SMD Chip LED
Package Dimensions:
All dimensions are in mm
Tolerance: ±0.1mm
Absolute Maximum Ratings at Ta=25°C
Parameter
Power Dissipation
Reverse Voltage
D.C. Forward Current
Pulsed Forward Current (1 / 10 Duty Cycle, 0.1ms Pulse Width)
Operating Temperature Range
Storage Temperature Range
Soldering Temperature
Symbol
P
d
V
r
If
If (Peak)
Topr.
Tstg.
Tsld.
78
5
30
80
-40 to +80
-40 to +85
Reflow Soldering: 260°C for 10sec.
Rating
Unit
°C
V
mA
mA
°C
°C
Electrical & Optical Characteristics: Hyper Red
Parameter
Luminous Intensity
Forward Voltage
Peak Wavelength
Dominent Wavelength
Reverse Current
Viewing Angle
Spectrum Line Halfwidth
Symbol
Iv
Vf
λp
λd
Ir
2θ ½
Δλ
Condition
If = 20mA
If = 20mA
If = 20mA
If = 20mA
Vr = 5V
If = 20mA
If = 20mA
Min.
-
1.9
-
-
-
-
-
Typ.
11
-
567
572
-
140
30
Max.
-
2.6
-
-
100
-
-
Unit
mcd
V
nm
nm
μA
deg
nm
Note: 1. The data is tested by an IS tester
2. Customer’s special requirements are also welcome.
www.element14.com
www.farnell.com
www.newark.com
Page <1>
27/06/12
V1.0
SMD Chip LED
Recommended Storage Environment:
•
•
•
Temperature: 5°C to 30°C (41°F to 86°F)
Humidity: 60% RH Max.
Use within 7 days after opening of sealed vapour/ESD barrier bags
If moisture absorbent material (silica gel) has faded away or LEDs have exceeded the storage time, baking treatment should
be performed using the following conditions:
• Baking Treatment : 60 ± 5°C for 24 hours
• Fold the opened bag firmly and keep in dry environment
www.element14.com
www.farnell.com
www.newark.com
Page <3>
27/06/12
V1.0
SMD Chip LED
Reflow Soldering
Recommended use of upper and lower heater type reflow furnace.
• 260°C max for up to 10 seconds, one time only
• Pre-heat is 150°C max for up to 2 minutes max
• In case of screen-printing, keep metal mask thickness between 0.2mm and 0.3mm
Cleaning
Surface condition of this device may change when organic solvents such as trichloroethylene or acetone were applied.
•
Avoid using organic solvent
•
Recommend ultrasonic method 300W max.
Packaging
•
•
EIA-481A standard package
In 8mm tape on 4000pcs diameter reels sealed in vapour/ESD barrier bags
Reflow Temp / Time:
Part Number Table
LED Chip
Material
GaP / GaP
Emitting Colour
Green
Lens Colour
White diffused
Part Number
703-0104
Important Notice :
This data sheet and its contents (the “Information”) belong to the members of the Premier Farnell group of companies (the “Group”) or are licensed to it. No licence is granted
for the use of it other than for information purposes in connection with the products to which it relates. No licence of any intellectual property rights is granted. The Information is subject to change
without notice and replaces all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness, any
error in or omission from it or for any use made of it. Users of this data sheet should check for themselves the Information and the suitability of the products for their purpose and not make any
assumptions based on information included or omitted. Liability for loss or damage resulting from any reliance on the Information or use of it (including liability resulting from negligence or where the
Group was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Group’s liability for death or personal injury resulting from its negligence.
Multicomp is the registered trademark of the Group. © Premier Farnell plc 2012.
www.element14.com
www.farnell.com
www.newark.com
Page <4>
27/06/12
V1.0
Industrial Control Electronics
京公网安备 11010802033920号
EEWORLD
