1N3016BUR-1 – 1N3045BUR-1
Available on
commercial
versions
1 Watt Surface Mount
Zener Diodes
Qualified per MIL-PRF-19500/115
DESCRIPTION
Qualified Levels:
JAN, JANTX, and
JANTXV
This surface mountable Zener diode series is similar to the 1N3016B-1 through 1N3045B-1
JEDEC registration in the DO-13 package except that it meets the surface mount DO-213AB
outline. It is an ideal selection for applications of high density and low parasitic requirements.
Due to its glass hermetic seal qualities and metallurgically enhanced internal construction, it is
also well suited for high-reliability applications where it is available in JAN, JANTX, and
JANTXV military qualifications. Lower voltages are also available in the 1N3821AUR-1
through 1N3828AUR-1 series (3.3 V to 7.5 V) in the same package (see separate data sheet).
Important:
For the latest information, visit our website
http://www.microsemi.com.
DO-213AB (MELF,
LL41) Package
FEATURES
•
•
•
•
•
•
•
Leadless surface mount equivalents to the JEDEC registered 1N3016 through 1N3045 number
series.
Zener voltage range: 6.8 volts to 110 volts.
Hermetically sealed, double plug glass construction.
Metallurgically bonded.
Voltage tolerances of 5%, 2%, and 1% available.
JAN, JANTX, and JANTXV qualifications also available per MIL-PRF-19500/115.
(See
part nomenclature
for all available options.)
RoHS compliant versions available (commercial grade only).
Also available in:
DO-41 package
(glass axial-leaded)
1N3016B-1 – 1N3045B-1
APPLICATIONS / BENEFITS
•
•
•
•
•
•
•
•
Regulates voltage over a broad operating current and temperature range.
Wide selection from 6.8 to 110 V.
Low reverse (leakage) currents.
Leadless package for surface mounting.
Ideal for high-density situations.
Metallurgically enhanced internal contact design for greater reliability and lower thermal resistance.
Non-sensitive to ESD.
Inherently radiation hard as described in Microsemi “MicroNote
050”.
MAXIMUM RATINGS
Parameters/Test Conditions
Junction and Storage Temperature
Thermal Resistance Junction-to-End Cap
(1)
DC Power Dissipation
Forward Voltage @ 200 mA
Solder Temperature @ 10 s
Symbol
T
J
and T
STG
R
ӨJEC
P
D
V
F
T
SP
Value
-55 to +175
50
1.0
1.2
260
Unit
ºC
ºC/W
W
V
o
C
MSC – Lawrence
6 Lake Street,
Lawrence, MA 01841
Tel: 1-800-446-1158 or
(978) 620-2600
Fax: (978) 689-0803
MSC – Ireland
Gort Road Business Park,
Ennis, Co. Clare, Ireland
Tel: +353 (0) 65 6840044
Fax: +353 (0) 65 6822298
Website:
www.microsemi.com
Notes:
1. Derate linearly starting at T
EC
125 ºC to zero at 175 ºC (see
Figure1).
T4-LDS-0285-1, Rev. 1 (4/22/13)
©2013 Microsemi Corporation
Page 1 of 5
1N3016BUR-1 – 1N3045BUR-1
MECHANICAL and PACKAGING
•
•
•
•
•
•
•
•
CASE: Hermetically sealed glass MELF package.
TERMINALS: Tin/lead or RoHS compliant matte-tin finished copper clad steel available (commercial grade only). Solderable per
MIL-STD-750, method 2026.
MARKING: Cathode band.
POLARITY: Diode to be operated with the banded end positive with respect to the opposite end for Zener regulation.
MOUNTING SURFACE SELECTION: The Axial Coefficient of Expansion (COE) of this device is approximately +6PPM/°C. The
COE of the Mounting Surface System should be selected to provide a suitable match with this device.
TAPE & REEL optional: Standard per EIA-481-1-A with 12 mm tape. Consult factory for quantities.
