ISOCOM
COM-
ICPLM600, ICPLM601
DESCRIPTION
The ICPLM600 and ICPLM601 devices each consists
of an infrared emitting diode optically coupled to a high
speed integrated photo detector logic gate.
These devices belong to Isocom Compact Range of
optocouplers.
1
3
4
5
6
Anode
Cathode
GND
V
O
V
CC
FEATURES
•
•
•
•
•
•
•
High speed 10Mbit/s
Half Pitch 1.27mm
Common Mode Transient Immunity
5kV/μs min. (ICPLM601)
High AC Isolation Voltage 3750V
RMS
Guaranteed Performance from -40°C to 85°C
Pb Free and RoHS Compliant
Safety Approvals Pending
V
CC
must be bypassed by a A 0.1μF capacitor.
APPLICATIONS
•
•
•
•
•
•
•
Line Receivers, Data Communication
LSTTL to TTL, LSTTL or 5V CMOS
Data Multiplexing
Pulse Transformer Replacement
Switch Mode Power Supplies
Ground Loop Elimination
Computer Peripheral Interface
ABSOLUTE MAXIMUM RATINGS
(T
A
= 25°C)
Stresses exceeding the absolute maximum ratings can cause
permanent damage to the device.
Exposure to absolute maximum ratings for long periods of time
can adversely affect reliability.
Input
Forward Current
Reverse Voltage
Power dissipation
Output
Output Current
Output Voltage
Supply Voltage
Power Dissipation
Total Package
Isolation Voltage
Operating Temperature
Storage Temperature
Lead Soldering Temperature
(10s)
50mA
5V
100mW
ORDER INFORMATION
•
Available in Tape and Reel with 3000pcs
per reel.
50mA
7V
7V
85mW
3750V
RMS
-40 to 85 °C
-40 to 125 °C
260°C
ISOCOM COMPONENTS 2004 LTD
Unit 25B, Park View Road West, Park View Industrial Estate
Hartlepool, Cleveland, TS25 1PE, United Kingdom
Tel : +44 (0)1429 863 609 Fax : +44 (0)1429 863 581
e-mail : sales@isocom.co.uk
http://www.isocom.com
ISOCOM COMPONENTS ASIA LTD
Hong Kong Office,
Block A, 8/F, Wah Hing Industrial mansion,
36 Tai Yau Street, San Po Kong, Kowloon, Hong Kong.
Tel : +852 2995 9217 Fax : +852 8161 6292
e-mail : sales@isocom.com.hk
1 19/04/2017
DD93212
ISOCOM
COM-
ICPLM600, ICPLM601
ELECTRICAL CHARACTERISTICS
Notes :
1. The V
CC
supply must be bypassed by a 0.1μF capacitor or larger with good high frequency characteristic and
should be connected as close as possible to the package V
CC
and GND pins.
2. t
PLH
– Propagation delay is measured from the 3.75mA level on the HIGH to LOW transition of the input current
pulse to the 1.5 V level on the LOW to HIGH transition of the output voltage pulse.
3. t
PHL
– Propagation delay is measured from the 3.75mA level on the LOW to HIGH transition of the input current
pulse to the 1.5 V level on the HIGH to LOW transition of the output voltage pulse.
4. t
PSK
̶
The magnitude of the worst case difference in t
PHL
and/or t
PLH
that will be seen between devices at any
given temperature within the worst case operating condition range.
4 t
r
– Rise time is measured from the 10% to the 90% levels on the LOW to HIGH transition of the output pulse.
5. t
f
– Fall time is measured from the 90% to the 10% levels on the HIGH to LOW transition of the output pulse.
6. CM
H
– The maximum tolerable rate of rise of the common mode voltage to ensure the output will remain in the
HIGH state (i.e., V
OUT
> 2.0V).
7. CM
L
– The maximum tolerable rate of rise of the common mode voltage to ensure the output will remain in the
LOW output state (i.e., V
OUT
< 0.8V).
4 19/04/2017
DD93212
ISOCOM
COM-
ICPLM600, ICPLM601
Fig 1 Forward Current vs Forward Voltage
Fig 2 Output Voltage vs Forward Current
Fig 3 Input Threshold Current vs T
A
Fig 4 Low Level Output Voltage vs T
A
Fig 5 Low Level Output Current vs T
A
Fig 6 High Level Output Current vs T
A
5 19/04/2017
DD93212
京公网安备 11010802033920号
EEWORLD
