EEWORLDEEWORLDEEWORLD

Part Number

Search

MC12093

Description
ECL SERIES, PRESCALER, PDSO8
Categorysemiconductor    logic   
File Size236KB,3 Pages
ManufacturerMotorola ( NXP )
Websitehttps://www.nxp.com
Download Datasheet Parametric View All

MC12093 Overview

ECL SERIES, PRESCALER, PDSO8

MC12093 Parametric

Parameter NameAttribute value
Number of functions1
Number of terminals8
Maximum operating temperature85 Cel
Minimum operating temperature-40 Cel
Maximum supply/operating voltage5.5 V
Minimum supply/operating voltage2.7 V
Processing package descriptionSOIC-8
stateACTIVE
packaging shapeRectangle
Package SizeSMALL OUTLINE
surface mountYes
Terminal formGULL WING
Terminal spacing1.27 mm
terminal coatingtin lead
Terminal locationpair
Packaging MaterialsPlastic/Epoxy
Temperature levelINDUSTRIAL
seriesemitter coupled logic circuit
Logic IC typecrossover
Number of data clock inputs1
Max-Min frequency1100 MHz
Freescale Semiconductor, Inc.
Order this document by MC12093/D
MC12093
ARCHIVED BY FREESCALE SEMICONDUCTOR, INC. 2005
÷
2,
÷
4,
÷
8 1.1GHz Low Power
Prescaler with Stand-By Mode
The MC12093 is a single modulus prescaler for low power frequency
division of a 1.1 GHz high frequency input signal. Motorola’s advanced
MOSAIC™ V technology is utilized to acheive low power dissipation of
6.75 mW at a minimum supply voltage of 2.7 V.
On–chip output termination provides output current to drive a 2.0 pF
(typical) high impedance load. If additional drive is required for the prescaler
output, an external resistor can be added parallel from the OUT pin to GND
to increase the output power. Care must be taken not to exceed the
maximum allowable current through the output.
Divide ratio control inputs SW1 and SW2 select the required divide ratio of
÷2, ÷4,
or
÷8.
Stand–By mode is featured to reduce current drain to 50
µA
typical when
the standby pin SB is switched LOW disabling the prescaler.
1.1 GHz Toggle Frequency
Supply Voltage 2.7 V to 5.5 Vdc
Low Power 3.0 mA Typical
Operating Temperature –40 to 85°C
Divide by 2, 4 or 8 Selected by SW1 and SW2 Pins
On–Chip Termination
MECL PLL COMPONENTS
÷2, ÷4, ÷8
LOW POWER
PRESCALER
WITH STAND–BY MODE
SEMICONDUCTOR
TECHNICAL DATA
ARCHIVE INFORMATION
ARCHIVED BY FREESCALE SEMICONDUCTOR, INC. 2005
8
1
D SUFFIX
PLASTIC PACKAGE
CASE 751
(SO–8)
MOSAIC V is a trademark of Motorola
PIN CONNECTIONS
SW
L
H
L
H
SW2
L
L
H
H
Divide Ratio
8
4
4
2
IN
VCC
SW2
OUT
1
2
3
4
8
7
6
5
FUNCTIONAL TABLE
IN
SB
SW1
Gnd
NOTES:
1. SW1 & SW2: H = (VCC – 0.5 V) to VCC; L = Open.
2. SB: H = 2.0 V to VCC, L = GND to 0.8 V.
(Top View)
A LOW on the Stand–By Pin 7 disables the device.
Function Chart
ORDERING INFORMATION
IN
÷2
÷4
÷8
Device
MC12093D
Operating
Temp Range
TA = –40 to 85°C
Package
SO–8
©
Motorola, Inc. 1998
Rev 4
MOTOROLA RF/IF DEVICE DATA
For More Information On This Product,
1
Go to: www.freescale.com
ARCHIVE INFORMATION
Freescale Semiconductor, Inc...
Working principle of lithium battery equalization circuit
[i=s] This post was last edited by qwqwqw2088 on 2019-2-11 14:23 Edit[/i] [size=4][color=#000000][backcolor=white] The development of new energy and electric vehicles will use lithium batteries with r...
qwqwqw2088 Analogue and Mixed Signal
[SAMR21 new gameplay] 31. Using NVM storage
[i=s]This post was last edited by dcexpert on 2019-10-17 10:55[/i]In SAMR21, part of the flash space can be used to simulate EEPROM, which is called NVM (Non-Volatile Memory). Using EEPROM is simpler ...
dcexpert MicroPython Open Source section
[ATmega4809 Curiosity Nano Review] Buttons
On the ATmega4809 Curiosity Nano, the button uses PF6, which is also the RST pin and is set to GPIO mode by default. Because there is a 100K pull-up resistor R200 on PF6, there is no need to set the i...
dcexpert MCU
Have you fallen into these customer support "pitfalls"? Read the story, write a comment, grab a post and win a gift!
[align=left][b][font=微软雅黑][size=3]No way to get support in the middle of the night, time-consuming to return software to the factory for upgrading, too low efficiency of customer service communication...
EEWORLD社区 Test/Measurement
About rail-to-rail op amps
[size=4]1. The so-called rail-to-rail operational amplifier refers to an amplifier whose input and output voltage swings are very close to or almost equal to the power supply voltage. [/size] [size=4]...
Jacktang Analogue and Mixed Signal
【TGF4042 signal generator】+ Load capacity test
I have used a function generator from manufacturer A before. Its output protection is quite complete. If the output probe encounters external interference, such as accidentally connecting to a DC powe...
飞鸿浩劫 Test/Measurement

Technical ResourceMore

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号