ANALOG DIODE
PHASE SHIFTERS
CONTINUOUSLY VARIABLE — 0.1–18 GHz
GENERAL INFORMATION
An analog phase shifter continuously changes the phase of a
microwave signal by varying a D.C. voltage. Since the D.C. voltage
applied to the diode is a reverse bias, the current drain is negligible
(typically less than 10 microamps). A balanced stripline configuration
keeps the VSWR and amplitude ripple to a minimum for all values of
phase.
SERIES PQ
GENERAL SPECIFICATIONS
Frequency Coverage:
RF impedance:
D.C. Voltage:
0.1 to 18.0 GHz
50 OHMS.
0 volts to +28 volts (standard), or 0 volts
to –28 volts (optional) will vary the phase
of any of the models over the minimum
phase shift listed
10 mW peak or CW, operating. Destruct
level is 1 W, CW, 100 W peak.
The units can be used over a –55°C to
+85°C temperature range. However, the
phase will change either ±5° or ±5%,
whichever is greater. If temperature com-
pensation is required, this can be done on
request. With compensation, the variation
can be held to ±1° or ±1%, whichever is
greater, from –55°C to +85°C. The size
remains the same. If compensation is
desired, add a suffix T to the model num-
ber (e.g., PQ-17T).
Series PQ phase shifters can be driven
from any phase value to any other value
in 10 nanoseconds. With linearizers, the
response time is 50 nanoseconds. With
temperature compensation the response
time is 100 nanoseconds.
SMA
PHASE SHIFT (DEGREES)
150
120
90
60
30
PHASE
SHIFT
0
5
10
15
20
25
30
1.0
INSERTION LOSS (dB)
.8
.6
.4
.2
0
VOLTAGE (V)
RF Power:
Temperature Information:
INSERTION
LOSS
Switching Speed:
Fig. 1
Typical Phase & Insertion Loss vs. Voltage Curves for PQ-31
Connectors:
Notes:
1. LINEARIZATION: For phase shifters with linearizers add a suffix L
to the model number (e.g., PQ-23L). Linearity is ±2.0° for phase
shifters for 150° or less, and ±4° for phase shifters between 150°
and 360°. With linearization, DC voltages of ±15V at ±30mA are
required. The control voltage is 0–10 volts. A control voltage of 0–5
volts can be supplied at no additional cost, by adding a suffix 5 to
the model number (e.g. PQ-23L5). Linearity is measured at f
c
.
2. PHASE FLATNESS: The phase shift varies with frequency at any
voltage setting. This variation, referenced to 0° at 0 volts for each
frequency, is approximately ±15% for octave models, ± 10% for
models with 25% bandwidth, and ±7.5% for models with a 10%
bandwidth.
3. A connector, (SMA Female) is available in place of the bias pin at
no extra charge. This will be placed at the center of the surface
marked F on the drawing. This is the 0.38
×
A surface. If a SMA
Female is desired, add suffix C to the model number (e.g., PQ-
23C).
4. Monotonicity guaranteed for all models.
S (DEG)
PHASE SHIFT
yyyyyyyyyyyyyyyyyyy
,,,,,,,,,,,,,,,,,,,
yyyyyyyyyyyyyyyyyyy
,,,,,,,,,,,,,,,,,,,
yyyyyyyyyyyyyyyyyyy
,,,,,,,,,,,,,,,,,,,
160
,,,,,,,,,,,,,,,,,,,
yyyyyyyyyyyyyyyyyyy
yyyyyyyyyyyyyyyyyyy
,,,,,,,,,,,,,,,,,,,
yyyyyyyyyyyyyyyyyyy
,,,,,,,,,,,,,,,,,,,
yyyyyyyyyyyyyyyyyyy
,,,,,,,,,,,,,,,,,,,
yyyyyyyyyyyyyyyyyyy
,,,,,,,,,,,,,,,,,,,
yyyyyyyyyyyyyyyyyyy
100
,,,,,,,,,,,,,,,,,,,
yyyyyyyyyyyyyyyyyyy
,,,,,,,,,,,,,,,,,,,
yyyyyyyyyyyyyyyyyyy
,,,,,,,,,,,,,,,,,,,
yyyyyyyyyyyyyyyyyyy
,,,,,,,,,,,,,,,,,,,
yyyyyyyyyyyyyyyyyyy
,,,,,,,,,,,,,,,,,,,
40
,,,,,,,,,,,,,,,,,,,
yyyyyyyyyyyyyyyyyyy
yyyyyyyyyyyyyyyyyyy
,,,,,,,,,,,,,,,,,,,
yyyyyyyyyyyyyyyyyyy
,,,,,,,,,,,,,,,,,,,
yyyyyyyyyyyyyyyyyyy
,,,,,,,,,,,,,,,,,,,
0.4
1.0
1.6
BIAS VOLTAGE VB (V)
Fig. 2
Phase shift characteristic of PQ-45.
