M35
www.vishay.com
Vishay
Wet Tantalum Capacitors Surface Mount, Molded Case
FEATURES
• Molded surface mountable design
• Terminations: standard tin/lead (SnPb),
100 % tin (RoHS compliant) available
• Industry standard ratings
• Model M35 wet tantalum electrolytic chip
capacitors incorporate the advantages of all the
varieties of electrolytic capacitors and eliminate most of
the disadvantages. These units have a 3 V reverse voltage
capability at + 85 °C and a higher ripple current capability
than any other electrolytic type with similar combinations
of capacitance and case size.
• Compliant to RoHS Directive 2002/95/EC
Note
*
Pb containing terminations are not RoHS compliant, exemptions
may apply
PERFORMANCE CHARACTERISTICS
Operating Temperature:
- 55 °C to + 85 °C
(to + 125 °C with voltage derating)
Capacitance Tolerance:
At 120 Hz, + 25 °C. ± 20 %
standard. ± 10 %, ± 5 % available as special.
DC Leakage Current (DCL Max.):
At + 25 °C and above:
Leakage current shall not exceed the values listed in the
Standard Ratings Tables.
Life Test:
Capacitors are capable of withstanding a 2000 h
life test at a temperature of + 85 °C or + 125 °C at the
applicable rated DC working voltage.
Following life test:
1. DCL, measured at + 85 °C rated voltage, shall not be in
excess of the original requirement.
2. The equivalent series resistance shall not exceed 150 %
of the initial requirement.
3. Change in capacitance shall not exceed 10 % from the
initial measurement.
ORDERING INFORMATION
M35
MODEL
C
CASE
CODE
See
Ratings
and Case
Codes
table
826
CAPACITANCE
This is
expressed in
picofarads.
The first two
digits are the
significant
figures. The
third is the
number of zeros
to follow.
M
CAPACITANCE
TOLERANCE
K = ± 10 %
M = ± 20 %
125
DC VOLTAGE RATING
AT + 85 °C
This is expressed in
volts. To complete the
three-digit block,
zeros precede the
voltage rating.
A decimal point is
indicated by an “R”
(6R3 = 6.3 V)
B
TERMINATION
AND PACKAGING
A = 100 % tin
(RoHS compliant),
bulk
B = Std, tin/lead,
bulk
Z
RELIABILITY
LEVEL
Z = Non-ER
S
TEMP
S = Std
L
ESR
S = Std.
L = Low
Note
• Packaging: The use of formed plastic tubes for packing bulk components is standard
DIMENSIONS
in inches [millimeters]
T
W
P
H
T
H
L
W
CASE CODE
C
L (MAX.)
0.835
[21.2]
W
0.315 ± 0.012
[8 ± 0.3]
H
0.295 ± 0.012
[7.5 ± 0.3]
P (MIN.)
0.118
[3.0]
T
W
0.236 ± 0.012
[6.0 ± 0.3]
T
H
(MIN.)
0.075
[1.9]
Revision: 07-Nov-11
Document Number: 40095
1
For technical questions, contact:
tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
M35
www.vishay.com
Vishay
RECOMMENDED REFLOW PROFILES
T
p
°C
t
p
T
L
°C
TEMPERATURE (°C)
T
s
MAX. °C
(t
L
)
T
s
MIN. °C
PREHEAT (t
s
)
25 °C
TIME (s)
ALL CASE CODES
T
p
T
p
Lead (Pb)-free Sn/Pb
260 °C
t
p
T
L
T
s
MIN.
T
s
MAX.
T
s
MAX.
t
s
T
L
T
s
MIN.
Lead (Pb)-free Sn/Pb Lead (Pb)-free Sn/Pb Lead (Pb)-free Sn/Pb Lead (Pb)-free
217 °C
183 °C
150 °C
100 °C
200 °C
150 °C
60 to 150
t
s
Sn/Pb
t
L
240 °C 10
60 to 90 60
MOUNTING
Due to the size and weight of these capacitors, we recommend that a supplemental mounting restraint to be used in printed
circuit board attachment in addition to the reflowed solder.
One recommendation is to use an adhesive such as defined in the J-STD-001DS.
This is the Space Application Electronic Hardware Addendum to J-STD-001 (Requirements for Solder Electrical and Electronic
Assemblies).
STANDARD RATINGS
CAPACITANCE
(μF)
CASE
CODE
PART NUMBER
MAX.
