LTS5.5MCB datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Analog mixed-signal IC> filter> LTS5.5MCB

LTS5.5MCB: DescriptionCeramic BPF, 5.5MHz, ROHS AND REACH COMPLIANT, CERAMIC PACKAGE-3; CategoryAnalog mixed-signal IC filter; File Size233KB，1 Pages; ManufacturerEuroquartz; Websitehttp://www.euroquartz.co.uk/; Environmental Compliance

Download Datasheet Parametric Compare View All

LTS5.5MCB Overview

Ceramic BPF, 5.5MHz, ROHS AND REACH COMPLIANT, CERAMIC PACKAGE-3

LTS5.5MCB Parametric

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
Reach Compliance Code	compliant
Center frequency or cutoff frequency (fo/fc)	5.5 MHz
filter type	CERAMIC BPF
high	7 mm
Input/output impedance	470 OHM
Maximum insertion loss	6 dB
length	9 mm
Installation type	THROUGH HOLE MOUNT
physical size	L9.0XB4.0XH7.0 (mm)/L0.354XB0.157XH0.276 (inch)
width	4 mm
Base Number Matches	1

Preview

Download Datasheet

View All

EURO

QUARTZ

CERAMIC FILTER LTS_MCB

Ceramic discriminators for AM applications:

SMD type for reflow soldering (JTBC)

AUDIO IF APPLICATIONS

Leaded type (JTBM)

PHYSICAL CHARACTERISTICS

Random Drop Test:

Filter performance shall be tested after

3 x random drop from 1.0metre onto

concrete floor. No visible damage

should be observed and the measured

values shall be within specification.

Filte shall be measure after being

applied with vibration, amplitude

1.5mm, frequency 10Hz to 55Hz for 2

hours in each of the 3 perpendicular

planes. The measured electrical values

shall be within specification.

Lead terminals are immersed up to

2.0mm from the filter body in a solder

bath (350° ±10°C for 5±0.5 seconds).

The filter should be measured after

being in room temperature for 1 hour.

Lead terminals are immersed in resin

for 5 seconds then immersed in a

soldering bath at 250°C±5°C for 3

seconds ±0.5 seconds. A minimum of

95% of lead terminals surface shall be

covered with solder.

Vibration:

Resistance to Solder Heat:

ELECTRICAL SPECIFICATION

Nominal Frequency:

3dB Bandwidth:

Insertion Loss:

20dB Bandwidth:

Spurious Loss 0~6.5MHz:

Rated Voltage:

Insulation Resistance:

Temperature Characteristics

(-25° to +85°C):

Storage Temperature:

Input/Output Impedance:

4.5, 5.5, 6.0 or 6.50MHz

±70kHz min.

6.0dB max.

350kHz max.

30dB min.

DC 50V (I minute)

100MΩ min.

±100ppm/°C max.

-40°C to +85°C

470Ω

Solderability:

ENVIRONMENTAL SPECIFICATION

High Temperature:

After being placed in a chamber at

+85°±2°C for 96 hours and left for one

hour at room temperature the

measured values are to be within

specification.

After being placed in a chamber at

-25°±2°C for 96 hours and left for one

hour at room temperature the

measured values are to be within

specification.

After being placed in a chamber with a

humidity of 90~95% RH and a

temperature of +40° for 96 hours and

left for one hour at room temperature

the measured values are to be within

specification.

After being kept at room temperature

the filter shall be placed at a

temperature of -25°C. After 30 minutes

at the temperature the filter is

immediately placed at a temperature of

+85°C. After 30 minutes the filter is

again placed at a temperature of -25°C.

This is one cycle. The filter is subjected

to 5 cycles. After one hour at room

temperature the measured values are to

be within specification.

TEST CIRCUIT

Low Temperature:

Humidity:

4.5MHz

5.5MHz

6.0MHz

6.5MHz

PART NUMBERS

Frequency

4.5MHz

5.0MHz

6.0MHz

6.5MHz

Part Number

LTS4.5MCB

LTS5.5MCB

LTS6.0MCB

LTS6.5MCB

1kΩ

600Ω

470Ω

Heat Shock:

EUROQUARTZ LIMITED Blacknell Lane CREWKERNE Somerset UK TA18 7HE

Tel: +44 (0)1460 230000 Fax: +44 (0)1460 230001 info@euroquartz.co.uk www.euroquartz.co.uk

LTS5.5MCB Related Products

	LTS5.5MCB	LTS4.5MCB	LTS6.0MCB	LTS6.5MCB
Description	Ceramic BPF, 5.5MHz, ROHS AND REACH COMPLIANT, CERAMIC PACKAGE-3	Ceramic BPF, 4.5MHz, ROHS AND REACH COMPLIANT, CERAMIC PACKAGE-3	Ceramic BPF, 6MHz, ROHS AND REACH COMPLIANT, CERAMIC PACKAGE-3	Ceramic BPF, 6.5MHz, ROHS AND REACH COMPLIANT, CERAMIC PACKAGE-3
Is it lead-free?	Lead free	Lead free	Lead free	Lead free
Is it Rohs certified?	conform to	conform to	conform to	conform to
Reach Compliance Code	compliant	compliant	compliant	compliant
Center frequency or cutoff frequency (fo/fc)	5.5 MHz	4.5 MHz	6 MHz	6.5 MHz
filter type	CERAMIC BPF	CERAMIC BPF	CERAMIC BPF	CERAMIC BPF
high	7 mm	7 mm	7 mm	7 mm
Input/output impedance	470 OHM	470 OHM	470 OHM	470 OHM
Maximum insertion loss	6 dB	6 dB	6 dB	6 dB
length	9 mm	9 mm	9 mm	9 mm
Installation type	THROUGH HOLE MOUNT	THROUGH HOLE MOUNT	THROUGH HOLE MOUNT	THROUGH HOLE MOUNT
physical size	L9.0XB4.0XH7.0 (mm)/L0.354XB0.157XH0.276 (inch)	L9.0XB4.0XH7.0 (mm)/L0.354XB0.157XH0.276 (inch)	L9.0XB4.0XH7.0 (mm)/L0.354XB0.157XH0.276 (inch)	L9.0XB4.0XH7.0 (mm)/L0.354XB0.157XH0.276 (inch)
width	4 mm	4 mm	4 mm	4 mm
Base Number Matches	1	1	1	1

Recommended Resources

KJZ6 type three-phase fully controlled bridge trigger control circuit

Gated light circuit

Using 5G14 switching regulated power supply

Circuit with multiple op amps connected in parallel

Bistable switch control circuit composed of T996/998C

Rice cooker circuit diagram 01

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components