KEY:
Inches[Millimeters] .XX ±.03 .XXX ±.010 [.X ±0.8 .XX ±0.25]
60 South Jefferson Road, Whippany, NJ 07981
Tel: 973-887-8100 • Fax: 973-884-0445
email: sales@mcekdi-integrated.com
See us on the web @ www.mcekdi-integrated.com
11-5-02
ANALOG DIODE
PHASE SHIFTERS
CONTINUOUSLY VARIABLE — 0.1–18 GHz
F SURFACE
0.25[6,3]
GROUND
E
BIAS PIN
0.25[6,3]
C.V.
+15V
E
SERIES PQ
–15V
GND
SMA
FEMALE
TYP.
D
B
SMA
FEMALE
TYP.
D
B
RF
C
A
RF
0.20
[5,1]
RF
0.40
[10,2]
0.10[2,5]
TYP.
F
0.093[2,36]
DIA. THRU
3 MOUNTING
HOLES
0.38[9,7]
TYP.
0.10[2,5]
TYP.
1.00
[25,4]
C
A
0.125[3,18]
DIA. THRU
3 MOUNTING
HOLES
F
0.38[9,7]
TYP.
OUTLINE WITHOUT LINEARIZER
OUTLINE WITH LINEARIZER
ELECTRICAL PERFORMANCE
Phase
Shift
Insertion Amplitude
Note 2
Loss
Ripple
Outline
Frequency Minimum Maximum Maximum
VSWR
No
With
Model No.* Range GHz Degrees
dB
± dB
Maximum Linearizer Linearizer
PQ-12
0.1–0.2
50
0.6
0.15
1.35
1
1
PQ-14
PQ-17
PQ-27
PQ-28
PQ-31
PQ-33
PQ-34
PQ-39
PQ-44
PQ-45
PQ-49
PQ-59
PQ-60
PQ-65
PQ-66
PQ-72
PQ-73
PQ-74
PQ-94
0.2–0.4
0.25–0.5
0.5–1.0
0.5–1.0
0.95–1.25
1.0–2.0
1.0–2.0
1.7–2.4
2.0–4.0
2.0–4.0
2.2–2.3
4.0–8.0
4.0–8.0
6.0–18.0
7.0–12.4
8.0–12.4
8.0–10.0
8.0–18.0
16.0–17.0
50
360
180
360
120
60
360
15
180
360
180
40
360
180
360
60
180
360
50
0.6
4.5
3.0
4.5
1.2
0.8
4.5
0.7
3.0
5.0
2.0
1.2
8.0
12.0
12.0
2.0
5.0
17.0
2.0
0.15
1.25
0.4
1.25
0.15
0.15
1.5
0.05
0.50
1.5
0.30
0.25
1.5
2.0
2.0
0.50
1.0
3.5
0.20
1.35
1.70
1.50
1.75
1.40
1.50
1.80
1.40
1.60
1.90
1.50
1.60
1.90
2.5
2.20
1.75
1.75
2.50
1.65
1
10
3
4
1
2
8
2
3
5
3
2
9
7
9
2
7
9
2
1
10
3
4
1
6
4
6
3
5
3
6
9
7
9
6
7
9
6
MECHANICAL OUTLINES
Out-
line
1
2
3
4
5
6
7
8
9
10
A
B
C
D
in
in
in
in
[mm]
[mm]
[mm]
[mm]
2.75
2.25
1.38
2.050
[69,91] [57,15] [35,05] [52,07]
1.25
2.00
0.63
1.800
[31,75] [50,8]
5.00
2.00
[127,0] [50,8]
7.75
[196,8]
6.50
[165,1]
2.00
[50,8]
3.00
[76,2]
6.50
[165,1]
5.00
[127,0]
7.75
[196,8]
2.50
[63,5]
2.00
[50,8]
2.00
[50,8]
2.00
[50,8]
2.50
[63,5]
2.00
[50,8]
2.50
[63,5]
[16,0]
N/A
4 holes
[45,7]
1.800
[45,7]
E
F
in
in
[mm]
[mm]
2.250 0.53
[57,15] [13,46]
0.750 0.25
[19,1]
4.500
[114,3]
[6,4]
0.25
[6,4]
0.25
[6,4]
0.25
[6,4]
0.25
[6,4]
0.25
[6,4]
0.25
[6,4]
0.50
[12,7]
0.75
N/A
2.300
7.250
4 holes [58,42] [184,15]
N/A
1.800
6.000
4 holes
1.00
[25,4]
[45,7]
1.800
[45,7]
[152,4]
1.500
[38,1]
1.50
1.800
2.500
[38,1] [45,7] [63,5]
N/A
2.300
6.000
4 holes [58,42] [152,4]
N/A
4 holes
N/A
1.800
[45,7]
2.300
4.500
[114,3]
7.250
4 holes [58,42] [184,15] [19,1]
*OPTIONS: (Add to Model No.)
T
Temp. Comp.
L
Linearization
C
Bias Connector — SMA
5
0 to 5 Volts Control Voltage for Linearized Models.
KEY:
Inches[Millimeters] .XX ±.03 .XXX ±.010 [.X ±0.8 .XX ±0.25]
An MCE Company
CORPORATION
TRIANGLE
60 South Jefferson Road, Whippany, NJ 07981
Tel: 973-887-8100 • Fax: 973-884-0445
E-Mail: kdisales@aol.com
See us on the web @ www.kditriangle.com
10/98
京公网安备 11010802033920号
EEWORLD
