NL @ 100C
253NL @ 25C
153NL @ 100C
103NL @ 100C
153NL @ 25C
103N L@ 25C
For More Information
Pulse Worldwide
Pulse Europe
Headquarters
Pulse Electronics GmbH
15255 Innovation Drive Ste 100 Am Rottland 12
San Diego, CA 92128
58540 Meinerzhagen
U.S.A.
Germany
Pulse China Headquarters
Pulse Electronics (ShenZhen) CO., LTD
D708, Shenzhen Academy of
Aerospace Technology,
The 10th Keji South Road,
Nanshan District, Shenzhen, P.R.
China 518057
Tel: 86 755 33966678
Fax: 86 755 33966700
Pulse North China
Room 2704/2705
Super Ocean Finance Ctr.
2067 Yan An Road West
Shanghai 200336
China
Tel: 86 21 62787060
Fax: 86 2162786973
Pulse South Asia
135 Joo Seng Road
#03-02
PM Industrial Bldg.
Singapore 368363
Pulse North Asia
3F, No. 198
Zhongyuan Road
Zhongli City
Taoyuan County 32068
Taiwan
Tel: 886 3 4356768
Fax: 886 3 4356823
Tel: 858 674 8100
Fax: 858 674 8262
Tel: 49 2354 777 100
Fax: 49 2354 777 168
Tel: 65 6287 8998
Fax: 65 6280 0080
Performance warranty of products offered on this data sheet is limited to the parameters specified. Data is subject to change without notice. Other brand and product names mentioned herein may
be trademarks or registered trademarks of their respective owners. © Copyright, 2017. Pulse Electronics, Inc. All rights reserved.
2
power.pulseelectronics.com
P716.C (05/17)
http://www.power.pulseelectronics.com/contact
京公网安备 11010802033920号
EEWORLD
