5200 Series NAND Flash SSD
Features
5200 Series SATA NAND Flash SSD
MTFDDAK240T, MTFDDAK480T, MTFDDAK960T, MTFDDAK1T9T,
MTFDDAK3T8T, MTFDDAK7T6T
Features
• Micron
®
3D TLC NAND Flash
• Three performance/endurance levels
– ECO
– PRO
– MAX
• TCG Enterprise compliant self-encrypting drive
(SED)
• SATA 6 Gb/s interface
• ATA modes supported
– PIO mode 3, 4
– Multiword DMA mode 0, 1, 2
– Ultra DMA mode 0, 1, 2, 3, 4, 5, 6
• 512-byte sector size support
• Hot-plug capable
• Native command queuing support with 32-com-
mand slot support
• ATA-8 ACS-3 revision 5 command set compliant
• ATA security feature command set and password
login support
• Security erase command set: fast and secure erase
• Performance (steady state)
1
– Sequential 128KB read: Up to 540 MB/s
– Sequential 128KB write: Up to 520 MB/s
– Random 4KB read: Up to 95,000 IOPS
– Random 4KB write: Up to 75,000 IOPS
• Quality of Service
2
– Read/Write (99.9%): 200µs/300µs (<2TB)
– Read/Write (99.999%): 1000µs/700µs (<2TB)
• Endurance
4
: Total bytes written (TBW)
– Up to 17600TB
• Reliability
– MTTF: 3.0 million device hours
3
– Static and dynamic wear leveling
– Uncorrectable bit error rate (UBER): <1 sector
per 10
17
bits read
– End-to-end data protection
– Enhanced power-loss data protection with data
protection capacitor monitoring
• Self-monitoring, analysis, and reporting technology
(SMART) command set
• Capacity
4
(unformatted): 240GB, 480GB, 960GB,
1920GB, 3840GB, 7680GB
• Mechanical:
– 2.5-inch x 7.0mm form factor
• RoHS-compliant package
• Secure field-upgradeable firmware with digitally
signed firmware image
• Power consumption: <6.0W (TYP 5V only)
,
• Operating temperature
– Commercial (0°C to 70°C)
5
Notes:
1. Performance varies by capacity and endur-
ance.
2. 4KB transfers QD = 1 used for READ/WRITE
latency values.
3. The product achieves a MTTF based on pop-
ulation statistics not relevant to individual
units.
4. 1GB = 1 billion bytes.
5. As reported by SMART.
Warranty:
Contact your Micron sales representative
for further information regarding the product,
including product warranties.
CCMTD-731836775-10503
5200_series_ssd.pdf - Rev. E 05/18 EN
1
Products and specifications discussed herein are subject to change by Micron without notice.
Micron Technology, Inc. reserves the right to change products or specifications without notice.
©
2017 Micron Technology, Inc. All rights reserved.
5200 Series NAND Flash SSD
Features
Part Numbering Information
Micron’s 5200 SSD is available in different configurations and densities. The chart below is a comprehensive list of
options for the 5200 series devices; not all options listed can be combined to define an offered product. Visit
mi-
cron.com
for a list of valid part numbers.
Figure 1: Part Number Chart
MT FD
Micron Technology
Product Family
FD = Flash drive
D
AK 960 T
DC - 1
AT
1
6
AB
YY
ES
Production Status
Blank = Production
ES = Engineering sample
Customer Designator
YY = Standard
Drive Interface
D = SATA 6.0 Gb/s
Hardware Features
AB = Standard
TA = TAA Compliant
Drive Form Factor
AK = 2.5-inch (7mm)
Drive Capacity
240 = 240GB
480 = 480GB
960 = 960GB
1T9 = 1920GB
3T8 = 3840GB
7T6 = 7680GB
Extended Firmware Features
Z = None
6 = SED TCG eSSC
Sector Size
1 = 512 byte
NAND Flash Type
T = TLC
NAND Flash Component
AT = 512Gb, TLC, x8, 3.3V (3D)
Product Family
DC = 5200 ECO
DD = 5200 PRO
DN = 5200 MAX
BOM Revision
For example:
1 = 1st generation
2 = 2nd generation
CCMTD-731836775-10503
5200_series_ssd.pdf - Rev. E 05/18 EN
2
Micron Technology, Inc. reserves the right to change products or specifications without notice.
