REVISION S
FJ-XX-X-XX-X
No OF POSITIONS
-05, -10, -15, -20, -25, -30
STRIP LENGTH
-2: .079 [2.00]
*-4: .157 [4.00]
-6: .236 [6.00]
STYLE
LENGTH
**-S: SINGLE ENDED
-D: DOUBLE ENDED
-XX: "XX" INCHES .125 [3.18] INCH
-R: REVERSE STIFFENER
(-S STYLE 2.500 [63.50] MIN)
(-D & -R STYLE 2.000 [50.80] MIN)
* = RECOMMENDED MATING WITH FC1
** = AS OF 1/1/11, -S (SINGLE ENDED) ONLY
AVAILABLE TO EXISTING CUSTOMERS,
ALL OTHERS WILL BE ASP`s.
DO NOT
SCALE FROM
THIS PRINT
C3
LENGTH (SPECIFY IN -XX INCHES .125 [3.18]
FC-XX-1.0
.03 0.7 REF
(No. OF POS x .03937 [1.0000])
+.03937 [1.0000] .010 [.25]
(SEE NOTE 3)
2 MAX SWAY
(TYP)
C1
{No. OF POS x .03937 [1.0000]}
+ .03937 [1.0000] .005 [.13]
(SEE NOTE 2)
(No. OF POS. -1) x .03937
[1.000]
"C" .015 [.38] (SEE TABLE 1)
SECTION "A"-"A"
.01 0.3 REF
.005 0.13 (TYP)
.0256±.008 0.650±0.20
C6
(TO BE MEASURED AT
BASE OF EXPOSED LEAD) S
.004 0.10 REF
"A"
.021 0.52 REF
HAND BUILT (SEE NOTE 6)
-S: SINGLE ENDED
(FJ-10-S-XX-2 SHOWN)
FIG 1
.207 5.26
REF
"A"
C2
.012±.002 0.30±0.05
S
FS-20
.003 0.08 REF
.01 0.2 REF
.0155 0.393 REF
FIG 4
.100 2.54
REF
"C" .030 [.76]
(SEE TABLE 1)
MACHINE BUILT (SEE NOTE 6)
-S: SINGLE ENDED
(FJ-10-S-XX-2 SHOWN)
SAME AS FIG 1 EXCEPT WHERE SHOWN
NOTES:
1.
REPRESENTS A CRITICAL DIMENSION.
2. MEASURE WHERE STIFFENER AND CABLE ARE ATTACHED.
3. MEASURED ALONG LENGTH OF CABLE, EXCEPT WHERE STIFFENER
IS ATTACHED TO CABLE.
4. NOTE DELETED.
5. STIFFENER IS TRIMMED TO CORRECT WIDTH.
6. HAND BUILT PARTS USE A BLUE STIFFENER., MACHINE BUILT PARTS
USE A BLACK STIFFENER.
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
DECIMALS
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
.XX: .01 [.25]
2
.XXX: .005 [.13]
.XXXX: .0020 [.050]
MATERIAL:
ANGLES
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail: info@SAMTEC.com
code: 55322
DESCRIPTION:
DO NOT SCALE DRAWING
SHEET SCALE: 4:1
F:\DWG\MISC\MKTG\FJ-XX-X-XX-X-MKT.SLDDRW
CONDUCTORS: TIN PLATED COPPER
SURFACE FINISH EITHER BRIGHT ACID TIN (99.9% SN)
OR MATTE TIN (95.5% SN, 3.5% AG, 1% CU)
INSULATION: POLYESTER
STIFFENER: POLYESTER
.03937 [1.0000] FLEX CABLE JUMPER
DWG. NO.
FJ-XX-X-XX-X
3/29/99
SHEET
1
OF
2
BY:
KEVIN B
REVISION S
FC-XX-1.0
LENGTH
(SPECIFY IN -XX INCHES .125 [3.18])
"C" .015 [.38]
(SEE TABLE 1)
FOR -S: ("XX" LENGTH + .591 [15.16]) .050 [1.27]
FOR -D & -R: ("XX" LENGTH + 1.181 [30.00]) .050 [1.27]
"C" .015 [.38]
(SEE TABLE 1)
IN-PROCESS 1
SEE NOTE 5
FS-20
FIG. 2
-D: DOUBLE ENDED
(SAME AS FIG. 1, UNLESS STATED)
.43 11.0
LENGTH
(SPECIFY IN -XX INCHES .125 [3.18]
FC-XX-1.0
"C" .015 [.38]
(SEE TABLE 1)
FS-20
C4
1.0225±.0075 25.970±0.191
.413±.030 10.49±0.76
FS-20
"C" .015 [.38]
(SEE TABLE 1)
-R: REVERSE STIFFENER
(SAME AS FIG 1, UNLESS STATED)
C5
FIG 3
.207±.005 5.25±0.13
.787 20.00
FS-20
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
(TYP ON BOTH ENDS FOR -D & -R STYLES)
IN-PROCESS 2
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail: info@SAMTEC.com
code: 55322
DESCRIPTION:
DWG. NO.
DO NOT SCALE DRAWING
SHEET SCALE: 3:1
.03937 [1.0000] FLEX CABLE JUMPER
FJ-XX-X-XX-X
3/29/99
SHEET
2
OF
2
F:\DWG\MISC\MKTG\FJ-XX-X-XX-X-MKT.SLDDRW
BY:
KEVIN B
京公网安备 11010802033920号
EEWORLD
