EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

12145AK-13CECC

Description
Toggle Switch, DPDT, Momentary, 4A, 30VDC, Solder Terminal, Standard Type Actuator, Panel Mount-threaded
CategoryMechanical and electronic products    switch   
File Size622KB,15 Pages
ManufacturerAPEM
Environmental Compliance
Download Datasheet Parametric View All

12145AK-13CECC Overview

Toggle Switch, DPDT, Momentary, 4A, 30VDC, Solder Terminal, Standard Type Actuator, Panel Mount-threaded

12145AK-13CECC Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
Reach Compliance Codecompliant
ECCN codeEAR99
Actuator typeSTANDARD TYPE
body width14 mm
body height13.7 mm
Body length or diameter14 mm
Contact (AC) maximum rated R load4A@125VAC
Maximum contact current (AC)4 A
Maximum contact current (DC)4 A
Contact (DC) maximum rated R load4A@30VDC
Maximum contact voltage (AC)125 V
Maximum contact voltage (DC)30 V
Electrical life50000 Cycle(s)
Manufacturer's serial number12000
Installation featuresPANEL MOUNT-THREADED
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
method of packingBULK
sealDUST PROOF; WATER PROOF
surface mountNO
Switch actionMOMENTARY
switch functionDPDT
Switch typeTOGGLE SWITCH
Termination typeSOLDER
Base Number Matches1
[Solved] How to start DSP on ARM
[size=4] I have never been exposed to heterogeneous processing before, so I don't know the specific steps. Now in the example program, the ARM side sends messages to the DSP and then prints the inform...
Jacktang DSP and ARM Processors
Recruitment position in Xiamen IC design company: MCU product development engineer
Our company is recruiting senior MCU product development engineers:Job Responsibilities 1. Responsible for the development of small signal module products 2. Responsible for product schematic design a...
RichLin Recruitment
【Running posture training shoes】No.006-Bluetooth communication program design
The previous article introduced the algorithm part, posture recognition and cadence calculation . This article introduces the design process of the Bluetooth communication program. For the Bluetooth c...
sipower onsemi and Avnet IoT Innovation Design Competition
Can STM32 use a timer to control PWM output
There are two waveforms, one is wider PWM1, and the other is narrower PWM2. The requirement is that when PWM1 is at a high level, PWM2 has output, and when PWM1 is at a low level, PWM2 has no output. ...
bigbat stm32/stm8
The constant temperature crystal oscillator power supply is 5V and the output is CMOS. How to connect it to the 3.3VBANK of FPGA?
The constant temperature crystal oscillator power supply is 5V and the output is CMOS. How to connect it to the 3.3VBANK of FPGA?...
采样电阻 FPGA/CPLD
As shown in the figure, the netlist is transferred to the PCB, and these four networks form GND_SIGNAL_20640, which is not connected to GND_SIGNAL.
[font=宋体][size=4]As shown in the figure, 6 networks are connected to GND_SIGNAL, but the GND_SIGNAL on this page of the PCB is connected together when the netlist is called, but it is not connected to...
Syber PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号