NPP2-T1262.15OHM0.5%10PPM datasheet, PDF

NPP2-T1262.15OHM0.5%10PPM: DescriptionFixed Resistor, Thin Film, 5W, 2.15ohm, 500V, 0.5% +/-Tol, -10,10ppm/Cel, 3312; CategoryPassive components The resistor; File Size816KB，3 Pages; ManufacturerVishay; Websitehttp://www.vishay.com; Environmental Compliance

Download Datasheet Parametric View All

NPP2-T1262.15OHM0.5%10PPM Overview

Fixed Resistor, Thin Film, 5W, 2.15ohm, 500V, 0.5% +/-Tol, -10,10ppm/Cel, 3312

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
Maker	Vishay
Reach Compliance Code	compliant
ECCN code	EAR99
structure	Rectangular
Lead length	12 mm
lead spacing	5.1 mm
Manufacturer's serial number	NPP2-T126
Number of terminals	2
Maximum operating temperature	155 °C
Minimum operating temperature	-55 °C
Package height	15 mm
Package length	8.5 mm
Package shape	RECTANGULAR PACKAGE
Package form	Radial
Package width	3.1 mm
Rated power dissipation(P)	5 W
resistance	2.15 Ω
Resistor type	FIXED RESISTOR
series	NPP2-T126
size code	3312
technology	THIN FILM
Temperature Coefficient	-10,10 ppm/°C
Tolerance	0.5%
Operating Voltage	500 V

[RISC-V MCU CH32V103 Review] - 2: Making an LED flash is not easy: [i=s]This post was last edited by MianQi on 2021-1-28 11:56[/i]Let's look at the wiring first (the tutorial says to directly connect PinA0\PinA1 and LED1\LED2 with jumpers. I'm not used to doing this,...; MianQi Domestic Chip Exchange

SensorTile.box uses air pressure sensors to analyze environmental changes: After the SensorTile.box is flashed with DataLogExtended firmware, the sensor output data waveform can be directly viewed using Unicleo-GUI The following is the data obtained by using the air pressure...; littleshrimp MEMS sensors

Integrated circuit detection method: Editor's note: Although there are ways to replace integrated circuits, disassembly is troublesome after all. Therefore, before disassembly, you should accurately determine whether the integrated circu...; fighting Test/Measurement

When using an oscilloscope probe to measure the AC waveform between the two ends of a component, how should the probe ground wire be connected?: When using an oscilloscope probe to measure the AC waveform between the two ends of a component, if the peak value of the AC voltage of the probe ground wire is 180V and the minimum value is -180V, th...; 深圳小花 MCU

【ST NUCLEO-H743ZI Review】（2）Ethernet Test: [i=s]This post was last edited by dsjsjf on 2019-3-1 11:15[/i] [url=https://bbs.eeworld.com.cn/elecplay/content/103]The development board ST NUCLEO-H743ZI evaluated in this event is provided by STMicr...; dsjsjf stm32/stm8

TI.com Online Purchasing Special (Smart Building) has a limited time offer, with discounts as low as 30%!: TI.com is a convenient and direct shopping experience. Here, you can get a large number of genuine products in stock and enjoy great online prices*. From the early design stage to the mass production ...; arui1999 TI Technology Forum

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components