Figure 7. Standard PECL Output Configuration Figure 8. Single Resistor Termination Scheme
Resistor values are typically 140 ohms for
3.3V operation.
Resistor values are typically 84 ohms for 2.5V
operation.
The VCC6 incorporates a standard PECL output scheme, which are un-terminated emitters as shown in Figure 7. There are numerous application notes on
terminating and interfacing PECL logic and the two most common methods are a single resistor to ground, Figure 8, and a pull-up/pull-down scheme as
shown in Figure 9. An AC coupling capacitor is optional, depending on the application and the input logic requirements of the next stage.
LVDS Application Diagrams
V
CC
LVDS
Driver
100
LVDS
Receiver
LVDS
Driver
100
Receiver
OUT+
OUT-
Figure 10 Standard LVDS
Output Configuration
Figure 11. LVDS to LVDS Connection, Internal 100ohm
Figure 12. LVDS to LVDS Connection
Some LVDS structures have an internal 100 ohm resistor on the
External 100ohm and AC blocking caps
input and do not need additional components.
Some input structures may not have an internal 100 ohm
resistor on the input and will need an external 100ohm
resistor for impedance matching. Also, the input may have
an internal DC bias which may not be compatible with
LVDS levels, AC blocking capacitors can be used.
One of the most important considerations is terminating the Output and Complementary Outputs equally. An unused output should not be left un-termi-
nated, and if one of the two outputs is left open it will result in excessive jitter on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to jitter related problems.
The tremendous growth of the wireless communications industry means that there has been an explosion in the testing of components and assemblies for wireless devices, including the testing of the vari...
Method 1:Use FLASH.cmd file to compile (such as: F28035.cmd). The program runs in FLASH. Double-click on the line number on the left side of the code to automatically generate a hardware breakpoint. T...
In PCB design, you need to draw pad files. Many people don't understand the two layers of Solder Mask Layers and Paste Mask layers. Here is a brief explanation. Solder mask: solder mask layer, also kn...
The outermost UUID is called service (serverID) for the time being, and the next layer is called characteristic (characteristicID) for the time being. The characteristic layer can be used to encapsula...
As an always-on communication method, Wi-Fi has been used in every corner of the world. The mainstream Wi-Fi 6, Wi-Fi 6E and the upcoming Wi-Fi 7 have achieved lower latency, higher data throughput an...
1. Classification of diodes
1. According to the semiconductor materials used, it can be divided into germanium diodes (Ge tubes) and silicon diodes (Si tubes).
2. According to their different...[Details]
Recently, foreign whistleblower Sudhanshu Ambhore obtained this relatively detailed internal document, which contains the core specifications of Qualcomm Snapdragon 735. The internal...[Details]
In single-chip C language programming, modular programming is very important. I think modularization just reflects the good portability of C language. In embedded programming, the hardware modules are...[Details]
Avnet, a technology solutions provider and component distributor, recently announced the acquisition of Witekio (formerly Adeneo Embedded). Witekio is a private company with expertise in software and...[Details]
LED signal light driver reference design
Abstract: This application note presents a reference design for a signal-lamp linear LED driver that consists of six strings of 4 LEDs per...[Details]
2022 will become the first year of lidar mass production, and many lidar companies have delivered good mass production answers. But no matter from the perspective of technology research and developme...[Details]
I feel like I have to tremble every day under the shadow of my job being "replaced" by robots . After the writing robot left, the reading and writing robot came. Recently, the intelligent reading a...[Details]
The structure of FIR filter is mainly non-recursive structure, without feedback from output to input. And FIR filter can easily obtain strict linear phase characteristics to avoid phase distortion of ...[Details]
South Korea's OLED panel exports to Japan reached $13.2 million in June, up 129.2% from the same period last year, reaching a monthly high, the Institute for Information and Communications Technology...[Details]
Acquisition adds advanced SmartNIC FPGA capabilities, accelerating time to market for Achronix customers’ networking applications Santa Clara, California, September 19, 2022 - Achronix Semiconduct...[Details]
The 2021 IAA Mobility, jointly organized by the German Association of the Automotive Industry (VDA) and the Munich Exhibition Group (Messe München), kicked off on September 7 and will last until Sept...[Details]
(1) Why choose AVR microcontroller? Flash program memory can be erased and written more than 1,000 times, and no scrapped products are produced. Some PICs are OTP and can only be burned once. AVR p...[Details]
On August 3, the Economic Information Daily, a media outlet affiliated with the central media, published an article titled "Spiritual Opium Has Become a Hundred-Billion-Dollar Industry". The first s...[Details]
In 2019, the overall server market growth momentum slowed down due to factors such as the global trade situation and the transfer of foundry production lines. However, since the second half of the ye...[Details]
Using precision current sources to provide constant current has been applied in many fields, including industrial process control, instrumentation, medical equipment and consumer electronics. For ...[Details]
Wireless Connectivity
京公网安备 11010802033920号
EEWORLD
