The AMS1082 series of adjustable and fixed voltage regulators are designed to provide 10A output current and to operate
down to 1V input-to-output differential. The dropout voltage of the device is guaranteed maximum 1.5V at maximum output
current, decreasing at lower load currents.
On-chip trimming adjusts the reference voltage to 1%. Current limit is also trimmed, minimizing the stress under overload
conditions on both the regulator and power source circuitry.
The AMS1082 devices are pin compatible with older three-terminal regulators and are offered in 3 lead TO-220 package and 3
lead TO-263 (Plastic DD).
ORDERING INFORMATION:
PACKAGE TYPE
3 LEAD TO-220
AMS1082CT
AMS1082CT-1.5
AMS1082CT-2.5
AMS1082CT-2.85
AMS1082CT-3.0
AMS1082CT-3.3
AMS1082CT-3.5
AMS1082CT-5.0
3 LEAD TO-263
AMS1082CM
AMS1082CM-1.5
AMS1082CM-2.5
AMS1082CM-2.85
AMS1082CM-3.0
AMS1082CM-3.3
AMS1082CM-3.5
AMS1082CM-5.0
OPERATING JUNCTION
TEMPERATURE RANGE
0 to 125° C
0 to 125° C
0 to 125° C
0 to 125° C
0 to 125° C
0 to 125° C
0 to 125° C
0 to 125° C
FRONT VIEW
TAB IS
OUTPUT
3
2
1
PIN CONNECTIONS
FIXED VERSION
1- Ground
2- V
OUT
3- V
IN
ADJUSTABLE VERSION
1- Adjust
2- V
OUT
3- V
IN
TAB IS
OUTPUT
FRONT VIEW
3
2
1
Advanced Monolithic Systems, Inc.
www.advanced-monolithic.com
Phone (925) 443-0722
Fax (925) 443-0723
AMS1082
ABSOLUTE MAXIMUM RATINGS
(Note 1)
Power Dissipation
Input Voltage
Operating Junction Temperature
Control Section
Power Transistor
Storage temperature
Internally limited
15V
0°C to 125°C
0°C to 150°C
- 65°C to +150°C
Soldering information
Lead Temperature (25 sec)
Thermal Resistance
TO-220 package
TO-263 package
265°C
ϕ
JA
= 50°C/W
ϕ
JA
= 30°C/W *
* With package soldering to 0.5in
2
copper area over backside
ground plane or internal power plane
ϕ
JA
can vary from
20°C/W to
>40°C/W
depending on mounting technique.
ELECTRICAL CHARACTERISTICS
Electrical Characteristics at I
OUT
= 0 mA, and T
J
= +25°C unless otherwise specified.
Parameter
Reference Voltage
(Note 2)
Output Voltage
(Note 2)
Device
AMS1082
AMS1082-1.5
AMS1082-2.5
AMS1082-2.85
AMS1082-3.0
AMS1082-3.3
AMS1082-3.5
AMS1082-5.0
Conditions
I
OUT
= 10 mA
10mA
≤
I
OUT
≤
10A, 1.5V≤ (V
IN
- V
OUT
)
≤
12V
0
≤
I
OUT
≤
10A , 3V≤ V
IN
≤
12V
0
≤
I
OUT
≤
10A , 4V≤ V
IN
≤
12V
0
≤
I
OUT
≤
10A , 4.35V≤ V
IN
≤
12V
0
≤
I
OUT
≤
10A , 4.5V
≤
V
IN
≤
12V
0
≤
I
OUT
≤
10A , 4.75V
≤
V
IN
≤
12V
0
≤
I
OUT
≤
10A, 5V
≤
V
IN
≤
12V
0
≤
I
OUT
≤
10A , 6.5V
≤
V
IN
≤
12V
I
LOAD
= 10 mA , 1.5V≤ (V
IN
- V
OUT
)
≤
12V
(V
IN
- V
OUT
) =3V, 10mA
≤
I
OUT
≤
10A
V
IN
= 5V, 0
≤
I
OUT
≤
10A
V
IN
= 5V, 0
≤
I
OUT
≤
10A
V
IN
= 5V, 0
≤
I
OUT
≤
10A
V
IN
= 5V, 0
≤
I
OUT
≤
10A
V
IN
= 5V, 0
≤
I
OUT
≤
10A
V
IN
= 5.25V, 0
≤
I
OUT
≤
10A
V
IN