RIPPLE
MAX. ESR MAX. ESR
40 kHz
AT + 25 °C AT - 55 °C
+ 85 °C
RMS
- 55 °C + 85 °C + 125 °C
+ 25 °C
+ 125 °C
(mA)
MAX. DCL (μA) AT
6 V
DC
AT + 85 °C; 4 V
DC
AT + 125 °C
30
68
220
25
56
180
20
47
120
150
C
C
C
C
C
C
C
C
C
C
M35C306(1)006(2)ZS(3)
M35C686(1)006(2)ZS(3)
M35C227(1)006(2)ZS(3)
M35C256(1)008(2)ZS(3)
M35C566(1)008(2)ZS(3)
M35C187(1)008(2)ZS(3)
M35C206(1)010(2)ZS(3)
M35C476(1)010(2)ZS(3)
M35C127(1)010(2)ZS(3)
M35C157(1)010(2)ZS(3)
4.0
3.2
3.0
4.0
3.3
3.0
4.0
3.7
3.2
3.0
100
60
36
100
59
45
120
90
54
54
1.0
1.0
2.0
1.0
1.0
2.0
1.0
1.0
2.0
2.0
2.0
2.0
9.0
2.0
2.0
9.0
2.0
2.0
6.0
9.0
- 40
- 40
- 64
- 40
- 40
- 60
- 32
- 36
- 40
- 55
+ 10.5
+ 14
+ 13
+ 10.5
+ 14
+ 13
+ 10.5
+ 14
+ 14
+ 13
+ 12
+ 16
+ 16
+ 12
+ 16
+ 16
+ 12
+ 16
+ 16
+ 16
820
960
1000
820
900
1000
820
855
900
900
MAX. CAPACITANCE
CHANGE (%) AT
8 V
DC
AT + 85 °C; 5 V
DC
AT + 125 °C
10 V
DC
AT + 85 °C; 7 V
DC
AT + 125 °C
Note
• Part number definitions:
(1) Capacitance tolerance: K, M
(2) Termination/packaging: (see Ordering Information)
Reliability level: Z = Non-ER
Temperature: S = STD
(3) ESR: S = STD, L = Low (1/2 standard ESR value)
Revision: 07-Nov-11
Document Number: 40095
2
For technical questions, contact:
tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
M35
www.vishay.com
Vishay
MAX.
RIPPLE
MAX. ESR MAX. ESR
40 kHz
AT + 25 °C AT - 55 °C
+ 85 °C
RMS
+ 25 °C + 125 °C - 55 °C + 85 °C + 125 °C
(mA)
MAX. DCL (μA) AT
15 V
DC
AT + 85 °C; 10 V
DC
AT + 125 °C
4.4
4.0
3.9
3.9
5.3
4.2
4.3
4.3
6.6
6.2
5.2
5.2
6.2
4.1
8.0
6.4
5.0
9.3
6.6
5.0
9.5
6.8
5.1
10.6
8.5
5.9
15.6
10.0
11.7
155
90
72
72
220
140
90
90
275
175
100
100
175
61
400
250
135
550
275
144
650
300
157
950
500
200
1250
600
300
1.0
1.0
2.0
2.0
1.0
1.0
2.0
2.0
1.0
1.0
2.0
2.0
0.75
2.0
1.0
1.0
2.0
1.0
1.0
3.0
1.0
1.0
3.0
1.0
1.0
3.0
1.0
1.0
3.0
2.0
2.0
6.0
9.0
2.0
2.0
6.0
9.0
2.0
2.0
6.0
9.0
1.5
6.0
2.0
2.0
9.0
2.0
2.0
12
2.0
2.0
12
2.0
2.0
12
2.0
2.0
12
- 24
- 28
- 35
- 44
- 16
- 20
- 25
- 40
- 16
- 20
- 23
- 38
- 20
- 22
- 16
- 24
- 29
- 16
- 24
- 24
- 16
- 20
- 19
- 16
- 16
- 17
- 16
- 16
- 14
+ 10.5
+ 14
+ 12
+ 13
+8
+ 10.5
+ 12
+ 12
+8
+ 10.5
+ 12
+ 12
+ 10.5
+ 12
+5
+8
+ 10
+5
+8
+ 10
+5
+8
+ 10
+7
+7
+ 10
+7
+7
+ 10
+ 12
+ 16
+ 16
+ 16
+9
+ 12
+ 15
+ 15
+ 12
+ 12
+ 15
+ 15
+ 12
+ 14
+6
+9
+ 12
+6
+9
+ 12
+6
+9
+ 12
+8
+8
+ 12
+8
+8
+ 12
780
820
900
900
715
800
850
850
640
780
800
800
660
820
580
715
700
525
625
700
525
610
600
505
565
800
415
520
700
MAX. CAPACITANCE
CHANGE (%) AT
STANDARD RATINGS
CAPACITANCE
(μF)
CASE
CODE
PART NUMBER
15
33
82
100
10
22
56
68
8
15
47
56
15
39
5
10
33
4
8.2
27
3.5
6.8
22
2.5
4.7
10
1.7
3.6
6.8
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
M35C156(1)015(2)ZS(3)
M35C336(1)015(2)ZS(3)
M35C826(1)015(2)ZS(3)
M35C107(1)015(2)ZS(3)
M35C106(1)025(2)ZS(3)
M35C226(1)025(2)ZS(3)
M35C566(1)025(2)ZS(5)
M35C686(1)025(2)ZS(5)
M35C805(1)030(2)ZS(3)
M35C156(1)030(2)ZS(3)
M35C476(1)030(2)ZS(3)
M35C566(1)030(2)ZS(3)
M35C156(1)035(2)ZS(3)
M35C396(1)035(2)ZS(3)
M35C505(1)050(2)ZS(3)
M35C106(1)050(2)ZS(3)
M35C336(1)050(2)ZS(3)
M35C405(1)060(2)ZS(3)
M35C825(1)060(2)ZS(3)
M35C276(1)060(2)ZS(3)
M35C355(1)075(2)ZS(3)
M35C685(1)075(2)ZS(3)
M35C226(1)075(2)ZS(3)
M35C255(1)100(2)ZS(3)
M35C475(1)100(2)ZS(3)
M35C106(1)100(2)ZS(3)
M35C175(1)125(2)ZS(3)
M35C365(1)125(2)ZS(3)
M35C685(1)125(2)ZS(3)
25 V
DC
AT + 85 °C; 15 V
DC
AT + 125 °C
30 V
DC
AT + 85 °C; 20 V
DC
AT + 125 °C
35 V
DC
AT + 85 °C; 22 V
DC
AT + 125 °C
50 V
DC
AT + 85 °C; 30 V
DC
AT + 125 °C
60 V
