DATASHEET
PLL CLOCK MULTIPLIER WITH SS
Description
The IDT5V80015 is the most cost effective way to generate
a high-quality, high-frequency clock output.
Using Phase-Locked Loop (PLL) techniques, the device
employs IDT’s propietary MEMs oscillator technology to
produce common output frequencies for consumer,
computing, and embedded applications that require center
spread spectrum to reduce system EMI.
IDT5V80015
Features
•
Packaged in a small form factor 16-pin QFN
•
Eliminates the need for an external crystal or input clock
•
•
•
•
•
•
•
•
source
Max. +50ppm error on CLK output
Typical ±75 ps short term cycle-cycle jitter
Center spread spectrum capability to reduce EMI
Output voltage of 3.3 V
Operating voltage of 1.8V
Supports industrial temperature range
Supports output frequency on CLK up to 130MHz
Advanced, low-power CMOS process
Block Diagram
VDD
VDDO
S1:S0
MEMs
OScillator
PLL Clock
Synthesis
with Spread
Spectrum
CLK
GND
IDT®
PLL CLOCK MULTIPLIER
1
IDT5V80015
REV D 022312
IDT5V80015
PLL CLOCK MULTIPLIER
CLOCK MULTIPLIER
Pin Assignment
CAP-IN
GND
VDD
VDD
SS CLK Output Frequency/Part Number Table
Frequency
27 MHz
50 MHz
66.6666 MHz
122.8 MHz
Orderable Part Number
5V80015-027NLGI
5V80015-050NLGI
5V80015-666NLGI
5V80015-122NLGI
VDD
S1
S0
OE
1
13
VDD
NC
GND
Note: Contact IDT for any other frequencies.
5
9
SSCLK
16-pin QFN
Spread Spectrum Selection Table
S1 S0
0
0
1
1
0
1
0
1
Spread Amount
No spread
+/-0.5%
+/-1.0%
+/-1.5%
VDDO
GND
VDD
VDD
Direction
—
Center
Center
Center
*
Default setting is S1:S0 =000
IDT®
PLL CLOCK MULTIPLIER
2
IDT5V80015
REV D 022312
IDT5V80015
PLL CLOCK MULTIPLIER
CLOCK MULTIPLIER
Pin Descriptions
Pin
Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Pin
Name
VDD
S1
S0
OE
VDDO
VDD
VDD
GND
SS CLK
GND
NC
VDD
VDD
CAP-IN
GND
VDD
Pin
Type
Power
Input
Input
Input
Power
Power
Power
Output
–
Power
Power
–
Power
Connect to +1.8V.
Pin Description
Input select pin for spread spectrum selection. See table above. Internal
pull-down resistor.
Input select pin for spread spectrum selection. See table above. Internal
pull-down resistor.
Output enable for SS CLK output.
Connect to +3.3V.
Connect to +1.8V.
Connect to +1.8V.
Single-ended clock output.
No connect. Do not connect this pin to anything.
Connect to +1.8V.
Connect to +1.8V.
This pin should be connected to GND (pin 15) through a 10µF capacitor
Connect to +1.8V.
Ground Connect this pin to ground.
Ground Connect this pin to ground.
Ground Connect this pin to ground.
IDT®
PLL CLOCK MULTIPLIER
3
IDT5V80015
REV D 022312
IDT5V80015
PLL CLOCK MULTIPLIER
CLOCK MULTIPLIER
External Components
Decoupling Capacitor
As with any high-performance mixed-signal IC, the
IDT5V80015 must be isolated from system power supply
noise to perform optimally.
A decoupling capacitor of 0.01µF must be connected
between VDD and GND. It must be connected close to the
IDT5V80015 to minimize lead inductance. No external
power supply filtering is required for the IDT5V80015.
Series Termination Resistor
A 33Ω terminating resistor can be used next to the CLK pin.
The total on-chip capacitance is approximately 12 pF.
Absolute Maximum Ratings
Stresses above the ratings listed below can cause permanent damage to the IDT5V80015. These ratings, which
are standard values for IDT commercially rated parts, are stress ratings only. Functional operation of the device at
these or any other conditions above those indicated in the operational sections of the specifications is not implied.
Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical
parameters are guaranteed only over the recommended operating temperature range.
Item
Supply Voltage, VDD
All Inputs and Outputs
Ambient Operating Temperature (industrial temperature)
Storage Temperature
Soldering Temperature
5V
Rating
-0.5 V to VDD+0.5 V
-40 to +85° C
-65 to +150° C
260° C
Recommended Operation Conditions
Parameter
Ambient Operating Temperature (commercial)
Ambient Operating Temperature (industrial)
Power Supply Voltage (measured in respect to GND)
Min.
0
-40
+1.71
Typ.
–
–
+1.8
Max.
+70
+85
+1.89
Units
°
C
°
C
V
IDT®
PLL CLOCK MULTIPLIER
4
IDT5V80015
REV D 022312
IDT5V80015
PLL CLOCK MULTIPLIER
CLOCK MULTIPLIER
DC Electrical Characteristics
VDD=1.8 V ±5%
,
VDDO = 3.3 V
,
Ambient temperature -40 to +85° C, unless stated otherwise
Parameter
Operating Voltage
Output Voltage
Input High Voltage
Input Low Voltage
Output High Voltage*
Output Low Voltage*
IDD Operating Supply Current
Input Capacitance
*Note: Guaranteed by design.
Symbol
VDD
VDDO
V
IH
V
IL
V
OH
V
OL
Conditions
Min.
1.71
3.135
0.65xVDD
-0.3
Typ.
1.8
3.3
Max.
1.89
3.465
V
DD
+ 0.3
0.35xVDD
0.4
Units
V
V
V
V
V
V
mA
pF
I
OH
= -2 mA
I
OL
= 2 mA
No load
VDD-0.45
20
4
AC Electrical Characteristics
VDD=1.8 V ±5%, VDDO = 3.3 V,
Ambient Temperature -40 to +85° C, unless stated otherwise
Parameter
Output Frequency
Frequency Synthesis Error
Output Clock Rise Time
Output Clock Fall Time
Output Clock Duty Cycle
Short Term Cycle-to-Cycle Jitter
Long Term Jitter
Aging
Power-up Time
Spread Spectrum Modulation Frequency
Note: Measured with a 7pF load.
Symbol
Conditions
Min.
-50
Typ.
Max.
50
Units
MHz
ppm
ns
ns
See Page 2
t
OR
t
OF
t
OD
t
ja
0.8 to 2.0 V
2.0 to 0.8 V
VDD/2
CLK output
CLK output
First year
1
1
45
50
75
55
100
TBD
5
10
32
45
%
ps
ps
ppm
ms
kHz
IDT®
PLL CLOCK MULTIPLIER
5
IDT5V80015
REV D 022312
京公网安备 11010802033920号
EEWORLD
