ISOCOM
LTD
®
IECQ-CECC
COMPONENT
SPECIFICATION
QC 88000-C003
ISSUE 4
March 2007
Component Specification
For
Ceramic Hermetically Sealed
High Gain Optocouplers
Up-to-date lists and bibliographical references of IEQC-CECC publications may be downloaded from
www.iecq.org
Further copies of this document may be obtained from:
IEC
International Electrotechnical Commission
Commission Electrotechnique Internationale
Box 131, rue de Varembé, CH 1211 Geneva 20, Switzerland
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, Hutton Close, Crowther Industrial Estate, District 3, Washington, NE38 0AH
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 1 of 12
QC 88000-C001: 2007
ISOCOM
LTD
®
FOREWORD
The IECQ Quality Assessment System for Electronic Components (IECQ) is composed of those member countries of
the International Electrotechnical Commission (IEC) who wish to take part in a harmonized system for electronic
components of assessed quality. IECQ is also known in some European member countries as IECQ-CECC.
The object of the System is to facilitate international trade by the harmonization of the specifications and quality
assessment procedures for electronic components, and by the grant of an internationally recognised Mark, or
Certificate of Conformity. The components produced or services provided under the system are thereby acceptable in
all member countries without further testing.
This Component Specification is based upon the requirements of IEC Publication QC 001002-2, and has been
prepared by:
Isocom Ltd
Hutton Close
Crowther Industrial Estate
Washington
Tyne and Wear
NE38 0AH
Tel:
Fax:
+44 0191 4166 546
+44 0191 4155 055
and published under the authority of:
BSI Product Services
Maylands Avenue
Hemel Hempstead
Hertfordshire
HP2 4SQ
United Kingdom
AMENDMENT RECORD
Issue 1 – Changed Pages 4, 9 & 10 – Amendments 25/06/10
Issue 2 – Changed Pages 3, 4 & 5 – Amendments 05/07/10
Issue 3 – Changed Pages 3, 4, 5 & 6 – RoHS Compliant, Added CSM160/161/162-2 & Amendments 13/07/10
REQUIREMENTS
The requirements for IECQ-CECC Component Specifications as detailed in QC 001002-2 Amendment 1 clause 5.4 are
satisfied by the following data sheet.
It should note that IECQ-CECC are not responsible for manufacturers declarations made in data sheets which fall
outside the limits of approved detailed in IECQ-CECC certificates.
This Component Specification is intended for use with applicable IECQ-CECC Assessment Specifications. Eg: QC
88000-A0001
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, Hutton Close, Crowther Industrial Estate, District 3, Washington, NE38 0AH
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 2 of 12
QC 88000-C001: 2007
ISOCOM
LTD
®
Ceramic Hermetically Sealed High Gain Optocouplers
■
■
■
■
■
Features
▪
Release to IECQ-CECC
▪
Hermetically Sealed
▪
High Density Packaging
▪
1500V DC withstand Test Voltage
▪
Low Input Requirements: 0.5mA
▪
High Current Transfer Ratio: 1000% Typical
▪
RoHS Compliant
6N140A
CD750
CD5731
CH370
CS700
■
■
■
■
■
CS5700
CSM141/A
CSM160/161/162-2
CSM160/161/162-4
CSM1700
Applications
▪
Military, high reliability system
▪
Medical instruments
▪
Mos, Cmos Applications
▪
Logic Interfacing
▪
Data Transmission
▪
Transportation
Description
Each channel contains a light emitting diode which is optically coupled to an integrated high gain
photon detector. The high gain output stage features an open collector output providing both lower
saturation voltage and higher signalling speed than a conventional Photo-Darlington optocoupler.
The supply voltage can be operated as low as 2.0V without adversely affecting the parametric
performance. The High Current Transfer Ratio of the optocouplers makes them ideal for low input
current, min 0.5mA, applications.
The radiation immunity of the optocouplers compared to conventional photo transistor optocouplers
is due to the shallow depth and small junctions offered by the IC process.
The optocoupler family is also available in various package styles including 6, 8 and 16 pin DIP
through hole, 16 pin surface mount DIP flat pack and a 6 Pin leadless ceramic chip carrier. The
devices can be purchased with lead bend and plating options.
ISOCOM optocouplers are offered on the basis of similarity of emitter and detector therefore the
performance characterization is identical, subject to the limitations of the packages. The wafer die
similarities apply to the optocouplers for high reliability screening and radiation testing.
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, Hutton Close, Crowther Industrial Estate, District 3, Washington, NE38 0AH
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 3 of 12
QC 88000-C001: 2007
ISOCOM
LTD
®
Selection Guide Package Styles and Configuration Options
Package
5 pin
Hybrid
6 Pad LCC
1
8 pin DIP
1
8 pin DIP
2
16 pin DIP
4
16 pin
Flat Pack
2/4
Lead Style
1
Channels
Common Channel Wiring
Isocom Part Numbers and Options
Commercial
Defense Level
Space Level
Standard Gold Plate Finish
Solder Dipped
Butt Cut/Gold Plate
Gull Wing/Soldered
Crew Cut/Gold Plate
CH370
CH370/L2
CH370/L2S
CSM141A
CSM1700
CSM141A/L2
CSM1700/L2
CSM141A/L2S
CSM1700/L2S
Gold Plate
CS5700
CS700
CS5700/L2
CS700/L2
CS5700/L2S
CS700/L2S
Gold Plate
Option 20
Option 10
Option 30
Option 60
CD750
CD5731
CD750/L2
CD5731/L2
CD750/L2S
CD5731/L2S
Gold Plate
Option 20
Option 10
Option 30
Option 60
6N140A
6N140A/L2
6N140A/L2S
Gold Plate
Option 20
Option 10
Option 30
Option 60
CSM160/161/
162
CSM160/161/
162/L2
CSM160/161/
162/L2S
Gold Plate
Functional Diagrams
CH370
5 pin Hybrid
1 Channel
CSM141A
6 Pad LCC
1 Channel
CS5700
CS700
8 pin DIP
1 Channel
CD750
CD5731
8 pin DIP
2 Channel
6N140A
16 pin DIP
4 Channel
CSM160/161
/162-2
16 pin Flat Pack
2 Channel
6
1
2
5
4
3
CSM1700
6 Pad LCC
1 Channel
CSM160/161
/162-4
16 pin Flat Pack
4 Channel
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, Hutton Close, Crowther Industrial Estate, District 3, Washington, NE38 0AH
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 4 of 12
QC 88000-C001: 2007
ISOCOM
LTD
®
Outline Drawings
16 pin DIP, 4 Channel
16 pin Flat Pack, 2 and 4 Channel
NOTE: DIMENSIONS IN MILLIMETERS
8 pin DIP 1 and 2 Channel
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, Hutton Close, Crowther Industrial Estate, District 3, Washington, NE38 0AH
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 5 of 12
QC 88000-C001: 2007
京公网安备 11010802033920号
EEWORLD
