EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

50294-3045FB

Description
Board Connector, 135 Contact(s), 3 Row(s), Female, Right Angle, 0.1 inch Pitch, Solder Terminal, Locking, Receptacle,
CategoryThe connector    The connector   
File Size445KB,5 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Download Datasheet Parametric View All

50294-3045FB Overview

Board Connector, 135 Contact(s), 3 Row(s), Female, Right Angle, 0.1 inch Pitch, Solder Terminal, Locking, Receptacle,

50294-3045FB Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid2144530493
Reach Compliance Codecompliant
ECCN codeEAR99
YTEOL6.83
Board mount optionsHOLE .12
body width0.36 inch
subject depth0.72 inch
body length2.25 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationGOLD (50)
Contact completed and terminatedTin/Lead (Sn/Pb)
Contact point genderFEMALE
Contact materialBERYLLIUM COPPER
contact modeRECTANGULAR
Contact resistance20 mΩ
Contact styleSQ PIN-SKT
DIN complianceNO
Dielectric withstand voltage1000VDC V
Durability250 Cycles
Filter functionNO
IEC complianceNO
maximum insertion force0.97 N
Insulation resistance500000000 Ω
insulator materialGLASS FILLED POLYETHYLENE
JESD-609 codee0
MIL complianceNO
Plug contact pitch0.1 inch
Match contact row spacing0.1 inch
Mixed contactsNO
Installation option 1LOCKING
Installation methodRIGHT ANGLE
Number of connectorsONE
PCB row number3
Number of rows loaded3
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
OptionsGENERAL PURPOSE
PCB contact patternRECTANGULAR
PCB contact row spacing2.54 mm
Plating thickness50u inch
Rated current (signal)1 A
GuidelineUL
Terminal length0.145 inch
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts45
UL Flammability Code94V-0
Evacuation force-minimum value0.18 N
How to choose the installation height of Doppler flowmeter sensor?
When installing the Doppler flowmeter, the sensor should be installed as close to the bottom of the channel as possible. If there are a lot of sediments, silt, water plants or stones rolling on the bo...
ywj5188 Industrial Control Electronics
There is no signal at all when using the ceramic antenna on the cc2541. Can anyone help me see if that is wrong?
I tried to draw the board myself. The ceramic antenna I used was RFANT3216120A5T, and I drew it according to the data sheet. First, the balun outputted a 50Ω impedance, and then the antenna. But the r...
osiris00 RF/Wirelessly
Find an amplifier circuit
Find a differential amplifier circuit that amplifies a 1MHz signal by 10 times...
小朋友给我冲 Analog electronics
Interrupt-Based Ambient Light and Environment Sensor Node Reference Design for Sub-1 GHz Networks
The TI Design demonstrates a low-power approach to wireless environmental sensing that ensures up to 10 years of battery life.This design uses the Texas Instruments (TI) SimpleLink ultra-low-power Sub...
Jacktang RF/Wirelessly
STM32CUbe usage issues
I want to generate code using STM32Cube. Click Project, Settings, OK. Tip:Click Yes to download the firmware package, but an error occurs: Tip:It says that you can manually click the 'from local' butt...
chenbingjy stm32/stm8
The "analog electronics" version is difficult to enter
It takes an average of half a minute to display the list in the simulated electronic version, while other pages open in seconds....
PowerAnts Suggestions & Announcements

Technical ResourceMore

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号