VOLTAGE CONTROLLED
CRYSTAL OSCILLATORS
HCMOS/TTL 5V
FULL SIZE D.I.L.
M package
M6001 thru M6007
M6021 thru M6023
HALF SIZE D.I.L.
H package
H6001 thru H6007
H6021 thru H6023
Thru-Hole/Gull Wing
Industrial: -40º to +85ºC
1 KHz to 150 MHz
GUARANTEED CAPTURE RANGE/ABSOLUTE PULL RANGE
Guaranteed Capture Range (GCR) and Absolute Pull Range (APR) are terms often used interchangeably.
MF's Guaranteed Capture Range (GCR) is defined as the minimum guaranteed frequency deviation or "pull"
(in ppm) around the nominal frequency, with all effects of temperature, variations in VDD and load taken into
account. This amount of absolute frequency deviation is available under all operating conditions for
modulation or capturing other signals. No additional frequency capture allowances are necessary.
FEATURES
•
Industrial temperature range of -40 to +85ºC allows for use in harsh environmental conditions
•
Excellent incremental and best-straight-line linearity
•
Start-up time is less than 5ms
•
Each unit is ATE-tested to guarantee full compliance with all electrical specifications
TYPICAL APPLICATIONS
•
Phase locked loops and data acquisition projects, including:
– xDSL customer premise equipment
– Cable modems
– ATM/SONET/SDH
Description
These thru-hole VCXOs generate a 5 volt
HCMOS/TTL frequency output which is
controlled ("pulled") by an input voltage.
MF Electronics' VCXO specification
defines not only the end-point frequency/
voltage parameters, but also the center
voltage at which the nominal frequency
is achieved.
CONNECTIONS
Full Size
Pin 1. Control Voltage, V
C
Pin 4.
Pin 5.
Pin 7. Ground & Case
Pin 8. Output
Pin14. +5V, V
DD
Half Size
Control Voltage, V
C
Ground & Case
Output
+5V, V
DD
DOT
DENOTES
PIN 1
DOT
DENOTES
PIN 1
DOT
DENOTES
PIN 1
.800 – .005
.52 MAX
SQUARE
.200 MAX
.215 MAX
.018 – .001
.060 TYP
.300 – .005
.400
.600 – .005
Pin 1
.100 – .005
Pin 7
.300 –. 005
.500 – .005
.150
Pin 14
Pin 8
.250 MAX
8
5
.008/025 .15 MIN
.018
.300
Pin 1
1
4
.300
Pin 14
.2 MAX
.160
.2
MAX
.018 – .001
.600 – .005
Pin 7
.520 – .005
.300 –. 005
Pin 8
GLASS INSULATORS (4)
on .48 x .18 ctrs.
1
8
DOT
DENOTES
PIN 1
.800 – .005
.52 MAX
SQUARE
.200 MAX
.270 MAX
.018
.300
+.004
4
5
.300
+.004
.200 MAX
.070
GLASS INSULATORS (4)
Glass Insulators (4)
“M” Package
“H” Package
“M” Package
with Gull Wing
“H” Package
with Gull Wing
ELECTRONICS
10 Commerce Dr • New Rochelle NY 10801
International Sales: +1.914-712-2200
•
USA Sales: +1.800.331.1236
•
Fax: 914.712.2290
•
www.mfelectronics.com
•
email:sales@mfelectronics.com
1 of 3
VOLTAGE CONTROLLED
CRYSTAL OSCILLATORS
HCMOS/TTL 5V
Thru-Hole/Gull Wing
Industrial: -40º to +85ºC
1 KHz to 150 MHz
FULL SIZE D.I.L.
M package
M6001 thru M6007
M6021 thru M6023
HALF SIZE D.I.L.
