EEWORLDEEWORLDEEWORLD

Part Number

Search

FHR4-802162.43OHMSD0.1%

Description
Fixed Resistor, Metal Foil, 1200W, 2.43ohm, 0.1% +/-Tol, -15,15ppm/Cel
CategoryPassive components    The resistor   
File Size963KB,6 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Environmental Compliance  
Download Datasheet Parametric View All

FHR4-802162.43OHMSD0.1% Overview

Fixed Resistor, Metal Foil, 1200W, 2.43ohm, 0.1% +/-Tol, -15,15ppm/Cel

FHR4-802162.43OHMSD0.1% Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerVishay
Reach Compliance Codecompliant
ECCN codeEAR99
structureRectangular
JESD-609 codee3
Manufacturer's serial numberFHR4-80216
Number of terminals2
Maximum operating temperature130 °C
Minimum operating temperature-40 °C
Package height216 mm
Package length80 mm
Package shapeRECTANGULAR PACKAGE
Package formPCB Mount
Package width15 mm
Rated power dissipation(P)1200 W
resistance2.43 Ω
Resistor typeFIXED RESISTOR
seriesFHR4-80216
technologyMETAL FOIL
Temperature Coefficient-15,15 ppm/°C
Terminal surfaceMatte Tin (Sn)
Tolerance0.1%
FHR 2/4 8065 80110 80216 80320 80370
Powertron
Resistances from 0.001Ohm to 500Ohms
Power Rating to 2500Watt
Resistance Tolerances to ±0.1%
TCR to ±15ppm/K
Load Stability to 0.1%
Very Low Inductance (<50nH)
SPECIFICATIONS
Type
Resistance Range
Power rating
free air 25°C
with heatsink
Thermal Resistance Rthj-c
Tolerances (4 terminal version)
from 0.001 Ohms
from 0.01 Ohms
from 0.02 Ohms
Tolerances (2 terminal version)
Stability
Temperature Coefficient (4 terminal version)
8065
0.001 to 400Ohms
24 W
350 W
0.16 K/W
80110
32 W
600 W
0.09 K/W
80216
60 W
1200 W
0.04 K/W
80320
80 W
2000 W
0.026 K/W
80370
90 W
2500 W
0.022 K/W
0.001 to 500Ohms
0.5% / 1% / 2% / 5%
0.25% / 0.5% / 1% / 2% / 5%
0.1% / 0.25% / 0.5% / 1% / 2% / 5%
0.5% / 1% / 2% / 5%
0.1% / 0.2% / 0.5%
(depends on stress)
±15ppm/K (20 to 60°C)
from R ≤ 0.02 Ohms ±20ppm/K (20 to 60°C)
from R ≤ 0.01 Ohms ±30ppm/K (20 to 60°C)
±15ppm/K (20 to 60°C)
±50ppm/K (-40 to 130°C)
R ≤ 0.2 Ohms TCR see table A next page
60 A
upon request special cable up to 250 A
< 50 nH
500 pF
850 pF
1.7 nF
< 0.1µV/K
-40 to 130°C
CuNiMn-Foil
anodized aluminium
anodized aluminium
Cu-Cable / 4mm² / 500mm lenght
(other upon request / AWG possible)
2 or 4
2.5 nF
2.9 nF
1.5 kVDV (higher upon request)
Temperature Coefficient (2 terminal version)
Max. Current
Inductivity
Capacity against housing
Insulation Strenght
Thermal EMF
Operating Temperature Range
Resistor Material
Substrate
Housing
Connector Material
Terminals
Ordering Information
Part Number - Resistance - Contact - Tolerance
FHR 4-80216 1.0 Ohms D 1%
Document Number: 64202
Revision: 20-09-10
For technical questions, contact:
powertron@vishaypg.com
www.powertron.de
1
Simple square wave generator based on 51 single chip microcomputer
A simple square wave signal generator that can adjust the frequency with one button. The LED lights up when the frequency is out of range. The frequency range is 100-1000hz. #include reg52.hsbit PWMOU...
fish001 Microcontroller MCU
MSP430fr6989 serial port DMA sending experimental routine
In this example, P2.0 and P2.1 of MSP430fr6989 are selected as serial ports UCA0TXD and UCA0RXD; (There is not much code, mainly for register operations, and it is written in the main.c file in a hurr...
fish001 Microcontroller MCU
When designing PCB, how to consider electromagnetic compatibility EMC/EMI, specifically...
[size=4][b]Question[/b][/size] [size=4]How to consider electromagnetic compatibility (EMC/EMI) when designing PCB? What specific aspects should be considered? What measures should be taken? [/size]...
ohahaha PCB Design
How to measure the PWM generated by msp430f149 with an oscilloscope
I connected the red test lead to pin 46 (the pin that generates PWM) and the black test lead to gnd on the board, but the oscilloscope did not display a waveform and the PWM indicator light was flashi...
q胡= TI Technology Forum
EEWORLD University ---- Signal Processing on MSP430 16-bit MCU
Signal Processing on MSP430 16-bit MCU : https://training.eeworld.com.cn/course/4989...
wanglan123 Talking
What should I do if the segment code LCD screen has too many segments and the pins cannot be placed?
[align=left][color=rgb(0, 0, 0)][font=Verdana, Arial, Helvetica, sans-seri][size=14px] There are three common ways to connect segment code LCD screens: 1. Metal pins 2. Zebra stripes 3. FPC, etc.; of ...
晶拓 Integrated technical exchanges

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号