H HiTRON
PCB-MOUNT DC-DC CONVERTER ENCAPSULATED MODULES
30 WATTS SINGLE OUTPUT HDM30-S SERIES
FEATURES:
SINGLE OUTPUT
WIDE 4:1 & 2:1 INPUT RANGE
30W ISOLATED OUTPUT
SIX-SIDED SHIELD
SPECIFICATION
INPUT SPECIFICATION
Input Range:
Wide 4:1 & 2:1 DC input range.
See Ratings Chart.
Input Voltage:
Nominal 12/24/48Vdc.
Input Current:
Various with input range and load.
See Ratings Chart.
Input Fuse:
Use external fuse.
Input Filter:
Pi-Network.
Overvoltage Shutdown:
Optional. Factory set.
Undervoltage Shutdown:
8Vdc.
Isolation Resistor:
1,000 Mega Ohms.
Isolation Voltage:
1,500Vdc.
EMI:
Six-sided metal shielding.
Remote On/Off:
TTL/CMOS-Compatible Input Control.
(Voltage refer to the –Input)
Positive Logic
version for Standard set up:
ON(Enable)=Open(or
2.5-5.0Vdc above-Vin).
OFF(Disable)=Short(or
0-0.8Vdc above-Vin).
Negative Logic
version option available by adding a
“N”
suffix to the end of Model #.
OUTPUT SPECIFICATION
Output Voltage:
See Ratings Chart.
Output Current:
See Ratings Chart.
Voltage Accuracy:
Main O/P ±2.0% typical.
Line Regulation:
Various with input & output voltages.
±0.5% typical.
Load Regulation:
Various with output voltages.
±1.0% typical.
Noise & Ripple:
Typical 100mV for 3.3V/5.0V &
1.0% for others peak to peak.
OVP:
Built-in on main output.
Overload Protection (OLP):
Fully protected against output overload and short circuit.
OLP set at about 125-150% rating output wattage.
Consult the factory for OLP setting.
Operating Temperature:
-10 to +70°C range.
0°C to +60°C full load without derating.
From +60°C, derating linearly to half load @+70°C.
(Refer to Derating Chart.)
GENERAL SPECIFICATION
Efficiency:
81% typical various with input.
Switching Frequency:
Fixed frequency 100K Hz.
Circuit Topology:
Forward Circuit.
Transient Response:
Peak deviation 200mV,
Recovery time < 3mSec.@ 25% step load change.
Case:
Black coated copper with non-conductive
metal base.
Power Density:
10 Watts. / Cubic inch.
MTBF:
Type 1,000,000 hours to Mil. Std.217, 25°C.
Temperature:
-20°C to +85°C.
Temperature Coefficient:
0.02% /°C.
Cooling:
Convection cooling up to +60°C @ full load.
At least 100LFM moving air is recommended for
full load > +60°C in a confined area.
Humidity:
Up to 95%RH, Non-condensing.
Commercial Grade only.
NOTE:
(1) All measurements are at nominal input, full load, and +25°C unless otherwise specified.
(2) Line Regulation measured from High to Low Lines at full load.
(3) Load Regulation measured from Full Load to 1/2 Full Load at nominal input.
(4) Correct fuse size by calculating the max. DC current drain at low Line input & Load and then adding 20-25％for the desired fuse size.
Due to requests in market and advances in technology, specifications subject to change without notice.
-27-
INPUT/OUTPUT & VOLTAGE/CURRENT RATINGS CHART
SINGLE OUTPUT
MODEL NO.
INPUT
Vdc
INPUT CURRENT
N. L.
(mA)
F.L.
