EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

HTS-119-G-C-2

Description
Board Connector, 19 Contact(s), 1 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Locking, Black Insulator, ROHS COMPLIANT
CategoryThe connector    The connector   
File Size1MB,1 Pages
ManufacturerSAMTEC
Websitehttp://www.samtec.com/
Environmental Compliance  
Download Datasheet Parametric View All

HTS-119-G-C-2 Overview

Board Connector, 19 Contact(s), 1 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Locking, Black Insulator, ROHS COMPLIANT

HTS-119-G-C-2 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerSAMTEC
package instructionROHS COMPLIANT
Reach Compliance Codecompliant
body width0.1 inch
body length1.9 inch
Connector typeBOARD CONNECTOR
Contact to complete cooperationGOLD (20) OVER NICKEL (50)
Contact completed and terminatedGold (Au) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialBRASS
contact modeRECTANGULAR
Contact styleRND PIN-SKT
DIN complianceNO
Filter functionNO
IEC complianceNO
Insulator colorBLACK
insulator materialLIQUID CRYSTAL POLYMER (LCP)
JESD-609 codee4
MIL complianceNO
Manufacturer's serial numberHTS
Plug contact pitch0.1 inch
Plug informationMULTIPLE MATING PARTS AVAILABLE
Mixed contactsNO
Installation option 1LOCKING
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number1
Number of rows loaded1
OptionsGENERAL PURPOSE
PCB contact patternRECTANGULAR
Plating thickness20u inch
polarization keyPOLARIZED HOUSING
GuidelineUL
reliabilityCOMMERCIAL
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts19
Base Number Matches1
Auto repair oscilloscope measuring the oxygen sensor signal of the car zirconium oxygen belt heater
Last time we talked about using an oscilloscope to measure the signal of the car's air flow meter. This time we will talk about using an oscilloscope to measure the car's oxygen sensor. The oxygen sen...
Micsig麦科信 Test/Measurement
Can the same-phase AC amplifier circuit be used for low frequencies?
[align=left][font=微软雅黑][size=12.0pt]The capacitor Ci next to R4 is equivalent to an open circuit for DC, so the DC component is not amplified; it is equivalent to a short circuit for AC, so the AC amp...
sfcsdc Analog electronics
Summary: Reading notes on "Operational Amplifier Parameter Analysis and LTspice Application Simulation"
Activity details: Read the good book "Operational Amplifier Parameter Analysis and LTspice Application Simulation" for free, take notes, and thoroughly master the knowledge of operational amplifiersSu...
okhxyyo Analog electronics
Equivalent transformation of passive three-terminal circuit
A circuit with three terminals and no internal power supply (independent source and controlled source) is called a passive three-terminal circuit. Figure 2-3-1 shows two passive three-terminal circuit...
fighting Analog electronics
How to use CPLD to collect asynchronous signals
Scenario: Use CPLD to decode a serial data channel. The data has no accompanying clock and has a fixed frequency but a different single-bit phase. My idea: I want to realize the acquisition of asynchr...
XCXBD EE_FPGA Learning Park
TLP3547 Evaluation Board Preliminary Evaluation Report
[align=center][color=#000000]Preliminary Evaluation Report on TLP3547 Evaluation Board[/color][/align][align=center][color=#000000] [/color][/align][align=center][color=#000000] Sichuan Institute of A...
wangdh45 Toshiba Photorelays TLP3547 Review

Technical ResourceMore

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号