= 8V, 0
≤
I
OUT
≤
10A
∆V
OUT
,
∆V
REF
= 1%, I
OUT
= 8 A (Note 4)
Min
1.238
1.225
1.485
1.470
2.475
2.450
2.820
2.790
2.970
2.940
3.267
3.235
3.465
3.430
4.950
4.900
Typ
1.250
1.250
1.500
1.500
2.500
2.500
2.850
2.850
3.000
3.000
3.300
3.300
3.500
3.500
5.000
5.000
0.3
0.6
0.1
0.2
3
6
3
6
3
6
3
6
3
7
3
6
5
10
1.3
Max
1.262
1.270
1.515
1.530
2.525
2.550
2.880
2.910
3.030
3.360
3.333
3.365
3.535
3.570
5.050
5.100
6
10
0.3
0.4
12
20
12
20
12
20
12
20
15
25
15
25
20
35
1.5
Units
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
mV
mV
%
%
mV
mV
mV
mV
mV
mV
mV
mV
mV
mV
mV
mV
mV
mV
V
Line Regulation
Load Regulation
(Notes 2, 3)
AMS1082/-1.5/-2.5/-
2.85/ -3.0/-3.3/-3.5/-5.0
AMS1082
AMS1082-1.5
AMS1082-2.5
AMS1082-2.85
AMS1082-3.0
AMS1082-3.3
AMS1082-3.5
AMS1082-5.0
Dropout Voltage
(V
IN
-
V
OUT
)
AMS1082/-1.5/-2.5/-
2.85/ -3.0/-3.3/-3.5/-5.0
Advanced Monolithic Systems, Inc.
www.advanced-monolithic.com
Phone (925) 443-0722
Fax (925) 443-0723
AMS1082
ELECTRICAL CHARACTERISTICS
Electrical Characteristics at I
OUT
= 0 mA, and T
J
= +25°C unless otherwise specified.
Parameter
Current Limit
Minimum Load
Current
Quiescent Current
Ripple Rejection
Device
AMS1082/-1.5/-2.5/-
2.85/ -3.0/-3.3/-3.5/-5.0
AMS1082
AMS1082/-1.5/-2.5/-
2.85/ -3.0/-3.3/-3.5/-5.0
AMS1082
AMS1082-1.5
AMS1082-2.5
AMS1082-2.85
AMS1082-3.0
AMS1082-3.3
AMS1082-3.5
AMS1082-5.0
Conditions
(V
IN
- V
OUT
) = 5V
(V
IN
- V
OUT
) = 12V (Note 5)
V
IN
≤
12V
f =120Hz , C
OUT
= 25µF Tantalum, I
OUT
= 10A,
(V
IN
-V
OUT
) = 3V, C
ADJ
=25µF
f =120Hz , C
OUT
= 25µF Tantalum, I
OUT
= 10A,
V
IN
= 4.5V
f =120Hz , C
OUT
= 25µF Tantalum, I
OUT
= 10A,
V
IN
= 5.5V
f =120Hz , C
OUT
= 25µF Tantalum, I
OUT
= 10A,
V
IN
= 6V
f =120Hz , C
OUT
= 25µF Tantalum, I
OUT
= 10A
V
IN
= 6V
f =120Hz , C
OUT
= 25µF Tantalum, I
OUT
= 10A
V
IN
= 6.3V
f =120Hz , C
OUT
= 25µF Tantalum, I
OUT
= 10A
V
IN
= 6.5V
f =120Hz , C
OUT
= 25µF Tantalum, I
OUT
= 10A
V
IN
= 8V
T
A
= 25°C, 30ms pulse
10mA
≤
I
OUT
≤
10A , 1.5V≤ (V
IN
- V
OUT
)
≤
12V
10mA
≤
I
OUT
≤
10A , 1.5V≤ (V
IN
- V
OUT
)
≤
12V
Min
10.1
Typ
11.0
5
5
Max
12.0
10
10
Units
A
mA
mA
dB
dB
dB
dB
dB
dB
dB
dB
60
60
60
60
60
60
60
60
75
72
72
72
72
72
72
68
0.008
55
120
0.2
0.5
5
0.04
Thermal Regulation
Adjust Pin Current
Adjust Pin Current
Change
Temperature Stability
Long Term Stability
RMS Output Noise
(% of V
OUT
)
Thermal Resistance
Junction-to-Case
AMS1082
AMS1082
AMS1082
%W
µA
µA
µA
%
T
A
=125°C, 1000Hrs
T
A
= 25°C , 10Hz
≤
f
≤
10kHz
M Package: Control Circuitry/ Power Transistor
T Package: Control Circuitry/ Power Transistor
0.3
0.003
1
%
%
1.5/4.0
1.5/4.0
°C/W
°C/W
Parameters identified with
boldface type
apply over the full operating temperature range.