2300
2700
2650
2750
2800
3100
1150
1350
1325
1375
1400
1550
575
675
662
687
700
775
1175
1375
1350
1400
1425
1575
587
687
675
700
712
787
OUTPUT
VO1(Vdc)
@★
3.3V
5.0V
9.0V
12.0V
15.0V
24.0V
3.3V
5.0V
9.0V
12.0V
15.0V
24.0V
3.3V
5.0V
9.0V
12.0V
15.0V
24.0V
3.3V
5.0V
9.0V
12.0V
15.0V
24.0V
3.3V
5.0V
9.0V
12.0V
15.0V
24.0V
OUTPUT
VO1(A)
6.40A
5.00A
2.80A
2.20A
1.80A
1.25A
6.40A
5.00A
2.80A
2.20A
1.80A
1.25A
6.40A
5.00A
2.80A
2.20A
1.80A
1.25A
6.40A
5.00A
2.80A
2.20A
1.80A
1.25A
6.40A
5.00A
2.80A
2.20A
1.80A
1.25A
CASE
SIZE
DM2A
DM2A
DM2A
DM2A
DM2A
DM2A
DM2A
DM2A
DM2A
DM2A
DM2A
DM2A
DM2A
DM2A
DM2A
DM2A
DM2A
DM2A
DM2A
DM2A
DM2A
DM2A
DM2A
DM2A
DM2A
DM2A
DM2A
DM2A
DM2A
DM2A
HDM30-12B-S03
9.0-
HDM30-12B-S05
9.0-
HDM30-12B-S09
9.0-
HDM30-12B-S12
9.0-
HDM30-12B-S15
9.0-
HDM30-12B-S24
9.0-
HDM30-24B-S03
18.0-
HDM30-24B-S05
18.0-
HDM30-24B-S09
18.0-
HDM30-24B-S12
18.0-
HDM30-24B-S15
18.0-
HDM30-24B-S24
18.0-
HDM30-48B-S03
36.0-
HDM30-48B-S05
36.0-
HDM30-48B-S09
36.0-
HDM30-48B-S12
36.0-
HDM30-48B-S15
36.0-
HDM30-48B-S24
36.0-
HDM30-24D-S03
9.0-
HDM30-24D-S05
9.0-
HDM30-24D-S09
9.0-
HDM30-24D-S12
9.0-
HDM30-24D-S15
9.0-
HDM30-24D-S24
9.0-
HDM30-48D-S03
20.0-
HDM30-48D-S05
20.0-
HDM30-48D-S09
20.0-
HDM30-48D-S12
20.0-
HDM30-48D-S15
20.0-
HDM30-48D-S24
20.0-
Symbols:
"★" OVP built-in.
30
18.0
30
18.0
30
18.0
30
18.0
30
18.0
30
18.0
20
36.0
20
36.0
20
36.0
20
36.0
20
36.0
20
36.0
15
72.0
15
72.0
15
72.0
15
72.0
15
72.0
15
72.0
30
36.0
30
36.0
30
36.0
30
36.0
30
36.0
30
36.0
20
72.0
20
72.0
20
72.0
20
72.0
20
72.0
20
72.0
"@" Adjustable.
MECHANICAL DIMENSIONS:
MM [INCHES]
PIN NO.
PIN #1.
PIN #2.
PIN #3.
PIN #4.
PIN #5.
PIN #6.
PIN #7.
PIN #8.
PIN #9.
PIN #10.
WEIGHT:
156.0g (5.6 Oz.)
PIN ASSIGNMENT
SINGLE
Remote ON/OFF
+INPUT
-INPUT/-Vin
NO PIN
NO PIN
OUTPUT TRIM
NO PIN
+VO1
DC-COM
NO PIN
DERATING CHART
CASE SIZE: DM2A
-28-
H HiTRON
PCB-MOUNT DC-DC CONVERTER ENCAPSULATED MODULES
30 WATTS DUAL OUTPUT HDM30-D SERIES
FEATURES:
DUAL OUTPUT
WIDE 4:1 & 2:1 INPUT RANGE
30W ISOLATED OUTPUT
SIX-SIDED METAL SHIELD
SPECIFICATION
INPUT SPECIFICATION
Input Range:
Wide 4:1 & 2:1 DC input range.
See Ratings Chart.
Input Voltage:
Nominal 12/24/48Vdc.
Input Current:
Various with input range and load.
See Ratings Chart.
Input Fuse:
Use external fuse.
Input Filter:
Pi-Network.
Overvoltage Shutdown:
Optional. Factory set.
Undervoltage Shutdown:
8Vdc.
Isolation Resistor:
1,000 Mega Ohms.
Isolation Voltage:
1,500Vdc.
EMI:
Six-sided metal shielding.
Remote On/Off:
TTL/CMOS-Compatible Input Control.
(Voltage refer to the -Input).
Positive Logic
version for Standard set up:
ON(Enable)=Open(or
2.5-5.0Vdc above-Vin).
OFF(Disable)=Short(or
0-0.8Vdc above-Vin).
Negative Logic
version option available by adding a
“N”
suffix to the end of Model #.
Remark: Logic voltage refer to –Input (-Vin)
OUTPUT SPECIFICATION
Output Voltage:
See Ratings Chart.
Output Current:
See Ratings Chart.
