REVISION N
VERTICAL
(HQDP-040-XX.XX-STR-STR-1 SHOWN)
FIG. 1
HQDP-XXX-XX.XX-XXX-XXX-X-X
No OF POSITIONS
-020, -040, -060, -080
(PER ROW)
LENGTH
-XX.XX (INCHES)
(3.75[95.3] MIN)
(SEE NOTE 2)
(SEE NOTE 8)
FIRST END
-TTR: TERMINAL, TOP, RIGHT
-TTL: TERMINAL, TOP, LEFT
-TBR: TERMINAL, BOTTOM, RIGHT
-TBL: TERMINAL, BOTTOM, LEFT
-STR: SOCKET, TOP, RIGHT
-STL: SOCKET, TOP, LEFT
-SBR: SOCKET, BOTTOM, RIGHT
-SBL: SOCKET, BOTTOM, LEFT
(SEE TABLE 1 & SHEET 2)
-TEU: TERMINAL, EDGE MOUNT, UP
-TED: TERMINAL, EDGE MOUNT, DOWN
-SEU: SOCKET, EDGE MOUNT, UP
-SED: SOCKET, EDGE MOUNT, DOWN
(SEE TABLE 5 & SHEET 4)
END OPTION
-F: SCREW OPTION FIRST END ONLY
-S: SCREW OPTION SECOND END ONLY
-B: SCREW OPTION BOTH ENDS
-L: FIRST END RT1 OPTION (SEE FIG. 6, SHT 6)
(SEE NOTE 9 & 10)
-R: SECOND END RT1 OPTION (SEE FIG. 6, SHT 6)
(SEE NOTE 9 & 10)
-D: BOTH ENDS RT1 OPTION (SEE FIG. 6, SHT 6)
N
(SEE NOTE 9 & 10)
-1: FIRST SCREW OPTION,
SECOND END RT1 OPTION (SEE FIG. 6, SHT 6)
(SEE NOTE 9 & 10)
-2: FIRST END RT1 OPTION,
SECOND END SCREW OPTION (SEE FIG. 6, SHT 6)
(SEE NOTE 9 & 10)
-N: NO CAPS
(SEE FIG. 3, SHEET 5 FOR EDGE MOUNT
END OPTIONS)
(SEE FIG. 4, SHEET 5 FOR DOUBLE
VERTICAL END OPTIONS)
(SEE FIG. 5, SHEET 5 FOR NO CAPS OPTIONS)
(LEAVE BLANK FOR STANDARD CAPS
BOTH ENDS)
WIRING OPTION
SECOND END
-1: PIN 1 TO PIN 1
-TTR: TERMINAL, TOP, RIGHT
-2: PIN 1 TO PIN 2
-TTL: TERMINAL, TOP, LEFT
-3: PIN 1 TO PIN N-1
-TBR: TERMINAL, BOTTOM, RIGHT
-4: PIN 1 TO PIN N
-TBL: TERMINAL, BOTTOM, LEFT
(SEE TABLE 9, SHEET 7)
-STR: SOCKET, TOP, RIGHT
-STL: SOCKET, TOP, LEFT
-SBR: SOCKET, BOTTOM, RIGHT
-SBL: SOCKET, BOTTOM, LEFT
(SEE TABLE 1 & SHEET 3)
-TEU: TERMINAL, EDGE MOUNT, UP
-TED: TERMINAL, EDGE MOUNT, DOWN
-SEU: SOCKET, EDGE MOUNT, UP
-SED: SOCKET, EDGE MOUNT, DOWN
(SEE TABLE 5 & SHEET 4)
LENGTH: XX.XX + "L" REF (SEE TABLE 4)
SUB-HQDP-X-
XXX-XX-XX
LENGTH: XX.XX
02
01
"A" REF
(TYP)
01%
01
02
C1
'A'
"B" REF
(TYP)
DO NOT
SCALE FROM
THIS PRINT
N
(SEE TABLE 3)
N-1
(SEE TABLE 3)
SUB-HQDP-X-XXX-XX-XX
N
(SEE TABLE 3)
N-1
(SEE TABLE 3)
.875 22.23 REF (TYP)
.665 16.89 REF (TYP)
.248 6.30 REF (TYP)
STS-01
(TIGHTEN TO 1.4 - 1.7 IN-LBS)
(4 PLCS)
HQDP-XX-01
HDRL-11
(SEE NOTE 5)
FIRST END
SECOND END
NOTES:
1.
C
REPRESENTS A CRITICAL DIMENSION.
SUB-TTF-30100-10-XX
2. SUB-TTF LENGTH IS EQUAL TO HQDP LENGTH.
(SEE TABLE 1 FOR QTY)
C2
3. ALL ASSEMBLIES TO BE 100% ELECTRICALLY TESTED
FOR SHORTS AND OPENS.
C3
4. ALL ASSEMBLIES TO BE 100% HI-POT TESTED AT 300V.
5. TOP SUB-TTF NOT SHOWN IN THIS VIEW FOR CLARITY; HDRL-11
TO BE CENTERED ON LOWER SUB-TTF AS SHOWN; HDRL-11 IS
TO CONTAIN PART NUMBER, SHOP NUMBER, LINE NUMBER &
DATE CODE.
6. PACKAGE ASSEMBLIES IN STATIC DISSIPATIVE BAGS.
7. PARTS TO BE PROCESSED PER SAMTEC ACCEPTABLILITY REQUIREMENTS:
HDR-PI-01 "CABLE ASSEMBLY WORKMANSHIP STANDARDS".
