EEWORLDEEWORLDEEWORLD

Part Number

Search

H2R15ST29JPM53

Description
D Type Connector, 15 Contact(s), Female, 0.109 inch Pitch, Solder Terminal, #4-40, Plug
CategoryThe connector    The connector   
File Size698KB,17 Pages
ManufacturerThomas & Betts Corporation
Websitehttp://www.tnb.com/
Download Datasheet Parametric View All

H2R15ST29JPM53 Overview

D Type Connector, 15 Contact(s), Female, 0.109 inch Pitch, Solder Terminal, #4-40, Plug

H2R15ST29JPM53 Parametric

Parameter NameAttribute value
MakerThomas & Betts Corporation
Reach Compliance Codeunknown
ECCN codeEAR99
Other featuresGNDING STRAP, TOP ONLY
body width0.415 inch
subject depth0.24 inch
body length1.552 inch
Body/casing typePLUG
Contact to complete cooperationAU ON NI
Contact completed and terminatedGOLD
Contact point genderFEMALE
Contact materialCOPPER ALLOY
contact modeSTAGGERED
Contact resistance10 mΩ
Contact styleRND PIN-SKT
Dielectric withstand voltage1000VAC V
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialGLASS FILLED POLYESTER
Manufacturer's serial numberH2
Plug contact pitch0.109 inch
Match contact row spacing0.112 inch
Installation option 1#4-40
Installation option 2STANDOFF
Installation methodSTRAIGHT
Installation typeBOARD
PCB row number2
Number of rows loaded2
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
PCB contact patternSTAGGERED
PCB contact row spacing2.8448 mm
Plating thickness30u inch
Rated current (signal)5 A
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal length0.125 inch
Terminal pitch2.7686 mm
Termination typeSOLDER
Total number of contacts15
Printed from www.freetradezone.com, a service of Partminer, Inc.
This Material Copyrighted By Its Respective Manufacturer
Free evaluation | Ateli AT-START-F403A helps you explore and discover ARM Cortex-M4F with FPU core
Development board for this activity: AT-START-F403A From: Arteli Technology (Chongqing) Co., Ltd.Number of development boards: 10AT-START-F403AAT-START-F403A helps you explore the high performance fea...
okhxyyo Domestic Chip Exchange
How to configure the input and output of a GPIO in the TMS320C6000 series DSP?
1) Enable the general purpose input and output port peripheral (GPIO). // Enable the GPIO module (the corresponding peripheral module can also be enabled in BootLoader) PSCModuleControl(SOC_PSC_1_REGS...
Jacktang DSP and ARM Processors
Working conditions and working characteristics of switching power supply
Working conditions of switching power supply:   1. Switch: Power electronic devices work in a switching state rather than a linear state   2. High frequency: Power electronic devices operate at high f...
唯小样 Power technology
Let’s discuss some common misunderstandings about GaN.
I recently saw an article by Qorvo introducing several major misunderstandings about GaN, which made me feel deeply moved.First of all, the issue that everyone considers is the cost. In the engineerin...
alan000345 RF/Wirelessly
RISC-V MCU Development (IV): Compilation Configuration
In embedded development, after we have completed the project creation, code editing and other operations, we can start the project compilation. For projects created using built-in project templates or...
Moiiiiilter MCU
【CH579M-R1】+ driving LCD5110 display
After a day of debugging, the LCD5110 display finally drove successfully. The program was ported from STM32, and a logic analyzer was used to adjust the timing. During the debugging process, I made a ...
hujj Domestic Chip Exchange

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号