EEWORLDEEWORLDEEWORLD

Part Number

Search

SP-200.12OHM5%LF

Description
Fixed Resistor, Wire Wound, 1W, 0.12ohm, 5% +/-Tol, 800ppm/Cel, Through Hole Mount, AXIAL LEADED, ROHS COMPLIANT
CategoryPassive components    The resistor   
File Size224KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Environmental Compliance  
Download Datasheet Parametric View All

SP-200.12OHM5%LF Overview

Fixed Resistor, Wire Wound, 1W, 0.12ohm, 5% +/-Tol, 800ppm/Cel, Through Hole Mount, AXIAL LEADED, ROHS COMPLIANT

SP-200.12OHM5%LF Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
package instruction,
Reach Compliance Codecompliant
ECCN codeEAR99
JESD-609 codee3
Installation featuresTHROUGH HOLE MOUNT
Number of terminals2
Maximum operating temperature160 °C
Package shapeTUBULAR PACKAGE
Rated power dissipation(P)1 W
Rated temperature50 °C
resistance0.12 Ω
Resistor typeFIXED RESISTOR
surface mountNO
technologyWIRE WOUND
Temperature Coefficient800 ppm/°C
Terminal surfaceMatte Tin (Sn)
Terminal shapeWIRE
Tolerance5%
Base Number Matches1
General Purpose Failsafe
Molded Wirewound Resistor
SP20/SP20F Series
SP20F Fusible
±5%, ±10% tolerance
0.1 ohm to 1200 ohms
F version has flame resistant coating
1 watt rated with 1/2 watt dimensions
Drop-in replacement for BW20/BW20F
Weldable and solderable magnetic lead
TCR’s as low as ±150 ppm/°C standard (custom TC’s available)
Lead free, RoHS compliant construction available
3
1
4
2
(See notes below)
Electrical Data
IRC Type
SP20
SP20F
1. Resistive Element
All resistor types have resistance alloy
winding on a braided fiberglass substrate.
Intermediate silicone coatings are used
to enhance processibility and to provide
protection to the resistive element.
2. Termination
The SP-20 and SP-20F resistors are
terminated using an alloy coated copper
flashed steel lead welded to a cap of the
same material. This termination assembly is
mechanically crimped, utilizing an improved
crimp design, to the resistive element.
3. Encapsulation
The SP-20 and the SP20F are encapsulated
utilizing a compression molded phenolic
plastic material. The SP-20F has a flame
resistance coating applied over the resistive
element to provide flammability protection
when destructive overloads may occur.
4. Marking
All products are marked utilizing heat and
solvent resistant color code bands consistent
with EIA/MIL requirements. The first band
is double width to designate wirewound
construction. A fifth band, blue in color, is
used for flameproof identification.
EIA RS-344 Style
MIL-R-11 Style
Resistance - Std.
Tolerance - Std.
CRU1
RC20/RC32
0.1Ω to 1200Ω
±5%, ±10%
CRU1
RC20/RC32
0.1Ω to 1000Ω
±5%, ±10%
Power Rating
1 watt @ 50°C
1 watt @ 50°C
3/4 watt @ 70°C
3/4 watt @ 70°C
---
1/2 watt @ 100°C
Derating to 0 @ 160°C Derating to 0 @ 160°C
Max. Continuous Working Voltage
Min. Insulation
Resistance
Min. Dielectric
Withstanding Volts
(RMS)
Reduced Pressure
Dry
Wet
ATM
PR
10,000 Meg
100 Meg
700V
450V
120°C @ 1 watts
5%
Negligible
PR
10,000 Meg
100 Meg
700V
450V
120°C @ 1 watts
5%
Negligible
Hotspot Temperature Rise
Typical Load Life
Current Noise
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
Wire and Film Technologies Division
• 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
SP20/SP20F Series Issue December 2008 Sheet 1 of 3
What are the essential technologies for 5G smartphones?
The introduction of new 5G frequency bands means more antennas must be packed into less space. The number of antennas will increase from 4 to 6 in a typical LTE phone today to 6 to 10 in a 5G smartpho...
alan000345 RF/Wirelessly
【Want Talent】Beijing-3 embedded positions
1 Embedded ARM 1.1 Job ResponsibilitiesResponsible for embedded product software requirements analysis, architecture design, and solution output; Responsible for the design, debugging, upgrade and opt...
Coen0518 Recruitment
EEWORLD University Hall----Introduction to Digital Power Supply
Introduction to Digital Power Supply : https://training.eeworld.com.cn/course/4942...
wanglan123 Analog electronics
SPI interrupt and Main usage issues
I would like to ask, if the SPI Write function is permanently used in main, and the interrupt also has the SPI Write function, if Main and the interrupt are reused to SPI Write, what will happen to SP...
news9801 stm32/stm8
Analysis Example: A Zener Diode Regulator Circuit
OBJECTIVEA regulator is a circuit that maintains a constant output voltage across a load regardless of load current. For example, the load could be a microcontroller system that requires the supply vo...
Jacktang Analogue and Mixed Signal
Comparison of CC2540 and nRF51822 application development
[size=4] I looked at the application development in the nRF51822 SDK, and it is quite different from TI. [/size] [size=4] The development framework of TI CC2540 is quite complete, and this software fr...
Aguilera Wireless Connectivity

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号