DATASHEET
PLL CLOCK MULTIPLIER
Description
The IDT5V80013 is the most cost effective way to generate
a high-quality, high-frequency clock output. Using
Phase-Locked Loop (PLL) techniques, the device employs
IDT’s propietary MEMs oscillator technology to produce
common output frequencies for consumer, computing, and
embedded applications.
IDT5V80013
Features
•
Packaged in a small form factor 16-pin QFN
•
Eliminates the need for an external crystal or input clock
•
•
•
•
•
•
•
source
Max. +50ppm error on CLK output
Typical ±75 ps short term cycle-cycle jitter
Output voltage of 3.3V
Operating voltage of 1.8V
Supports industrial temperature range
Supports output frequency on CLK up to 220MHz
Advanced, low-power CMOS process
Block Diagram
VDD
VDDO
MEMs
OScillator
PLL Clock
Synthesis
CLK
GND
IDT®
PLL CLOCK MULTIPLIER
1
IDT5V80013
REV J 022312
IDT5V80013
PLL CLOCK MULTIPLIER
CLOCK MULTIPLIER
Pin Assignment
CAP-IN
GND
VDD
VDD
CLK Output Frequency/Part Number Table
Frequency
11.2896 MHz
12 MHz
12.288 MHz
VDD
NC
GND
Orderable Part Number
5V80013-112NLGI
5V80013-012NLGI
5V80013-122NLGI
5V80013-143NLGI
5V80013-192NLGI
5V80013-020NLGI
5V80013-225NLGI
5V80013-024NLGI
5V80013-245NLGI
5V80013-025NLGI
5V80013-026NLGI
5V80013-027NLGI
5V80013-333NLGI
5V80013-338NLGI
5V80013-388NLGI
5V80013-048NLGI
5V80013-050NLGI
5V80013-614NLGI
5V80013-666NLGI
5V80013-742NLGI
5V80013-741NLGI
5V80013-125NLGI
VDD
GND
GND
OE
1
13
14.31818 MHz
19.2 MHz
20 MHz
22.5792 MHz
24 MHz
24.576 MHz
25 MHz
26 MHz
27 MHz
33.3333 MHz
33.8688 MHz
38.864 MHz
48 MHz
50 MHz
61.44MHz
66.6666 MHz
74.25 MHz
74.175824 MHz
125 MHz
5
9
CLK
16-pin QFN
VDDO
GND
VDD
VDD
Note: Contact IDT for any other frequencies.
IDT®
PLL CLOCK MULTIPLIER
2
IDT5V80013
REV J 022312
IDT5V80013
PLL CLOCK MULTIPLIER
CLOCK MULTIPLIER
Pin Descriptions
Pin
Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Pin
Name
VDD
GND
GND
OE
VDDO
VDD
VDD
GND
CLK
GND
NC
VDD
VDD
CAP-IN
GND
VDD
Pin
Type
Power
Connect to +1.8V.
Pin Description
Ground Connect this pin to ground.
Ground Connect this pin to ground.
Input
Power
Power
Power
Output
–
Power
Power
–
Power
Output enable pin for CLK output.
Connect to +3.3V.
Connect to +1.8V.
Connect to +1.8V.
Single-ended clock output.
No connect. Do not connect this pin to anything.
Connect to +1.8V.
Connect to +1.8V.
This pin should be connectd to GND (pin 15) through a 10µF capacitor.
Connect to +1.8V.
Ground Connect this pin to ground.
Ground Connect this pin to ground.
Ground Connect this pin to ground.
IDT®
PLL CLOCK MULTIPLIER
3
IDT5V80013
REV J 022312
IDT5V80013
PLL CLOCK MULTIPLIER
CLOCK MULTIPLIER
External Components
Decoupling Capacitor
As with any high-performance mixed-signal IC, the
IDT5V80013 must be isolated from system power supply
noise to perform optimally.
A decoupling capacitor of 0.01µF must be connected
between VDD and GND. It must be connected close to the
IDT5V80013 to minimize lead inductance. No external
power supply filtering is required for the IDT5V80013.
Series Termination Resistor
A 33Ω terminating resistor can be used next to the CLK pin.
The total on-chip capacitance is approximately 12 pF.
Absolute Maximum Ratings
Stresses above the ratings listed below can cause permanent damage to the IDT5V80013. These ratings, which
are standard values for IDT commercially rated parts, are stress ratings only. Functional operation of the device at
these or any other conditions above those indicated in the operational sections of the specifications is not implied.
Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical
parameters are guaranteed only over the recommended operating temperature range.
Item
Supply Voltage, VDD
All Inputs and Outputs
Ambient Operating Temperature (industrial temperature)
Storage Temperature
Soldering Temperature
5V
Rating
-0.5 V to VDD+0.5 V
-40 to +85° C
-65 to +150° C
260° C
Recommended Operation Conditions
Parameter
Ambient Operating Temperature (commercial)
Ambient Operating Temperature (industrial)
Power Supply Voltage (measured in respect to GND)
Min.
0
-40
+1.71
Typ.
–
–
+1.8
Max.
+70
+85
+1.89
Units
°
C
°
C
V
IDT®
PLL CLOCK MULTIPLIER
4
IDT5V80013
REV J 022312
IDT5V80013
PLL CLOCK MULTIPLIER
CLOCK MULTIPLIER
DC Electrical Characteristics
VDD=1.8 V ±5%
,
VDDO = 3.3 V
,
Ambient temperature -40 to +85° C, unless stated otherwise
Parameter
Operating Voltage
Output Voltage
Output High Voltage*
Output Low Voltage*
IDD Operating Supply Current
Input Capacitance
*Note: Guaranteed by design.
Symbol
VDD
VDDO
V
OH
V
OL
Conditions
Min.
1.71
3.135
Typ.
1.8
3.3
Max.
1.89
3.465
0.4
Units
V
V
V
V
mA
pF
I
OH
= -2 mA
I
OL
= 2 mA
No load
VDD-0.45
15
4
22
AC Electrical Characteristics
VDD=1.8 V ±5%, VDDO = 3.3 V,
Ambient Temperature -40 to +85° C, unless stated otherwise
Parameter
Output Frequency
Frequency Synthesis Error
Output Clock Rise Time
Output Clock Fall Time
Output Clock Duty Cycle
Short Term Cycle-to-Cycle Jitter
One Sigma Clock Period Jitter
Long Term Jitter
Aging
Power-up Time
Note: Measured with a 7pF load.
Symbol
Conditions
Min.
-50
Typ.
Max.
50
Units
MHz
ppm
ns
ns
See Page 2
t
OR
t
OF
t
OD
t
ja
t
js
0.8 to 2.0 V
2.0 to 0.8 V
VDD/2
CLK output
CLK output
CLK output
First year
1
1
45
50
75
15
TBD
5
10
45
55
100
%
ps
ps
ps
ppm
ms
IDT®
PLL CLOCK MULTIPLIER
5
IDT5V80013
REV J 022312
京公网安备 11010802033920号
EEWORLD