WEIGHT: Approximately 0.05 grams.
See
Package Dimensions
on last page.
PART NOMENCLATURE
JAN
Reliability Level
JAN = JAN level
JANTX = JANTX level
JANTXV = JANTXV level
Blank = Commercial
JEDEC type number
(See
Electrical Characteristics
table)
Zener Voltage Tolerance
B = 5%
C = 2%
D = 1%
1N3016 B
UR
-1
e3
RoHS Compliance
e3 = RoHS compliant (available
on commercial grade only)
Blank = non-RoHS compliant
Metallurgically Bonded
Surface Mount MELF Package
Symbol
I
R
I
Z
, I
ZT
, I
ZK
I
ZM
V
F
V
R
V
Z
Z
ZT
or Z
ZK
SYMBOLS & DEFINITIONS
Definition
Reverse Current: The maximum reverse (leakage) current that will flow at the specified voltage and temperature.
Regulator Current: The dc regulator current (I
Z
), at a specified test point (I
ZT
), near breakdown knee (I
ZK
).
Maximum Regulator (Zener) Current: The maximum rated dc current for the specified power rating.
Maximum Forward Voltage: The maximum forward voltage the device will exhibit at a specified current.
Reverse Voltage: The reverse voltage dc value, no alternating component.
Zener Voltage: The Zener voltage the device will exhibit at a specified current (I
Z
) in its breakdown region.
Dynamic Impedance: The small signal impedance of the diode when biased to operate in its breakdown region at a
specified rms current modulation (typically 10% of I
ZT
or I
ZK
) and superimposed on I
ZT
or I
ZK
respectively.
T4-LDS-0285-1, Rev. 1 (4/22/13)
©2013 Microsemi Corporation
Page 2 of 5
1N3016BUR-1 – 1N3045BUR-1
*ELECTRICAL CHARACTERISTICS
@ 25 °C
NOMINAL
ZENER
VOLTAGE
V
Z
@ I
ZT
(Note 1)
Volts
6.8
7.5
8.2
9.1
10
11
12
13
15
16
18
20
22
24
27
30
33
36
39
43
47
51
56
62
68
75
82
91
100
110
ZENER
TEST
CURRENT
I
ZT
mA
37
34
31
28
25
23
21
19
17
15.5
14
12.5
11.5
10.5
9.5
8.5
7.5
7.0
6.5
6.0
5.5
5.0
4.5
4.0
3.7
3.3
3.0
2.8
2.5
2.3
MAXIMUM ZENER IMPEDANCE
(Note 3)
MAXIMUM
ZENER
CURRENT
I
ZM
(Note 3)
mA
140
125
115
105
95
85
80
74
63
60
52
47
43
40
34
31
28
26
23
21
19
18
17
15
14
12
11
10
9.0
8.3
MAXIMUM
REVERSE
LEAKAGE
CURRENT†
I
R
@ V
R
µA
Volts
150
5.2
100
5.7
50
6.2
25
6.9
25
7.6
10
8.4
10
9.1
10
9.9
10
11.4
10
12.2
10
13.7
10
15.2
10
16.7
10
18.2
10
20.6
10
22.8
10
25.1
10
27.4
10
29.7
10
32.7
10
35.8
10
38.8
10
42.6
10
47.1
10
51.7
10
56.0
10
62.2
10
69.2
10
76.0
10
83.6
MAXIMUM
TEMP. COEFF.