Voltage Accuracy:
Main O/P ±2.0% typical.
Line Regulation:
Various with input voltages.
±0.5% typical.
Load Regulation:
Various with output voltages.
VO1 ±1.0% typical.
VO2 ±2.0% typical.
Noise & Ripple:
100mV for 3.3V/5.0V & 1.0% typical
for other output peak to peak.
OVP:
Built-in on main output.
Adjustability:
VO1 O/P may optionally be external
trimmed ±3.0% with a fixed resistors or trim-pot.
Overload Protection (OLP):
Fully protected against output overload and short circuit.
OLP set at about 125-150% rating output wattage.
Consult the factory for OLP setting.
GENERAL SPECIFICATION
Efficiency:
76- 81% typical, various with input &
output voltage.
Switching Frequency:
Fixed frequency 100K Hz.
Circuit Topology:
100K Hz. Forward Circuit.
Transient Response:
Peak deviation 200mV,
Recovery time < 3mSec. @ 25% step load change.
Case:
Black coated copper with non-conductive metal base.
Power Density:
10.0 Watts. / Cubic inch.
MTBF:
1,000,000 hours to Mil. Std. 271, 25°C.
Operating Temperature:
-10°C to +70°C range.
0°C to +60°C @ full load without derating.
From +60°C, derating linearly to half load@+70°C.
(Refer to the Derating Chart).
Temperature:
-20°C to +85°C.
Temperature Coefficient:
± 0.03% /°C.
Cooling:
Convection cooling up to +60°C @ full load.
At least 100LFM moving air is recommended
for F-L > +60°C in a confined area.
Humidity:
Up to 95%RH, Non-condensing.
Commercial Grade only.
NOTE:
(1) All measurements are at nominal input, full load, and +25°C unless otherwise specified.
(2) Line Regulation measured from High to Low Lines at full load.
(3) Load Regulation measured from Full Load to 1/2 Full Load at nominal input.
(4) Correct fuse size by calculating the max. DC current drains at low Line input & Load and then adding 20-25% for the desired fuse size.
Due to requests in market and advances in technology, specifications subject to change without notice.
-29-
INPUT/OUTPUT & VOLTAGE/CURRENT RATINGS CHART
DUAL OUTPUT
MODEL NO.
HDM30-12B-D05
HDM30-12B-D12
HDM30-12B-D15
HDM30-24B-D05
HDM30-24B-D12
HDM30-24B-D15
HDM30-48B-D05
HDM30-48B-D12
HDM30-48B-D15
HDM30-24D-D05
HDM30-24D-D12
HDM30-24D-D15
HDM30-48D-D05
HDM30-48D-D12
HDM30-48D-D15
INPUT
Vdc
9.0- 18.0
9.0- 18.0
9.0- 18.0
18.0- 36.0
18.0- 36.0
18.0- 36.0
36.0- 72.0
36.0- 72.0
36.0- 72.0
9.0- 36.0
9.0- 36.0
9.0- 36.0
20.0- 72.0
20.0- 72.0
20.0- 72.0
INPUT CURRENT
OUTPUT (Vdc)
-VO2‖
N.L.
(mA)
F.L.
+VO1@★
30
2,670
+5.0V
-5.0V
30
2,500
+12.0V
-12.0V
30
2,590
+15.0V
-15.0V
20
1,560
+5.0V
-5.0V
20
1,525
+12.0V
-12.0V
20
1,525
+15.0V
-15.0V
20
780
+5.0V
-5.0V
20
763
+12.0V
-12.0V
20
763
+15.0V
-15.0V
40
1,350
+ 5.0V
- 5.0V
40
1,265
+12.0V
-12.0V
40
1,310
+15.0V
-15.0V
30
800
+5.0V
-5.0V
30
775
+12.0V
-12.0V
30
775
+15.0V
-15.0V
"‖" Double Feedback.
OUTPUT (A)
+VO1
-VO2
2.50A
2.50A
1.00A
1.00A
0.83A
0.83A
3.00A
3.00A
1.25A
1.25A
1.00A
1.00A
3.00A
3.00A
1.25A
1.25A
1.00A
1.00A
2.50A
2.50A
1.00A
1.00A
0.83A
0.83A
3.00A
3.00A
1.25A
1.25A
1.00A
1.00A
CASE
SIZE
DM2A
DM2A
DM2A
DM2A
DM2A
DM2A
DM2A
DM2A
DM2A
DM2A
DM2A
DM2A
DM2A
DM2A
DM2A
Symbols:
"★" OVP built-in.
