The sum of DC voltage and the peak AC voltage must not exceed the rated voltage of the capacitor
Performance
Performance
Capacitance Change
Equivalent Series Resistance
Leakage Current
The following specifications will be satisfied when the capacitor is tested at +20°C:
≤ 160 V
> 160 V
Does not exceed 200% of the initial value
Does not exceed leakage current limit
Within 15% of the initial value
Within 10% of the initial value
Dimensions – Millimeters
Dimensions in inches
Size Code
D2C
D2L
D3C
D3L
D4C
D4L
D5C
D5L
K2C
K2L
K3C
K3L
K4C
K4L
K5C
K5L
D
±0.031
1.375
1.375
1.375
1.375
1.375
1.375
1.375
1.375
2
2
2
2
2
2
2
2
L
±0.062
2.125
2.625
3.125
3.625
4.125
4.625
5.125
5.625
2.125
2.625
3.125
3.625
4.125
4.625
5.125
5.625
LT
±0.039
2.420
2.930
3.440
3.960
4.430
4.940
5.450
5.960
2.420
2.930
3.440
3.960
4.430
4.940
5.410
5.960
S
±0.019
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.875
0.875
0.875
0.875
0.875
0.875
0.875
0.875
V
Nominal
0.315
0.315
0.315
0.315
0.315
0.315
0.315
0.315
0.539
0.539
0.539
0.539
0.539
0.539
0.539
0.539
Mounting
Stud (M x H)
±0.039
M8 x 0.472
M8 x 0.472
M8 x 0.472
M8 x 0.472
M8 x 0.472
M8 x 0.472
M8 x 0.472
M8 x 0.472
M12 x 0.63
M12 x 0.63
M12 x 0.63
M12 x 0.63
M12 x 0.63
M12 x 0.63
M12 x 0.63
M12 x 0.63
Mounting Clip
V3/H2/UTE2736
V3/H2/UTE2736
V3/H2/UTE2736
V3/H2/UTE2736
V3/H2/UTE2736
V3/H2/UTE2736
V3/H2/UTE2736
V3/H2/UTE2736
V4/UTE2737
V4/UTE2737
V4/UTE2737
V4/UTE2737
V4/UTE2737
V4/UTE2737
V4/UTE2737
V4/UTE2737
Weight
Ounces
2.8
3.3
4
4.6
5.3
5.8
6.5
7.2
5.8
7.1
8.5
9.7
11.1
12.3
13.6
15
Note: Add 0.015 inches to D and 0.045 inches to L for Sleeving
3.5 inch diameter cans available upon request. LT listed is for A-type termination code. Information for other termination codes is available upon request.
Note: Add 0.015 inches to D and 0.045 inches to L for Sleeving
3.5 inch diameter cans available upon request. LT listed is for A-type termination code. Information for other termination codes is available upon request.
1. When using a module, we need to initialize it accordingly and set the functions we are going to use.
Divided into three parts----
1) Mailbox initialization configuration: First, you should determin...
Using timer interrupt to realize variable frequency flashing of LED lightsThe example is relatively simple, and the source code is directly posted.
#include "DSP2833x_Device.h" // DSP2833x Headerfile ...
Using STM32F103VET6 microcontroller, DAC+DMA+TIM2 trigger mode, channel 1 outputs sine wave, refer to the routine configuration, but there is no signal output, the hardware is checked and it is normal...
[i=s]This post was last edited by yjtyjt on 2019-9-17 20:36[/i]Showing off the Jingdong E-card exchanged with E-coins. I liked some of the coins and exchanged them for a 400 yuan E-card on Jingdong. W...
[i=s]This post was last edited by elec32156 on 2020-4-19 16:33[/i]The figure shows 74HC165 shift registers, which are connected in series. One is 8 bits, and two can achieve 16-bit data output (ultima...
[i=s]This post was last edited by elec32156 on 2020-2-18 10:54[/i]As shown in the following PMOS switch circuit, there are some unclear points during the switching process:
1) After the transistor is ...