Note 1:
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. For guaranteed specifications and test conditions, see the
Electrical Characteristics
.
The guaranteed specifications apply only for the test conditions listed.
Note 2:
Line and Load regulation are guaranteed up to the maximum power dissipation of 15W. Power dissipation is determined by the input/output
differential and the output current. Guaranteed maximum power dissipation will not be available over the full input/output range.
Note 3:
See thermal regulation specifications for changes in output voltage due to heating effects. Line and load regulation are measured at a constant junction
temperature by low duty cycle pulse testing. Load regulation is measured at the output lead ~1/8” from the package.
Note 4:
Dropout voltage is specified over the full output current range of the device.
Note 5:
Minimum load current is defined as the minimum output current required to maintain regulation. When (V
IN
- V
OUT
) = 12V the device is guaranteed
to regulate if the output current is greater than 10mA.
Advanced Monolithic Systems, Inc.
www.advanced-monolithic.com
Phone (925) 443-0722
Fax (925) 443-0723
AMS1082
APPLICATION HINTS
The AMS1082 series of adjustable and fixed regulators are easy to
use and have all the protection features expected in high
performance voltage regulators: short circuit protection and
thermal shut-down.
Pin compatible with older three terminal adjustable regulators,
these devices offer the advantage of a lower dropout voltage, more
precise reference tolerance and improved reference stability with
temperature.
Stability
The circuit design used in the AMS1082 series requires the use of
an output capacitor as part of the device frequency compensation.
The addition of
150
µF
aluminum electrolytic or a 22µF solid
tantalum on the output will ensure stability for all operating
conditions.
When the adjustment terminal is bypassed with a capacitor to
improve the ripple rejection, the requirement for an output
capacitor increases. The value of 22µF tantalum or
150
µF
aluminum covers all cases of bypassing the adjustment terminal.
Without bypassing the adjustment terminal smaller capacitors can
be used with equally good results.
To ensure good transient response with heavy load current
changes capacitor values on the order of 100µF are used in the
output of many regulators. To further improve stability and
transient response of these devices larger values of output
capacitor can be used.
Protection Diodes
Unlike older regulators, the AMS1082 family does not need any
protection diodes between the adjustment pin and the output and
from the output to the input to prevent over-stressing the die.
Internal resistors are limiting the internal current paths on the
AMS1082 adjustment pin, therefore even with capacitors on the
adjustment pin no protection diode is needed to ensure device
safety under short-circuit conditions.
Diodes between the input and output are not usually needed.
Microsecond surge currents of 50A to 100A can be handled by the
internal diode between the input and output pins of the device. In
normal operations it is difficult to get those values of surge
currents even with the use of large output capacitances. If high
value output capacitors are used, such as 1000µF to 5000µF and
the input pin is instantaneously shorted to ground, damage can
occur. A diode from output to input is recommended, when a
crowbar circuit at the input of the AMS1082 is used. Normal
power supply cycling or even plugging and unplugging in the
system will not generate current large enough to do any damage.