©
2017 Micron Technology, Inc. All rights reserved.
5200 Series NAND Flash SSD
Important Notes and Warnings
Important Notes and Warnings
Micron Technology, Inc. ("Micron") reserves the right to make changes to information published in this document,
including without limitation specifications and product descriptions. This document supersedes and replaces all
information supplied prior to the publication hereof. You may not rely on any information set forth in this docu-
ment if you obtain the product described herein from any unauthorized distributor or other source not authorized
by Micron.
Automotive Applications.
Products are not designed or intended for use in automotive applications unless specifi-
cally designated by Micron as automotive-grade by their respective data sheets. Distributor and customer/distrib-
utor shall assume the sole risk and liability for and shall indemnify and hold Micron harmless against all claims,
costs, damages, and expenses and reasonable attorneys' fees arising out of, directly or indirectly, any claim of
product liability, personal injury, death, or property damage resulting directly or indirectly from any use of non-
automotive-grade products in automotive applications. Customer/distributor shall ensure that the terms and con-
ditions of sale between customer/distributor and any customer of distributor/customer (1) state that Micron
products are not designed or intended for use in automotive applications unless specifically designated by Micron
as automotive-grade by their respective data sheets and (2) require such customer of distributor/customer to in-
demnify and hold Micron harmless against all claims, costs, damages, and expenses and reasonable attorneys'
fees arising out of, directly or indirectly, any claim of product liability, personal injury, death, or property damage
resulting from any use of non-automotive-grade products in automotive applications.
Critical Applications.
Products are not authorized for use in applications in which failure of the Micron compo-
nent could result, directly or indirectly in death, personal injury, or severe property or environmental damage
("Critical Applications"). Customer must protect against death, personal injury, and severe property and environ-
mental damage by incorporating safety design measures into customer's applications to ensure that failure of the
Micron component will not result in such harms. Should customer or distributor purchase, use, or sell any Micron
component for any critical application, customer and distributor shall indemnify and hold harmless Micron and
its subsidiaries, subcontractors, and affiliates and the directors, officers, and employees of each against all claims,
costs, damages, and expenses and reasonable attorneys' fees arising out of, directly or indirectly, any claim of
product liability, personal injury, or death arising in any way out of such critical application, whether or not Mi-
cron or its subsidiaries, subcontractors, or affiliates were negligent in the design, manufacture, or warning of the
Micron product.
Customer Responsibility.
Customers are responsible for the design, manufacture, and operation of their systems,
applications, and products using Micron products. ALL SEMICONDUCTOR PRODUCTS HAVE INHERENT FAIL-
URE RATES AND LIMITED USEFUL LIVES. IT IS THE CUSTOMER'S SOLE RESPONSIBILITY TO DETERMINE
WHETHER THE MICRON PRODUCT IS SUITABLE AND FIT FOR THE CUSTOMER'S SYSTEM, APPLICATION, OR
PRODUCT. Customers must ensure that adequate design, manufacturing, and operating safeguards are included
in customer's applications and products to eliminate the risk that personal injury, death, or severe property or en-
vironmental damages will result from failure of any semiconductor component.
Limited Warranty.
In no event shall Micron be liable for any indirect, incidental, punitive, special or consequential
damages (including without limitation lost profits, lost savings, business interruption, costs related to the removal
or replacement of any products or rework charges) whether or not such damages are based on tort, warranty,
breach of contract or other legal theory, unless explicitly stated in a written agreement executed by Micron's duly
authorized representative.
General Description
Micron’s 5200 solid state drive (SSD) uses a single-chip controller with a SATA interface
on the system side and four channels of Micron NAND Flash internally. Available in the
2.5-inch form factor, the SSD integrates easily in existing storage infrastructures.
CCMTD-731836775-10503
5200_series_ssd.pdf - Rev. E 05/18 EN
3
Micron Technology, Inc. reserves the right to change products or specifications without notice.