"@" Adjustable.
MECHANICAL DIMENSIONS:
MM [INCHES]
WEIGHT:
156.0g (5.6 Oz.)
PIN ASSIGNMENT
PIN NO.
PIN# 1.
PIN# 2.
PIN# 3.
PIN# 4.
PIN# 5.
PIN# 6.
PIN# 7.
PIN# 8.
PIN# 9.
PIN# 10.
DUAL
Remote ON/OFF
+ INPUT
-INPUT/-Vin
NO PIN
+VO1
DC-COM
-VO2
OUTPUT TRIM
NO PIN
NO PIN
DERATING CHART
CASE SIZE: DM2A
-30-
H HiTRON
PCB-MOUNT DC-DC CONVERTER ENCAPSULATED MODULES
30 WATTS TRIPLE OUTPUT HDM30-T SERIES
FEATURES:
TRIPLE OUTPUT
WIDE 4:1 & 2:1 INPUT RANGE
30W ISOLATED OUTPUT
SIX-SIDED METAL SHIELD
SPECIFICATION
INPUT SPECIFICATION
Input Range:
Wide 4:1 & 2:1 DC input range.
See Ratings Chart.
Input Voltage:
Nominal 12/24/48Vdc.
Input Current:
Various with input range and load.
See Ratings Chart.
Input Fuse:
Use external fuse.
Input Filter:
Pi-Network.
Overvoltage Shutdown:
Optional. Factory set.
Undervoltage Shutdown:
8Vdc.
Isolation Resistor:
1,000 Mega Ohms.
Isolation Voltage:
1,500Vdc.
EMI:
Six-sided metal shielding.
Remote On/Off:
TTL/CMOS-Compatible Input Control.
Positive Logic
version for Standard set up:
ON(Enable)=Open(or
2.5-5.0Vdc above-Vin)
OFF(Disable)=Short(or
0-0.8Vdc above-Vin)
Negative Logic
version option available by adding a
“N”
suffix to the end of Model #.
Remark: [Voltage refer to –Input (-Vin)].
OUTPUT SPECIFICATION
Output Voltage:
See Ratings Chart.
Output Current:
See Ratings Chart.
Voltage Accuracy:
Main O/P ±2.0% typical.
Line Regulation:
Various with input voltages. ±0.5% typ.
Load Regulation:
Various with output voltages.
VO1 & VO3 ±2.0% typical.
VO2 ±5.0% typical.
Noise & Ripple:
100mV for 3.3V/5.0V & 1.0% typical
for other output peak to peak.
OVP:
Built-in on main output.
Adjustability:
VO1 O/P may optionally be external
trimmed ±3.0% with a fixed resistors or trim-pot.
Overload Protection (OLP):
Fully protected against output overload and short circuit.
OLP set at about 125-150% rating output wattage.
Consult the factory for OLP setting.
GENERAL SPECIFICATION
Efficiency:
78-81% typical, various with input &
output voltage.
Switching Frequency:
Fixed frequency 100K Hz.
Circuit Topology:
100K Hz. Forward Circuit.
Transient Response:
Peak deviation 200mV,
Recovery time < 3mSec. @ 25% step load change.
Case:
Black coated copper with non-conductive metal base.
Power Density:
10.0 Watts. / Cubic inch.
MTBF:
1,000,000 hours Mil.Std.271, 25°C.
Operating Temperature:
-10°C to +70°C range.
0°C to +60°C @ full load without derating.
From+60°C derating linearly to half load@+70°C.
(Refer to the Derating Chart).
Storage Temperature:
-20 to +85°C.
Temperature Coefficient:
± 0.03% /°C.
Cooling:
Convection cooling up to +60°C @ full load.
At least 100LFM moving air is recommended for full
load > +60°C in a confined area.
Humidity:
Up to 95%RH, Non-condensing.
Commercial Grade only.
NOTE:
(1) All measurements are at nominal input, full load, and +25°C unless otherwise specified.
(2) Line Regulation measured from High to Low Lines at full load.
(3) Load Regulation measured from Full Load to 1/2 Full Load at nominal input.
(4) Correct fuse size by calculating the max. DC current drains at low Line input & Load and then adding 20-25% for the desired fuse size.
Due to requests in market and advances in technology, specifications subject to change without notice.
-31-
Domestic Chip Exchange
京公网安备 11010802033920号
EEWORLD
