(5 ±1 seconds and charge/discharge not exceeding 50 mA)
5% (6.3 and 10 V), 3.5% (16 and 25 V) and 2.5% (50 to 250 V)
See Insulation Resistance Limit Table
(Rated voltage applied for 120 ±5 seconds @ 25°C)
Parameters/Characteristics
Regarding aging rate: Capacitance measurements (including tolerance) are indexed to a referee time of 1,000 hours.
To obtain IR limit, divide MΩ-µF value by the capacitance and compare to GΩ limit. Select the lower of the two limits.
Capacitance and dissipation factor (DF) measured under the following conditions:
1 kHz ±50 Hz and 1.0 ±0.2 Vrms if capacitance ≤ 10 µF
120 Hz ±10 Hz and 0.5 ±0.1 Vrms if capacitance > 10 µF
Note: When measuring capacitance it is important to ensure the set voltage level is held constant. The HP4284 and Agilent E4980 have a feature known as
Automatic Level Control (ALC). The ALC feature should be switched to "ON."
A key property of a semiconductor is its bandgap, the energy required to bring electrons into a conducting state. Wide bandgap (WBG) enables higher power, higher switching speed transistors, and WBG d...
Dear seniors, I chose an AD/DC module to output 12V, but after measuring the output with an oscilloscope, I found that the noise was very large, 50mV ripple plus 500mV burr. I further tested only the ...
This blog introduces the principle of large integers in PTHonhttps://tenthousandmeters.com/blog/python-behind-the-scenes-8-how-python-integers-work/...
During the project development process, developers want to encapsulate some core codes for the purpose of protecting core algorithms, so that other users cannot view the specific code implementation d...
(Image source: Laser4Surf official website) As the trend of electric travel becomes increasingly obvious, the demand for batteries will increase in the future. People need batteries that are more...[Details]
In the near future, fully autonomous vehicles are expected to significantly improve automotive safety and transportation efficiency. However, to achieve this goal, automotive OEMs must ...[Details]
In recent years, with the continuous improvement of the degree of social informatization, the amount of information exchange has exploded, and people are no longer limited to the pursuit of wirele...[Details]
EFP (Electronic Field Production) is a method of on-site program production, which integrates audio and video equipment into standard flight cases of different specifications and transports them to...[Details]
Record the content composition and principles of some simple ARM image files.
1. The composition of ARM image files (axf and bin files).
ARM is a 32-bit processor with a 32-bit address width, so ...[Details]
This 7½-digit 2010 Series low-noise multimeter combines cost-effectiveness with high resolution to test high-precision sensors, transducers, A/D and D/A converters, voltage regulators, reference sour...[Details]
The trend of automobile electrification is irreversible, and even the top supercar brand Ferrari has begun to explore electric vehicles. Ferrari is synonymous with performance, but the brand has be...[Details]
On the 15th, the Energy Storage Branch of the Zhejiang Energy Industry Federation (hereinafter referred to as the Energy Storage Branch) was established in Hangzhou. It was formed by more than 60 ente...[Details]
1 Introduction Conductivity testing technology is widely used in chemical, biological, medical, environmental protection and other fields, and is one of the important testing methods for physical pro...[Details]
The InvenSense SmartSonicTM ICU-10201 high-performance ultrasonic ToF sensor features a powerful embedded processor and expanded memory to implement complete application algorithms on-chip
...[Details]
In the past 200 years, human science and technology have advanced faster than any other period in history. In the automotive field, we have not witnessed the birth of fuel vehicles, but we are witnes...[Details]
1 Introduction
RTU (Remote Terminal Unit) is a remote measurement and control terminal, which is a terminal measurement and control unit of the monitoring, supervisory control and data acquisi...[Details]
Challenge: Use PXI control boards and LabVIEW software to build a relatively complete PCB functional test (FCT) system. This system can be used to perform comprehensive and fully automatic tests on...[Details]
I am using the OK6410 development board, which comes with two kernels (2.6.32 and 3.0.1 have been tested)
First, let’s talk about how to make a logo:
Linux Logo Maker: LogoMaker.tgz 4.7MB...[Details]
Power technology
京公网安备 11010802033920号
EEWORLD