DC
AT + 85 °C; 40 V
DC
AT + 125 °C
75 V
DC
AT + 85 °C; 50 V
DC
AT + 125 °C
100 V
DC
AT + 85 °C; 65 V
DC
AT + 125 °C
125 V
DC
AT + 85 °C; 85 V
DC
AT + 125 °C
Note
• Part number definitions:
(1) Capacitance tolerance: K, M
(2) Termination/packaging: (see Ordering Information)
Reliability level: Z = Non-ER
Temperature: S = STD
(3) ESR: S = STD, L = Low (1/2 standard ESR value)
Revision: 07-Nov-11
Document Number: 40095
3
For technical questions, contact:
tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
M35
www.vishay.com
PERFORMANCE CHARACTERISTICS OF M35 CAPACITORS
ELECTRICAL CHARACTERISTICS
ITEM
Operating temperature range
Capacitor tolerance
Capacitance change (maximum)
ESR
AC ripple current
DCL (maximum leakage current)
Impedance (maximum)
Reverse voltage
PERFORMANCE CHARACTERISTICS
- 55 °C to + 125 °C
± 20 %, ± 10 % at 120 Hz
Vishay
Limits per Standard Ratings table. Measured per requirements of MIL-PRF-39006.
Surge voltage
Life test
Reverse voltage shall be in accordance with MIL-PRF-39006/22.
Units are capable of withstanding 3 V in reverse at + 85 °C for 125 h.
Surge voltage shall be in accordance with MIL-PRF-39006.
The DC rated surge voltage is the maximum voltage to which the capacitors should be subjected
under any conditions. This includes transients and peak ripple at the highest line voltage. The
surge voltage is 115 % of rated DC working voltage.
The capacitors shall be capable of withstanding a 2000 h life test at 85 °C at rated voltage.
ENVIRONMENTAL CHARACTERISTICS
ITEM
Hermeticity
Moisture resistance
Altitude/barometric pressure
(reduced)
CONDITION
MIL-PRF-39006
MIL-PRF-39006
MIL-PRF-39006
COMMENTS
The internal component has been tested to be compliant to
hermeticity requirements of MIL-PRF-39006/22.
The internal component has been tested to be compliant to
moisture resistance requirements of MIL-PRF-39006/22.
The internal component has been tested to be compliant to
altitude or reduced barometric pressure requirements
MIL-PRF-39006/22 (150 000 feet).
the
the
the
of
MECHANICAL CHARACTERISTICS
ITEM
Thermal shock
Shock
Vibration (high frequency)
Vibration (random)
Resistance to solder heat
Solderability
Part markings
Weight (typical) in g
CONDITION
MIL-STD-202, Method 107, A
MIL-STD-202, Method 213
MIL-STD-202, Method 204
MIL-STD-202, Method 214
MIL-STD-202, Method 210
ANSI J-STD-002
MIL-STD-1285
3.5
COMMENTS
Per MIL-PRF-39006, 30 cycles
Per MIL-PRF-39006, 500 g
Per MIL-PRF-39006, 80 g
Per MIL-PRF-39006, 53.79 g
The capacitor must withstand solder dipping of the terminals at
260 °C for 10 s. The capacitor must not be visibly damaged and the
electrical characteristics must not be affected.
The terminations must be solderable per the requirements of
MIL-PRF-55365 para. 4.10
The part marking shall include Vishay name, trademark,
capacitance, voltage, date code and lot symbol.
PAD DIMENSIONS
in millimeters
A
C
B
C
CASE CODE
C
A (MIN.)
22.7
B (NOM.)
14.7
D
C (NOM.)
4.0
D (NOM.)
6.4
STANDARD PACKAGING QUANTITY
SERIES
M35
Revision: 07-Nov-11
CASE CODE
C
BULK/TUBE
10 pcs
Document Number: 40095
4
For technical questions, contact:
tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree
to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and
damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay
or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to
obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Revision: 12-Mar-12
1
Document Number: 91000
京公网安备 11010802033920号
EEWORLD