The adjustment pin can be driven on a transient basis
±25V,
with
respect to the output without any device degradation. As with any
IC regulator, none the protection circuitry will be functional and
the internal transistors will break down if the maximum input to
output voltage differential is exceeded.
D1
V
IN
AMS1082
IN
OUT
ADJ
C
ADJ
10µF
V
OUT
R
1
R
2
+
C
OUT
150µF
Overload Recovery
When the power is first turned on, as the input voltage rises, the
output follows the input, permitting the regulator to start up into
heavy loads. During the start-up, as the input voltage is rising, the
input-to-output voltage differential remains small, allowing the
regulator to supply large output currents. A problem can occur
with a heavy output load when the input voltage is high and the
output voltage is low, when the removal of an output short will
not permit the output voltage to recover. The load line for such a
load may intersect two points on the output current curve. In this
case, there are two stable output operating points for the regulator.
With this double intersection, the power supply may need to be
cycled down to zero and brought up again to make the output
recover.
Ripple Rejection
The ripple rejection values are measured with the adjustment pin
bypassed. The impedance of the adjust pin capacitor at the ripple
frequency should be less than the value of R1 (normally 100Ω
to120Ω) for a proper bypassing and ripple rejection approaching
the values shown. The size of the required adjust pin capacitor is a
function of the input ripple frequency. If R1=100Ω at 120Hz the
adjust pin capacitor should be 25µF. At 10kHz only 0.22µF is
needed.
The ripple rejection will be a function of output voltage, in
circuits without an adjust pin bypass capacitor. The output ripple
will increase directly as a ratio of the output voltage to the
reference voltage (V
OUT
/ V
REF
).
Output Voltage
The AMS1082 series develops a 1.25V reference voltage between
the output and the adjust terminal. Placing a resistor between these
two terminals causes a constant current to flow through R1 and
down through R2 to set the overall output voltage.
Advanced Monolithic Systems, Inc.
www.advanced-monolithic.com
Phone (925) 443-0722
Fax (925) 443-0723
AMS1082
APPLICATION HINTS
This current is normally the specified minimum load current of
10mA. Because I
ADJ
is very small and constant it represents a
small error and it can usually be ignored.
Connected as shown, R
P
is not multiplied by the divider ratio.
Using 16-gauge wire the parasitic line resistance is about 0.004Ω
per foot, translating to 4mV/ft at 1A load current. It is important
to keep the positive lead between regulator and load as short as
possible and use large wire or PC board traces.
Thermal Considerations
The AMS1082 series have internal power and thermal limiting
circuitry designed to protect the device under overload conditions.
However maximum junction temperature ratings should not be
exceeded under continuous normal load conditions. Careful
consideration must be given to all sources of thermal resistance
from junction to ambient, including: junction-to-case, case-to-heat
sink interface and heat sink resistance itself. To ensure safe
operating temperatures and reflect more accurately the device
temperature, new thermal resistance specifications have been
developed. Unlike older regulators with a single junction-to-case
thermal resistance specification, the data section for these new
regulators provides a separate thermal resistance and maximum
junction temperature for both the Control Section and the Power
Transistor. Calculations for both temperatures under certain
conditions of ambient temperature and heat sink resistance and to
ensure that both thermal limits are met.
Junction-to-case thermal resistance is specified from the IC
junction to the bottom of the case directly below the die. This is
the lowest resistance path for the heat flow. In order to ensure the
best possible thermal flow from this area of the package to the
heat sink proper mounting is required. Thermal compound at the
case-to-heat sink interface is recommended. A thermally
conductive spacer can be used, if the case of the device must be
electrically isolated, but its added contribution to thermal
resistance has to be considered.
V
IN
AMS1082
IN
OUT
ADJ
I
ADJ
50µA
V
OUT
V
REF
R1
R2
V
OUT
= V
REF
(1+
R2/R1)+I
ADJ
R2
Figure 1. Basic Adjustable Regulator
Load Regulation
True remote load sensing it is not possible to provide, because the
AMS1082 is a three terminal device. The resistance of the wire
connecting the regulator to the load will limit the load regulation.
