1241.1120.7.005 datasheet, PDF

Datasheet> All Categories > Mechanical and electronic products> switch> 1241.1120.7.005

1241.1120.7.005: DescriptionPushbutton Switch, SPST, Off-on-(off), Momentary, 0.05A, 24VDC, 4 PCB Hole Cnt, Solder Terminal, Through Hole-straight; CategoryMechanical and electronic products switch; File Size134KB，4 Pages; ManufacturerSCHURTER; Websitehttp://www.schurterinc.com/; Environmental Compliance

Download Datasheet Parametric View All

1241.1120.7.005 Overview

Pushbutton Switch, SPST, Off-on-(off), Momentary, 0.05A, 24VDC, 4 PCB Hole Cnt, Solder Terminal, Through Hole-straight

1241.1120.7.005 Parametric

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
Maker	SCHURTER
Reach Compliance Code	compliant
ECCN code	EAR99
Actuator angle
Actuator length	0.006 inch
Actuator material	POLYCARBONATE
Actuator type	PUSHBUTTON
Other features	NON LUMINOUS,W/LEGEND
body height	9.4996 mm
Body length or diameter
Casing diameter
Nozzle length
center contact material	BRASS
Center contact plating	GOLD
Maximum contact current (DC)	0.05 A
Contact (DC) maximum rated power R load	0.36VA@24VDC
Contact (DC) maximum rated R load	0.05A@24VDC
Contact function	OFF-ON-(OFF)
Contact resistance	0.05 mΩ
contact time	BREAK-BEFORE-MAKE
Maximum contact voltage (DC)	24 V
Electrical life	1000000 Cycle(s)
End contact material	BRASS
End contact plating	GOLD
Insulation resistance	100000000 Ω
insulator material	POLYETHERSULPHONE
JESD-609 code	e3
Manufacturer's serial number	MCS
Installation features	THROUGH HOLE-STRAIGHT
Maximum operating temperature	85 °C
Minimum operating temperature	-25 °C
PCB hole count	4
surface mount	NO
Switch action	MOMENTARY
switch function	SPST
Switch type	PUSHBUTTON SWITCH
Terminal surface	Matte Tin (Sn)
Terminal length	0.126 inch
Termination type	SOLDER

Preview

Download Datasheet

View All

Switches in momentary action MTG, MCS, MTP and MTL

/ "

Models

Construction

Dimensions

Circuit diagram Drilling diagram

illuminated

2.54

Pol LED

MTG 3/4"

7.62

10.16

7.62

non-illuminated

illuminated

2.54

Pol LED

MCS 3/4"

7.62

10.16

7.62

non-illuminated

MTP 3/4"

illuminated

MTL 3/4"

Indicator

2.54

10.16

7.62

Pol LED

Bohrplan-Raster

1/20" = 1,27 mm

Z= drilling for location pins

drilling diagram

1/20" = 1,27 mm

Printmount Line

7.62

Recommended Resources

Infrared light signal receiving circuit

HI-FI amplifier 01 made by STK4040x1

Proximity switch circuit

Inverter power circuit

Single potentiometer gain-adjustable op amp

Lebao, Regal CFXB-4 series, CFXB-IH series thermal insulation automatic rice cooker circuit diagram

[Environmental Expert's Smart Watch] Part 13: Storing various data in EEPROM: [i=s]This post was last edited by w494143467 on 2021-6-27 15:56[/i]1 Introduction Since it is a watch, it must have the function of storing data. There is an onboard [N24RF64] chip, which can be used ...; w494143467 onsemi and Avnet IoT Innovation Design Competition

Behavioral modeling sequential logic circuit (two-input AND gate) source code and test code: Source code:module and_gate1(clk, a, b, s);input clk;input a;input b;output reg s;//Behavioral modeling sequential logic circuit (two-input AND gate)always @ (posedge clk) //Rising edge triggeredbegin...; zxopenljx FPGA/CPLD

Hardware testing method for TI-CC chip: Brief description Forced to do something that is meaningless to the current direction, we can only grab some meaning from it.Based on TI's test software smartRF studio, the hardware needs to reserve V...; 火辣西米秀 Wireless Connectivity

Why does Unico prompt that STEVAL-MKI197V1 is not supported? --- Solved: [i=s]This post was last edited by a media student on 2020-4-12 22:31[/i]I got the board today and downloaded the unico software, but it prompted the following error:Please give me some pointers..Thank...; 传媒学子 ST MEMS Sensor Creative Design Competition

Is the digital-to-analog configuration of a certain pin of STM32 related to the output? Do I need to set the output register of this pin when outputting?: Is the digital-to-analog configuration of a certain pin of STM32 related to the output? Do I need to set the output register of this pin when outputting?...; 深圳小花 stm32/stm8

EEWORLD University ---- Microprocessor and Embedded System Design University of Electronic Science and Technology of China: Microprocessor and Embedded System Design University of Electronic Science and Technology of China : https://training.eeworld.com.cn/course/5402...; 木犯001号 MCU

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components