MT-D-O-15-40-S-PMN-4B-FC-1 datasheet, PDF

MT-D-O-15-40-S-PMN-4B-FC-1: DescriptionVariable Attenuator, 1528nm Min, 1563nm Max, 40dB Min, FC/SPC Connector, DIP, Through Hole Mount, DIP-14; CategoryWireless rf/communication Optical fiber; File Size166KB，2 Pages; ManufacturerDicon Fiberoptics Inc; Websitehttp://www.diconfiberoptics.com

Download Datasheet Parametric View All

MT-D-O-15-40-S-PMN-4B-FC-1 Overview

Variable Attenuator, 1528nm Min, 1563nm Max, 40dB Min, FC/SPC Connector, DIP, Through Hole Mount, DIP-14

Parameter Name	Attribute value
package instruction	DIP
Reach Compliance Code	unknown
minimum attenuation	40 dB
body width	12.7 mm
body height	7.5 mm
Body length or diameter	20.83 mm
Communication standards	GR-1221
Connection Type	FC/SPC CONNECTOR
Fiber optic equipment types	VARIABLE ATTENUATOR
Installation features	THROUGH HOLE MOUNT
Maximum operating wavelength	1563 nm
Minimum operating wavelength	1528 nm
Nominal operating wavelength	1546 nm
Package form	DIP
surface mount	NO
change control organization	VOLTAGE
Base Number Matches	1

Attenuators

PM MEMS Attenuator

DiCon’s PM MEMS Attenuator is based on a micro-electro-

mechanical system (MEMS) chip. The MEMS chip consists of an

electrically movable mirror on a silicon support. A voltage applied

to the MEMS chip causes the mirror to rotate, which changes the

coupling of light between the input and output fibers of the

MEMS Attenuator.

Cylindrical Package

Features

•

Small attenuator package

High extinction ratio

Qualified to GR-1221

Available in opaque or transparent versions

Available in both cylindrical and 14-pin DIP packages

Applications

MEMS Attenuators are used for distributed power equalization within

OADMs, MUX/DMUXes, Band Equalizers, Channel Equalizers, Optical

Cross-Connects, Line Cards and Transponders. Polarization Maintaining

Attenuators can also be used for power adjustment in polarization

sensitive devices such as modulators.

Knowledge of common op amp models: Common op amp model knowledgeCA3130 high input impedance operational amplifier Intersil [DATA] CA3140 High Input Impedance Operational Amplifier CD4573 Quad Programmable Operational Amplifier MC14573 ...; fish001 Analogue and Mixed Signal

These two methods make electric vehicles run farther in winter: As electric bicycles and electric motorcycles become more popular, consumers are demanding longer battery life. Extending the battery life of a battery pack allows the vehicle to travel further withou...; EEWORLD社区 TI Technology Forum

Voltage Follower: Because the sensor signal is relatively weak, direct amplification will cause signal distortion, so we use voltage following and then amplification. After following with LMV612, we found that the volt...; 轩辕默殇 Analog electronics

PCB panelization skills: [i=s]This post was last edited by qwqwqw2088 on 2019-3-29 17:40[/i] [size=4] For PCB panel width ≤260mm～300mm, it varies according to different production lines. Because we may have a lot of materials...; qwqwqw2088 PCB Design

Analysis of the switch input circuit composed of four diodes: This is a switch input circuit composed of four diodes found on the Internet. SW1 is the input terminal, and VPIN is connected to the microcontroller input terminal, which is in a high-impedance state...; bigbat Analog electronics

Questions about TEC control chip ADN8834: I bought a development board: ADN8834CP-EVALZ to control the temperature of the laser module, but the temperature cannot be controlled. My approach is as follows:1. I want to control the temperature a...; xiaxingxing Analog electronics

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components