The EL5191C amplifier is of the current feedback variety and exhibits
a very high bandwidth of 1GHz. This makes this amplifier ideal for
today’s high speed video and monitor applications, as well as a num-
ber of RF and IF frequency designs.
With a supply current of just 9mA and the ability to run from a single
supply voltage from 5V to 10V, these amplifiers offer very high per-
formance for little power consumption.
For applications where board space is critical, the EL5191C is offered
in the 5-pin SOT23 package, as well as an industry standard 8-pin SO.
The EL5191C operates over the industrial temperature range of -40°C
to +85°C.
Applications
•
•
•
•
•
•
Video Amplifiers
Cable Drivers
RGB Amplifiers
Test Equipment
Instrumentation
Current to Voltage Converters
Pin Configurations
8-Pin SO
Ordering Information
Part No
EL5191CW-T7
EL5191CW-T13
EL5191CS
EL5191CS-T7
EL5191CS-T13
Package
5-Pin SOT23
5-Pin SOT23
8-Pin SO
8-Pin SO
8-Pin SO
Tape &
Reel
7”
13”
-
7”
13”
5-Pin SOT23
NC 1
OUT 1
Outline #
8
7
6
5
EL5191CS
NC*
V
S
+
OUT
NC
5 V
S
+
IN- 2
-
IN+ 3
4 IN-
V
S
- 4
EL5191CW
* This pin must be left disconnected
+
-
+
MDP0038
MDP0038
MDP0027
MDP0027
MDP0027
V
S
- 2
IN+
3
April 12, 2001
Note:
All information contained in this data sheet has been carefully checked and is believed to be accurate as of the date of publication; however, this data sheet cannot be a “controlled document”. Current revisions, if any, to these
specifications are maintained at the factory and are available upon your request. We recommend checking the revision level before finalization of your design documentation.
Values beyond absolute maximum ratings can cause the device to be pre-
maturely damaged. Absolute maximum ratings are stress ratings only and
functional device operation is not implied.
11V
Supply Voltage between V
S
+ and V
S
-
Maximum Continuous Output Current
50mA
Operating Junction Temperature
Power Dissipation
Pin Voltages
Storage Temperature
Operating Temperature
125°C
See Curves
V
S
- - 0.5V to V
S
+ +0.5V
-65°C to +150°C
-40°C to +85°C
Important Note:
All parameters having Min/Max specifications are guaranteed. Typ values are for information purposes only. Unless otherwise noted, all tests are at the
specified temperature and are pulsed tests, therefore: T
J
= T
C
= T
A
.
Electrical Characteristics
V
S
+ = +5V, V
S
- = -5V, R
F
= 392Ω for A
V
= 1, R
F
= 250Ω for A
V
= 2, R
L
= 150Ω, T
A
= 25°C unless otherwise specified.
Parameter
AC Performance
BW
BW1
SR
ts
e
n
i
n
-
i
n
+
dG
dP
V
OS
T
C
V
OS
R
OL
CMIR
CMRR
-ICMR
+I
IN
-I
IN
R
IN
C
IN
V
O
I
OUT
Supply
Is
ON
PSRR
-IPSR
Supply Current
Power Supply Rejection Ratio
- Input Current Power Supply Rejection
No Load, V
IN
= 0V
DC, V
S
= ±4.75V to ±5.25V
DC, V
S
= ±4.75V to ±5.25V
8
55
-2
9
75
2
10.5
mA
dB
µA/V
-3dB Bandwidth
0.1dB Bandwidth
Slew Rate
0.1% Settling Time
Input Voltage Noise
IN- input current noise
IN+ input current noise
Differential Gain Error
Differential Phase Error
Offset Voltage
Input Offset Voltage Temperature Coefficient
Transimpedance
Common Mode Input Range
Common Mode Rejection Ratio
- Input Current Common Mode Rejection
+ Input Current
- Input Current
Input Resistance
Input Capacitance
Output Voltage Swing
Output Current
R
L
= 150Ω to GND
R
L
= 1KΩ to GND
R
L
= 10Ω to GND
±3.4
±3.8
95
Measured from T
MIN
to T
MAX
150
±3
42
-6
-120
-40
40
5
27
0.5
±3.7
±4.0
120
[1]
[1]
Description
A
V
= +1
A
V
= +2
Conditions
Min
Typ
1000
600
30
Max
Unit
MHz
MHz
MHz
V/µs
ns
nV/√Hz
pA/√Hz
pA/√Hz
%
°
V
O
= -2.5V to +2.5V, A
V
= +2
V
OUT
= -2.5V to +2.5V, A
V
= -1
2500
2800
7
3.8
25
55
A
V
= +2
A
V
= +2
-15
0.035
0.04
1
5
300
±3.3
50
6
120
40
15
DC Performance
mV
µV/°C
kΩ
V
dB
µA/V
µA
µA
kΩ
pF
V
V
mA
Input Characteristics
Output Characteristics
1. Standard NTSC test, AC signal amplitude = 286mV
As engineers and developers, our job is to find the best way to put all the components together. Whether it's a skyscraper or an integrated circuit, the internal engineering structure is one of the ke...
The current transformer detects the mains power of 50Hz, and the signal is an AC signal. How does the microcontroller process the AC signal? Can we just connect a resistor in series on the hardware ci...
[i=s]This post was last edited by qwqwqw2088 on 2019-7-25 16:17[/i]High frequency critical conduction mode (CrM) totem pole power factor correction (PFC) is a simple approach to design high density po...
While power management is important to almost all electronic devices, it is not often the focus. Power management systems can improve product reliability and performance and often support a wide range...
There are three groups of circuits as shown in the figure (the 6291 above has only one group). If the 1st PIN of CN1 is connected to DGND by mistake during the test, what may happen? There are also so...
[i=s]This post was last edited by DDZZ669 on 2020-10-4 17:28[/i]1 SDRAMRAM can be understood as memory, the space required by the program when running. GD32F450IK comes with 256K RAM. When a large mem...
DSP and ARM Processors
京公网安备 11010802033920号
EEWORLD