The data sheet specification for load regulation is measured at the
bottom of the package. Negative side sensing is a true Kelvin
connection, with the bottom of the output divider returned to the
negative side of the load.
The best load regulation is obtained when the top of the resistor
divider R1 is connected directly to the case not to the load. If R1
were connected to the load, the effective resistance between the
TMS320C6678 is an 8-core DSP processor based on KeyStone architecture. The frequency of each CorePac core is up to 1.25 GHz, providing powerful fixed-point and floating-point computing capabilities. A...
First of all, I would like to thank EEWORLD and administrator Orange Kai for giving me the chance to get TI's millimeter wave radar AWR1443EVM board for evaluation;
In actual use, the industry I work ...
MIPI D-PHY BasicsThe DPHY bus includes the DSI and CSI buses for display and camera. D-PHY is different from many existing mobile interfaces. It can switch between differential mode (high speed) and s...
1. warning: creating .stack section with default size of 400 (hex) words.This is because there is no set value for -stack in Project---Build Option---Linker.
2. warning: creating .sysmem section with ...
[i=s]This post was last edited by damiaa on 2019-5-17 11:00[/i] [STM32WB55 Evaluation] +thread trial 1 [font="] [/font][font="][STM32WB55 Evaluation] +After the wireless firmware update is completed. ...
[i=s]This post was last edited by bqgup on 2021-7-26 23:36[/i]Sound source localization system
The list of required materials is as follows:
MCU Development System
DSP Development System
Embedded deve...
The principle of the venturi flowmeter is that when the wind blows through an obstacle, the air pressure near the port above the leeward side of the obstacle is relatively low, which produces an adso...[Details]
and the host Bluetooth address) After receiving the scan request, the slave replies SCAN_RSP PDU on the same channel. After receiving the scan reply information, the host sends CONNECT_REQ PDU info...[Details]
SABIC attended the 2023 Boao Forum for Asia: Join hands to create a sustainable future Today, Saudi Basic Industries Corporation (SABIC), a world-renowned diversified chemical company, issued an i...[Details]
1. Advantages of sewage flow meter: (1) The measuring channel of the sewage flow meter is a smooth straight tube without flow-blocking detection parts. Because it is not easy to be blocked, it is sui...[Details]
A Honor phone with model number TEL-AN00 previously appeared on the website of the Ministry of Industry and Information Technology. It supports 5G. It is reported that this product is likely to be th...[Details]
Many people worry about the battery life before buying an electric car. We often receive such inquiries in the background, such as how durable is the battery? Is it expensive to replace the battery? ...[Details]
On the afternoon of December 13, Deputy Director Huang Duanwei of Nanchang Science and Technology Bureau, Director Sheng Huilong of High-tech Department, and Deputy Director Wang Rongxian visited H...[Details]
This paper introduces the definition, classification and principle of electronic transformers in detail, analyzes the types, principles and main problems of active and passive electronic tra...[Details]
1. What is Power Factor Correction (PFC)?
Power factor refers to the relationship between effective power and total power consumption (apparent power), that is, the ratio of effective power ...[Details]
Let me share with you how to use the positive motion auxiliary debugging tool ZDevelop to debug the EtherCAT motion control card ECI2820. This article takes the single-axis routine as an example to...[Details]
The American "Tom Hardware" website reported that AMD, Nvidia, Intel and other companies sell large quantities of advanced chips to China, and the US suppression will inevitably hurt these American c...[Details]
According to The Paper, the 2019 International Chip Conference (Chips 2019) was held in Beijing recently, and Ni Guangnan, an academician of the Chinese Academy of Engineering, looked forward to the ...[Details]
0 Introduction
In recent years, with the rapid economic development and the gradual popularization of automobiles, urban traffic problems have attracted more and more attention, and the importa...[Details]
Individually, each battery cell is small and may seem insignificant. However, when hundreds of these cells are connected in series and parallel, they form the backbone of an electric vehicle's powe...[Details]
DSP and ARM Processors
京公网安备 11010802033920号
EEWORLD