H package
H6001 thru H6007
H6021 thru H6023
Center Frequency is Between Two Voltages
with ±50 ppm stability
Control
Voltage
(Volts)
0.3 to 10.0
0.3 to 4.0
0.3 to 10.0
0.3 to 4.0
1.0 to 4.0
0 to 5.0
0.5 to 4.5
Frequency
Deviation
(ppm)
± 175 min
± 75 min
± 175 to 300
± 125 min
± 75 to 300
± 150 min
± 125 to 250
Guaranteed Control
Center
Capture
Voltage Frequency
Range
at Center Stability
(ppm)
Frequency
(ppm)
± 175
± 75
± 175
± 125
± 75
± 150
± 125
2.5 to 5.0
1.3 to 2.3
2.5 to 5.0
1.3 to 2.3
1.8 to 3.0
—
1.8 to 3.0
MODEL
6001
6002
6003
6004
6005
6006
6007
± 40, typ
± 50, max
Center Frequency is at 2.5V with ±50 ppm stability
Control
Voltage
(Volts)
0.5 to 4.5
0.5 to 4.5
0.5 to 4.5
Frequency
Deviation
(ppm)
± 75 to 150
± 100 to 200
± 150 to 300
Guaranteed Control
Center
Capture
Voltage Frequency
Range
at Center Stability
(ppm)
Frequency
(ppm)
± 75
± 100
± 150
2.5
2.5
2.5
± 30, typ
± 50, max
MODEL
6021
6022
6023
ELECTRICAL SPECIFICATIONS
Frequency Stability
Includes calibration at 25°C, operating temperature,
change of input voltage, change of load, shock and
vibration.
Center Frequency Range
V
C
= 2.5V
1 KHz to 150 MHz
MIN
TYP
MAX UNITS
Input Voltage
4.5
5.0
5.5
volts
Input Current
30
45
mA
Output Levels (HCMOS)
“0” Level, sinking 16 mA.
0.4
volts
“1” Level, sourcing 10 mA.
V
DD
-.4
volts
Rise and Fall Times, HCMOS
2.5
4
ns
From 0.4 to (V
DD
-.4) V
(Above 35 MHz)
2
ns
Symmetry
At V
DD
/ 2
45/55 percent
Aging
First year
3
ppm
After first year
1
ppm/yr
Input Impedance,
Pin 5., Control Voltage
15
1000
Kohms
Control Voltage Bandwidth
15
150
KHz
ENVIRONMENTAL SPECIFICATIONS
Temperature
Operating
-40º to +85°C
Storage
-55º to +125°C
Temperature Cycle
– Not to exceed ±5 ppm change when exposed to 2
hours maximum at each temperature from 0 to 120°C, with 25°C reference
Shock
– 1000 Gs, 0.35 ms, 1/2 sine wave, 3 shocks in each plane
Vibration
– 10-2000 Hz of .06" d.a. or 20 Gs, whichever is less
Humidity
– Resistant to 85° R.H. at 85°C
MECHANICAL SPECIFICATIONS
Gross Leak
– Each unit checked in 125°C fluorocarbon
Fine Leak
– Mass spectrometer leak rate less than 2 X 10-8 atm,
cc/sec of helium
Pins
– Kovar, nickel plated with 60/40 solder coat
Bend Test
– Will withstand two bends of 90° from reference
Header
– Steel, with nickel plated
Case
– Stainless steel, type 304
Marking
– Permanent black epoxy ink or laser marked
Resistance to Solvents
– MIL STD 202, Method 215
DESCRIPTIONS
M6001, H6001
M6002, H6002
M6003, H6003
M6004, H6004
M6005, H6005
±175 ppm, min. deviation when using
0.3 to 10V control-voltage
±75 ppm, min. deviation when using
0.3 to 4.0V control-voltage
±175 ppm to ±300 ppm deviation when using
0.3 to 10V control-voltage
±125 ppm deviation when using
0.3 to 4.0V control-voltage
±75 ppm to ±300 ppm deviation when using
1.0 to 4.0 control-voltage, for use where the
control voltage is 1 volt off both rails
±150 ppm, min. deviation when using
0 to 5.0 control-voltage
±125 ppm to ±250 ppm deviation when using
0.5 to 4.5 control-voltage
±75 ppm capture when using 0.5 to 4.5V
control-voltage and 2.5V center with 50 ppm stability
±100 ppm capture when using 0.5 to 4.5V
control-voltage and 2.5V center with 50 ppm stability
±150 ppm capture when using 0.5 to 4.5V
control-voltage and 2.5V center with 50 ppm stability
M6006, H6006
M6007, H6007
M6021, H6021
M6022, H6022
M6023, H6023
FREQUENCY STABILITY
Frequency stability vs. Temperature is typically better than ±40 ppm
for -40 to +85°C. Since the deviation of each oscillator is tested
and guaranteed over the whole operating temperature range, it is
not necessary to make additional capture allowances. All oscillators
will capture frequencies with the full minimum values of the deviation
under all conditions.