©
2017 Micron Technology, Inc. All rights reserved.
5200 Series NAND Flash SSD
General Description
The SSD is designed to use the SATA interface efficiently during both READs and
WRITEs while delivering bandwidth-focused performance. SSD technology enables en-
hanced boot times, faster application load times, reduced power consumption and ex-
tended reliability.
The self-encrypting drive (SED) features an AES-256 encryption engine, providing hard-
ware-based, secure data encryption, with no loss of SSD performance. This SED follows
the TCG Enterprise specification for trusted peripherals. When TCG Enterprise features
are not enabled, the device can perform alternate data encryption by invoking the ATA
security command set encryption features, to provide full disk encryption (FDE) man-
aged in the host system BIOS. TCG Enterprise and ATA security feature sets cannot be
enabled simultaneously.
The data encryption is always running; however, encryption keys are not managed and
the data is not secure until either TCG Enterprise or ATA security feature sets are ena-
bled.
Figure 2: Functional Block Diagram
NAND
SATA
SSD
controller
NAND
NAND
NAND
DRAM
buffer
CCMTD-731836775-10503
5200_series_ssd.pdf - Rev. E 05/18 EN
4
Micron Technology, Inc. reserves the right to change products or specifications without notice.
©
2017 Micron Technology, Inc. All rights reserved.
5200 Series NAND Flash SSD
Performance
Performance
Measured performance can vary for a number of reasons. The major factors affecting
drive performance are the capacity of the drive and the interface/HBA of the host. Addi-
tionally, overall system performance can affect the measured drive performance. When
comparing drives, it is recommended that all system variables are the same, and only
the drive being tested varies.
Performance numbers will vary depending on the host system configuration. Perform-
ance is measured using a single drive directly attached (no RAID) to an integrated SATA
controller.
Table 1: Drive Performance – ECO
Capacity
Parameter
Sequential read (128KB transfer)
Sequential write (128KB transfer)
Random read (4KB transfer)
Random write (4KB transfer)
Random 70/30 R/W (4KB transfer)
READ latency (99.9%)
WRITE latency (99.9%)
READ latency (99.999%)
WRITE latency (99.999%)
Notes:
480GB
540
385
81,000
33,000
43,000
200
300
1000
700
960GB
540
520
95,000
28,000
49,000
200
300
1000
700
1920GB
540
520
95,000
22,000
42,000
200
300
1000
700
3840GB
540
520
95,000
17,000
46,000
200
500
1000
10,000
7680GB
540
520
95,000
9500
26,000
200
900
1000
18,000
MB/s
MB/s
IOPS
IOPS
IOPS
µs
µs
µs
µs
Unit
1. Performance measured using FIO with a queue depth of 32 in the steady state region.
2. 4KB transfers with a queue depth of 1 are used to measure READ/WRITE latency values.
3. System variations and HBA used will affect measured results.
Table 2: Drive Performance – PRO
Capacity
Parameter
Sequential read (128KB transfer)
Sequential write (128KB transfer)
Random read (4KB transfer)
Random write (4KB transfer)
Random 70/30 R/W (4KB transfer)
READ latency (99.9%)
WRITE latency (99.9%)
READ latency (99.999%)
WRITE latency (99.999%)
Notes:
960GB
540
520
95,000
32,000
53,000
200
300
1000
700
1920GB
540
520
95,000
32,000
53,000
200
300
1000
700
3840GB
540
520
95,000
24,500
57,000
200
900
2000
18,000
MB/s
MB/s
IOPS
IOPS
IOPS
µs
µs
µs
µs
Unit
1. Performance measured using FIO with a queue depth of 32 in the steady state region.
2. 4KB transfers with a queue depth of 1 are used to measure READ/WRITE latency values.
3. System variations and HBA used will affect measured results.
CCMTD-731836775-10503
5200_series_ssd.pdf - Rev. E 05/18 EN
5
Micron Technology, Inc. reserves the right to change products or specifications without notice.
©
2017 Micron Technology, Inc. All rights reserved.
京公网安备 11010802033920号
EEWORLD
