EEWORLDEEWORLDEEWORLD

Part Number

Search

SMW31R8FT

Description
RESISTOR, WIRE WOUND, 3W, 1%, 200ppm, 1.8ohm, SURFACE MOUNT, 4122, CHIP
CategoryPassive components    The resistor   
File Size127KB,2 Pages
ManufacturerTE Connectivity
Websitehttp://www.te.com
Environmental Compliance
Download Datasheet Parametric View All

SMW31R8FT Overview

RESISTOR, WIRE WOUND, 3W, 1%, 200ppm, 1.8ohm, SURFACE MOUNT, 4122, CHIP

SMW31R8FT Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerTE Connectivity
package instructionCHIP
Reach Compliance Codeunknown
ECCN codeEAR99
structureRectangular
JESD-609 codee3
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature280 °C
Minimum operating temperature-55 °C
Package height5 mm
Package length10.5 mm
Package formSMT
Package width5.5 mm
method of packingTR
Rated power dissipation(P)3 W
Rated temperature25 °C
resistance1.8 Ω
Resistor typeFIXED RESISTOR
size code4122
surface mountYES
technologyWIRE WOUND
Temperature Coefficient200 ppm/°C
Terminal surfaceTin (Sn)
Terminal shapeWRAPAROUND
Tolerance1%
Operating Voltage500 V
SMD Moulded Power Resistor
Type SM Series
Type SM Series
Characteristics -
Electrical
Values SMF1:
Values SM_2:
Values SM_3:
Values SM_5:
Value Grid:
Resistance Tolerance:
Power Rating @ 25°C SMF1:
Power Rating @ 25°C SM_2:
Power Rating @ 25°C SM_3:
Power Rating @ 25°C SM_5:
Derating:
Max Operating Voltage SMF1:
Max Operating Voltage SM_2:
Max Operating Voltage SM_3:
Max Operating Voltage SM_5:
SM (Wire)
----
R10 – 200R
R10 – 300R
R10 - 500R
E24
1% or 5%
----
2.0 Watts
3.0 Watts
5.0 Watts
See Curve Below
----
300 Volts
500 Volts
500 Volts
300 Volts
1.0 Watt
SM (Metal Film)
10R – 2M
201R – 2M
301R – 2M
501R - 2M
Tyco Electronics CGS introduces a
surface mount power resistor suited to
meet today's circuit design needs. Each
size offers low profile case design with
flexible
tinned
copper
terminations for reliable solder joints.
All styles utilize a fully welded
construction technique, unlike other
designs that rely solely on tinned
termination
connections.
These
features allow the SM Series to
withstand the higher temperatures
associated
with
reflow,
vapour
phase, or infrared (IR) manufacturing
processes without degradation.
Characteristics -
Environmental
Test
Temperature Coefficient
of Resistance:
Short Time Overload:
Rated Load:
Insulation Resistance:
Load Life:
Humidity Load Life:
Condition
-55°C ~ +200°C
5 times of rated wattage for 5 sec.
Rated voltage for 30 minutes
500V megger.
70°C on-off cycle 1,000hrs.
40°C - 95% RH on-off cycle 500hrs.
SM (Wire)
± 200ppm /°C
± 1%
± 1%
10,000 MΩ
± 2%
± 2%
SM (Metal Film)
± 100ppm /°C
± 0.5%
± 0.5%
10,000 MΩ
± 1%
± 1%
Key Features
I
I
I
I
I
Low Profile Design
Available on Tape
Very Wide Value Range
Ideal for Power Circuitry
Available in 1, 2,3
or 5 Watts
Power Derating
100
Rated Load (%)
75
50
25
0
-80 -50 -40
0 20 40
80
120
160
200
240
280
Ambient Temperature (°C)
Maximum Allowable Body
Temperature
250
Temperature Rise (°C)
200
150
100
50
0
0
0.5
1.0
1.5
2.0
2.5
Power (W)
3.0
3.5
4.0
4.5
5.0
SMW1W
100°C
SMW2W
135°C
SMW5W
220°C
SMW3W
160°C
Literature No. 1773242
Issued: 05-09
Dimensions are shown for
reference purposes only.
Dimensions are in
millimetres unless
otherwise specified.
Specifications subject to
change.
tycoelectronics.com
passives.tycoelectronics.com

Recommended Resources

5# Analysis of Bluetooth routines on STM32WB development board
[i=s] This post was last edited by Beifang on 2019-5-13 12:49 [/i] 1. ST's SDK provides a relatively rich set of examples, but the examples for dual-core use have not been added yet. They should be ad...
北方 RF/Wirelessly
[Analog Electronics Course Test] + Measurement and Optimization of ADC Frequency Domain Indicators
[size=14px]Analog Electronics Course Selection Test[/size] [size=14px]Click on the Analog Electronics Course Selection Test directly to enter a dialog box, prompting you the field of interest, click o...
constant TI Technology Forum
Please recommend a low-power DC motor driver chip!
Requirements: A small motor H-bridge driver chip with a supply voltage of 5V and a current of about 300mA. The signal voltage is also 5V for the microcontroller pin. The package is preferably SOP-8. N...
bigbat Motor Drive Control(Motor Control)
Selection method and principle of infrared temperature sensor
[align=left][font="]I. Selection method[/font][/align][align=left]1. Working conditions and use environment[/align][align=left](1) Working conditions of infrared temperature sensors. Ambient temperatu...
xixingkeji Industrial Control Electronics
Several gadgets that RF engineers cannot miss
[p=25, null, left][color=rgb(51, 51, 51)][font=微软雅黑]For RF engineers, with the advent of 5G and the increase in spectrum, the design challenges they face are also growing. For this reason, efficient t...
alan000345 RF/Wirelessly
Application of TPS61046 dual output in optical communication
Optical communication applications often need to boost the +3.3V input power supply to obtain a set of positive and negative voltages, such as +/-20V. The common practice is to use two chips to genera...
qwqwqw2088 Analogue and Mixed Signal

Popular Articles

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号