EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

54242-804-12-1450

Description
Board Stacking Connector, 12 Contact(s), 2 Row(s), Male, Straight, 0.1 inch Pitch, Surface Mount Terminal, Locking, Black Insulator, Receptacle,
CategoryThe connector    The connector   
File Size83KB,1 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Download Datasheet Parametric View All

54242-804-12-1450 Overview

Board Stacking Connector, 12 Contact(s), 2 Row(s), Male, Straight, 0.1 inch Pitch, Surface Mount Terminal, Locking, Black Insulator, Receptacle,

54242-804-12-1450 Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
MakerAmphenol
Reach Compliance Codecompliant
ECCN codeEAR99
body width0.169 inch
subject depth0.571 inch
body length1.2 inch
Body/casing typeRECEPTACLE
Connector typeBOARD STACKING CONNECTOR
Contact to complete cooperationGOLD (15) OVER NICKEL (50)/NICKEL PALLADIUM GOLD (15) OVER NICKEL (50)
Contact completed and terminatedTin/Lead (Sn/Pb) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
DIN complianceNO
Filter functionNO
IEC complianceNO
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialTHERMOPLASTIC
JESD-609 codee0
MIL complianceNO
Manufacturer's serial number54242
Plug contact pitch0.1 inch
Match contact row spacing0.1 inch
Mixed contactsNO
Installation option 1LOCKING
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded2
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
OptionsGENERAL PURPOSE
PCB contact patternRECTANGULAR
PCB contact row spacing5.461 mm
Plating thickness15u inch
Rated current (signal)3 A
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal pitch2.54 mm
Termination typeSURFACE MOUNT
Total number of contacts12
UL Flammability Code94V-0
How to calculate the input impedance of this full-bridge rectifier?
The green box is equivalent to VEQ, and the rest of the rectifier and BUCK circuit is equivalent to this Rload. So how do I calculate this Rload? The switch signal parameters are shown in Figure 1....
fishiscat Analogue and Mixed Signal
Introduction to resistor selection experience
Introduction to the selection experience of resistors...
fighting Analog electronics
Design of receiving circuit for radio remote control transmitter
Although OOK modulation has poor performance, its circuit is simple, easy to implement, and stable in operation. Therefore, it has been widely used. Such circuits are almost always used in car and mot...
Aguilera Wireless Connectivity
【Portable Environmental Status Detector】Use of GPIO port
When it comes to a new development board, the GPIO port is the best starting point, and the ESP32-S2-Kaluga-1 kit is no exception. A basic example provided in the routine is to light up the WS2812, bu...
jinglixixi DigiKey Technology Zone
How to Layout a Circuit Board for an Op Amp
During the circuit design process, application engineers often overlook the layout of the printed circuit board (PCB). The problem often encountered is that the circuit schematic is correct, but it do...
ohahaha PCB Design
Research on Charging Method of Lead-acid Battery
[i=s]This post was last edited by qwqwqw2088 on 2021-7-26 08:06[/i]Lead-acid batteries have been widely used due to their low manufacturing cost, large capacity and low price. However, if used imprope...
qwqwqw2088 Power technology

Technical ResourceMore

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号