ELECTRONICS
10 Commerce Dr • New Rochelle NY 10801
International Sales: +1.914-712-2200
•
USA Sales: +1.800.331.1236
•
Fax: 914.712.2290
•
www.mfelectronics.com
•
email:sales@mfelectronics.com
2 of 3
VOLTAGE CONTROLLED
CRYSTAL OSCILLATORS
HCMOS/TTl 5V
Thru-Hole/Gull Wing
Industrial: -40º to +85ºC
1 KHz to 150 MHz
FULL SIZE D.I.L.
M package
M6001 thru M6007
M6021 thru M6023
HALF SIZE D.I.L.
H package
H6001 thru H6007
H6021 thru H6023
PIN 1.
CONTROL VOLTAGE
V
DD
+5V
Power
Supply
GND
Half Size connections shown in ( )
To adapt Fet probe to receptacle
use Tektronix Part #103-0164-00
To connect output to scope use
use Tektronix Part #131-0258-00 (receptacle)
MA
1
(1)
14
(8)
FET PROBE
350 MHz
SCOPE
LOAD
Y-OUTPUT
7
(4)
8
(5)
COUNTER
ALL OSCILLATORS HAVE INTERNAL BYPASS CAPACITORS
TEST CIRCUIT
Fig. 1 M6022-16.384M,
with 50 pf load
M6022 -16.384M, TYPICAL
200
150
250
200
150
4.5 Volts
100
50
0
0
-50
-50
-100
-150
-200
-250
0.0 0.5
1.0 1.5
2.0 2.5
3.0 3.5
4.0 4.5
5.0
Temp -40°C
Temp 0°C
Temp 25°C
Temp 85°C
-100
0.5 Volts
-150
-200
0 Volts
-250
-40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100
0
-40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100
10
20
30
40
2.5 Volts
50
60
5.0 Volts
80
70
V
DD
= 4.5V
V
DD
= 5.0V
V
DD
= 5.5V
Frequency Deviation, ppm
100
50
Control Voltage, Vc
Temperature,
°C
Temperature,
°C
Fig. 2 Frequency vs. Control Voltage
Fig. 3 Frequency vs. Temperature
Fig. 4 Frequency vs. Temperature @ 2.5V
Control Voltage
HOW TO ORDER
For Part Number, put package type before model number,
and add frequency in MHz, for example:
M 6 0 0 1-1 2 . 3 5 2 M
“M” is full size DIL
“H” is half size DIL
“6001”
is model
type
“12.352 M”
frequency
in MHz
Leave blank
for straight leads
Add “G” for
gullwing
SS#
M6001
Rev.
A
ELECTRONICS
10 Commerce Dr • New Rochelle NY 10801
Unless customer-specific terms and conditions
are signed by an officer of MF Electronics, the
sale of this and all MF Electronics products are
subject to terms and conditions set forth at
www.mfelectronics.com/terms
International Sales: +1.914-712-2200
•
USA Sales: +1.800.331.1236
•
Fax: 914.712.2290
•
www.mfelectronics.com
•
email:sales@mfelectronics.com
3 of 3
TI Technology Forum
京公网安备 11010802033920号
EEWORLD