OF ZENER
VOLTAGE
α
VZ
%/
o
C
0.061
0.065
0.070
0.073
0.076
0.078
0.081
0.085
0.088
0.089
0.091
0.092
0.093
0.094
0.096
0.098
0.099
0.100
0.101
0.102
0.102
0.103
0.103
0.104
0.104
0.105
0.106
0.108
0.11
0.11
JEDEC TYPE
NUMBER
1N3016BUR-1
1N3017BUR-1
1N3018BUR-1
1N3019BUR-1
1N3020BUR-1
1N3021BUR-1
1N3022BUR-1
1N3023BUR-1
1N3024BUR-1
1N3025BUR-1
1N3026BUR-1
1N3027BUR-1
1N3028BUR-1
1N3029BUR-1
1N3030BUR-1
1N3031BUR-1
1N3032BUR-1
1N3033BUR-1
1N3034BUR-1
1N3035BUR-1
1N3036BUR-1
1N3037BUR-1
1N3038BUR-1
1N3039BUR-1
1N3040BUR-1
1N3041BUR-1
1N3042BUR-1
1N3043BUR-1
1N3044BUR-1
1N3045BUR-1
Z
ZT
@ I
ZT
Ohms
3.5
4.0
4.5
6
7
8
9
10
14
16
20
22
23
25
35
40
45
50
60
70
80
95
110
125
150
175
200
250
350
450
Z
ZK
@ I
ZK
Ohms
mA
700
1.0
700
.5
700
.5
700
.5
700
.25
700
.25
700
.25
700
.25
700
.25
700
.25
750
.25
750
.25
750
.25
750
.25
750
.25
1000
.25
1000
.25
1000
.25
1000
.25
1500
.25
1500
.25
1500
.25
2000
.25
2000
.25
2000
.25
2000
.25
3000
.25
3000
.25
3000
.25
4000
.25
*JEDEC Registered Data.
NOTES:
1.
2.
†Not JEDEC Data.
Zener voltage (
V
Z
) is measured with junction in thermal equilibrium with still air at a temperature of 25
o
C. The test currents (I
ZT
) at
nominal voltages provide a constant 0.25 watts.
The Zener impedance is derived when a 60 cycle ac current having an rms value equal to 10% of the dc Zener current (I
ZT
or
I
ZK
) is superimposed on I
ZT
or I
ZK
. Zener impedance is measured at 2 points to ensure a sharp knee on the breakdown curve
and to eliminate unstable units. See
MicroNote 202
for variation in dynamic impedance with different Zener currents.
These values of I
ZM
may often be exceeded in the case of individual diodes. The values shown are calculated for a unit at the high
voltage end of its tolerance range. Allowance has also been made for the rise in Zener voltage above V
ZT
that results from Zener
impedance and the increase in junction temperature as a unit approaches thermal equilibrium at a dissipation of 1 watt. The I
ZM
values shown for +/- 5% tolerance units may be used with little error for +/- 10% tolerance units, but should be reduced by 7% to
include a +/- 20% tolerance unit near the high voltage end of its tolerance range.
3.
T4-LDS-0285-1, Rev. 1 (4/22/13)
©2013 Microsemi Corporation
Page 3 of 5
1N3016BUR-1 – 1N3045BUR-1
GRAPHS
DC Operation Maximum Rating (W)
T
EC
(ºC) (End Cap)
FIGURE 1
Temperature-Power Derating Curve
T4-LDS-0285-1, Rev. 1 (4/22/13)
©2013 Microsemi Corporation
Page 4 of 5
1N3016BUR-1 – 1N3045BUR-1
PACKAGE DIMENSIONS
Symbol
BD
BL
ECT
S
Dimensions
Inch
Millimeters
Min
Max
Min
Max
0.094
0.105
2.39
2.67
0.189
0.205
4.80
5.21
0.014
0.022
0.360 0.560
0.001 min
0.03 min
NOTES:
1. Dimensions are in inches. Millimeters are given for general information only.
2. Gap not controlled, shape of body and gap not controlled.
3. In accordance with ASME Y14.5M, diameters are equivalent to
Φx
symbology.
PAD LAYOUT
Ltr
A
B
C
Inch
0.276
0.070
0.110
mm
7.00
1.8
2.8
T4-LDS-0285-1, Rev. 1 (4/22/13)
©2013 Microsemi Corporation
Page 5 of 5
京公网安备 11010802033920号
EEWORLD