8. CABLE LENGTHS LONGER THAN 40.00 INCHES ARE NOT SUPPORTED BY
S.I. TEST DATA.
9. RT1 OPTION IS NOT AVAILABLE WITH EDGEMOUNT & PANEL MOUNT END OPTIONS.
10. RT1 OPTION IS NOT AVAILABLE WITH -080 PAIRS.
11. DIFFERENTIAL PAIRS CONSIST OF ADJACENT PINS. FOR EXAMPLE, PIN POSITIONS
1 AND 3, 2 AND 4, 5 AND 7, ETC
* "C" REF
LENGTH REF
HQDP-XX-02
Pb
THIS PRODUCT MANUFACTURED
WITH LEAD-FREE PROCESSING
* -DV END OPTIONS ONLY
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
DECIMALS
DETAIL 'A'
SCALE 2.5 : 1
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
.XX: .01 [.3]
2
.XXX: .005 [.13]
.XXXX: .0020 [.051]
ANGLES
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail: info@SAMTEC.com
code: 55322
DESCRIPTION:
DWG. NO.
MATERIAL:
DO NOT SCALE DRAWING
SHEET SCALE: 1:1
0.5mm HIGH-SPEED TWIN-AX CABLE ASSEMBLY
HQDP-XXX-XX.XX-XXX-XXX-X-X
SHEET
1
OF
7
c:\enterprisevault\DWG\MISC\MKTG\HQDP-XXX-XX.XX-XXX-XXX-X-X-MKT.SLDDRW
BY:
BRATCHER 11/18/03
REVISION N
N-1
N
FIRST END - EDGE MOUNT (SEE TABLE 9, SHEET 7)
COVERS BROKEN OUT FOR CLARITY OF WIRE TERMINATION
SECOND END - EDGE MOUNT (SEE TABLE 9, SHEET 7)
COVERS BROKEN OUT FOR CLARITY OF WIRE TERMINATION
T1
-TED
T
B
B20
T1
2
1
T
-TED
-TEU
-TEU
N
N-1
B
B20
2
1
1
2
T
T20
N-1
N
T20
T
B
B1
T1
B
1
2
B1
N
N-1
T1
-SEU
1
2
-SED
T
B
N-1
N
-SEU
1
T
-SED
N-1
N
T20
T
B20
1
2
T20
T
2
B
B20
N
N-1
B
N-1
N
B1
B
B1
2
1
EDGE MOUNT (NO CAPTIVE PANEL SCREWS)
(HQDP-020-XX.XX-TEU-STR-X SHOWN)
(SAME AS FIG. 1, UNLESS OTHERWISE STATED)
.301 7.64
REF
LENGTH: XX.XX + "L" REF (SEE TABLE 4, SHEET 1)
FIG. 2
"D" REF
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail: info@SAMTEC.com
code: 55322
DESCRIPTION:
DO NOT SCALE DRAWING
0.5mm HIGH-SPEED TWIN-AX CABLE ASSEMBLY
DWG. NO.
SUB-HQDP-X-XXX-03-XX
HQDP-XX-03 (TYP)
c:\enterprisevault\DWG\MISC\MKTG\HQDP-XXX-XX.XX-XXX-XXX-X-X-MKT.SLDDRW
SHEET SCALE: 1:1
HQDP-XXX-XX.XX-XXX-XXX-X-X
SHEET
4
OF
7
BY:
BRATCHER 11/18/03
REVISION N
EDGE MOUNT (WITH CAPTIVE PANEL SCREWS)
(HQDP-020-XX.XX-SEU-XXX-1-F SHOWN)
(SAME AS FIG. 2, UNLESS OTHERWISE STATED)
.500 12.70
REF (TYP)
(FULLY TIGHTENED)
FIG. 3
DOUBLE VERTICAL (WITH SCREW DOWN OPTION)
(HQDP-020-XX.XX-TTR-XXX-1-F SHOWN)
(SAME AS FIG. 1, UNLESS OTHERWISE STATED)
.228 5.79
.129 3.28 REF (TYP)
REF
FIG. 4
HQDP-XX-01
CPS-4-40-01-X
"G" REF
"F" REF
"E" REF
"H" REF
"J" REF
HQDP-XX-03-CPS (TYP)
HQDP-XX-02-SDO
.250 6.34
REF (TYP)
(HQDP-020-XX.XX-TEU-STR-N SHOWN)
(SAME AS FIG. 1, UNLESS OTHERWISE STATED)
SUB-HQDP-X-XXX-03-XX
SUB-TTF-XX-XX-XXX-XX.XX
SUB-HQDP-X-XXX-XX-XX
FIG. 5
"N"
(SEE TABLE 9)
"M"
(SEE TABLE 9)
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail: info@SAMTEC.com
code: 55322
DESCRIPTION:
DWG. NO.
DO NOT SCALE DRAWING
0.5mm HIGH-SPEED TWIN-AX CABLE ASSEMBLY
APPLY UV EPOXY TO ALL CABLE ENDS
(HEIGHT NOT TO EXCEED .089[2.26] ABOVE PCB SURFACE)
c:\enterprisevault\DWG\MISC\MKTG\HQDP-XXX-XX.XX-XXX-XXX-X-X-MKT.SLDDRW
SHEET SCALE: 1.25:1
HQDP-XXX-XX.XX-XXX-XXX-X-X
SHEET
5
OF
7
BY:
BRATCHER 11/18/03
MEMS sensors
京公网安备 11010802033920号
EEWORLD
