1285-3-54-2 datasheet, PDF - EEWORLD Datasheet

1285-3-54-2: DescriptionBoard Connector, 54 Contact(s), 2 Row(s), Female, Straight, 0.05 inch Pitch, Solder Terminal, Locking; CategoryThe connector The connector; File Size156KB，1 Pages; ManufacturerConexcon Group; Environmental Compliance

Download Datasheet Parametric View All

1285-3-54-2 Overview

Board Connector, 54 Contact(s), 2 Row(s), Female, Straight, 0.05 inch Pitch, Solder Terminal, Locking

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Reach Compliance Code	unknow
body width	0.197 inch
subject depth	0.335 inch
body length	1.35 inch
Connector type	BOARD CONNECTOR
Contact to complete cooperation	AU ON NI
Contact point gender	FEMALE
Contact material	PHOSPHOR BRONZE
contact mode	RECTANGULAR
Contact resistance	20 mΩ
Contact style	SQ PIN-SKT
Dielectric withstand voltage	300VAC V
Durability	50 Cycles
maximum insertion force	1.946 N
Insulation resistance	1000000000 Ω
Manufacturer's serial number	1285
Plug contact pitch	0.05 inch
Match contact row spacing	0.1 inch
Installation option 1	LOCKING
Installation method	STRAIGHT
Installation type	BOARD
Number of connectors	ONE
PCB row number	2
Number of rows loaded	2
Maximum operating temperature	105 °C
Minimum operating temperature	-40 °C
PCB contact pattern	RECTANGULAR
PCB contact row spacing	2.54 mm
Plating thickness	FLASH inch
polarization key	POLARIZED HOUSING
Rated current (signal)	1 A
Guideline	UL
reliability	COMMERCIAL
Terminal length	0.118 inch
Terminal pitch	1.27 mm
Termination type	SOLDER
Total number of contacts	54
Evacuation force-minimum value	.14734 N
Base Number Matches	1

The microcontroller cannot be programmed. I checked and it said it was locked, but when I unlocked it, it popped up a pop-up saying there was something wrong with the unlock file. I checked the flash and it was like this...: ...; 瓜皮不瓜皮 51mcu

Technical article | How to use J-Link to burn SPI Flash: J-Link not only supports the burning of the Flash on the MCU , but also can directly burn the SPI Flash through the SPI protocol. Because the SPI protocol is used , even if the MCU connected to the SP...; MamoYU Integrated technical exchanges

Low power consumption comparison between STM8L and MSP430: After comparing actual products, STM8L's low power consumption is far better than MSP430. I'll record it here. Different opinions are welcome. The test environment is as follows: 1. External crystal o...; Aguilera Microcontroller MCU

Drag-and-drop stepper motor programmable controller + PLC-like: ...; net2uizoo DIY/Open Source Hardware

Pengfeng Technology RVBoards-Nezha (RISC-V SBC) Allwinner Development Board Introduction 4: Perf-V IDE Introduction and Installation Instructions...; 火辣西米秀 Domestic Chip Exchange

Share the SPWM code written by DSPF28335 with everyone: The source program is as follows:/** main.c*/ #include "DSP28x_Project.h"// Device Headerfile and Examples Include File // Prototype statements for functions found within this file. void InitEPwm1Exam...; fish001 DSP and ARM Processors

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components