SIT1602AIR1-30E datasheet, PDF

Datasheet> All Categories > Passive components> SIT1602AIR1-30E

SIT1602AIR1-30E: DescriptionOSC PROG H/LV-CMOS 3V EN/DS SMD; CategoryPassive components; File Size129KB，2 Pages; ManufacturerSiTime; Environmental Compliance

Download Datasheet Parametric View All

SIT1602AIR1-30E Overview

OSC PROG H/LV-CMOS 3V EN/DS SMD

SIT1602AIR1-30E Parametric

Parameter Name	Attribute value
type	MEMS (silicon)
Programmable type	Programmed by Digi-Key (please enter your desired frequency on the website order form)
Available frequency range	3.75MHz ~ 77.76MHz
Function	enable/disable
output	HCMOS，LVCMOS
Voltage - Power	3V
frequency stability	-
Frequency stability (overall)	±20ppm
Operating temperature	-40°C ~ 85°C
spread spectrum bandwidth	-
Current - Power (maximum)	4.5mA
grade	-
Installation type	surface mount
Package/casing	4-SMD, no leads
size/dimensions	0.098" long x 0.079" wide (2.50mm x 2.00mm)
high	0.031"（0.79mm）
Current - Power (disabled) (maximum)	4mA

Preview

Download Datasheet

View All

Aug 2015

FAQ – New revision products

1. What revision B products has SiTime rolled out?

The table below provides a summary of the rev. B part numbers and their rev. A counterparts.

Low Power Oscillators

High-Temp Oscillators

SOT23 Oscillators / Clock

Generators

Rev. B

SiT1602B, SiT8008B,

SiT8009B

SiT1618B, SiT8918B,

SiT8919B, SiT8920B,

SiT8921B

SiT2001B, SiT2002B,

SiT2018B, SiT2019B,

SiT2020B, SiT2021B

Rev. A

SiT1602A, SiT8008A,

SiT8009A

SiT1618A, SiT8918A,

SiT8919A, SiT8920A,

SiT8921A

SiT2001A, SiT2002A,

SiT2018A, SiT2019A,

SiT2020A, SiT2021A

2. Why did SiTime update the product revision to B?

SiTime enabled a programmable option for a very large customer to accommodate their specific

system level requirement. Consequently SiTime is rolling out revision B to all of our customers

in order to maximize our supply chain and inventory management efficiency.

3. What kind of changes has SiTime made on the rev B?

An additional programmable option is enabled in rev B, but spec-wise, rev B is the same as rev

A, except the IDD max value for 3.3V is slightly higher in the new rev.

4. What is the difference between A and B?

Max current consumption is increased by a small account (0.1 to 0.2 mA) in some cases.

5. What is the benefit of using rev B?

The main benefit over time is better lead time as SiTime will have more rev B inventory in the

channel and at tour factory as our large customers have been or are transitioning over to rev B.

6. Will Rev A still be available?

Yes, there will be absolutely no change for our customers who are using rev A in their existing

designs. We will continue to ship in volume to support these designs.

----------------------------------------------------------------------------------------------------------------------------- ---------------

The Smart Timing Choice™

New Revision Products FAQ Rev 1.0

Recommended Resources

Lenovo Rising Sun 150 laptop audio power amplifier

STK4332 audio IC circuit diagram

Switching power supply circuit diagram composed of STR-S5941

Simple parallel voltage regulator circuit

555 hotel security electronic lock device circuit

820e computer motherboard circuit diagram_06

【AT32WB415 Review】03 SPI Drive TFT LCD Screen: 03 SPI drive TFT LCD screen Preface The above has implemented the MCU's IO port, timer, external interrupt and other operations. On this basis, we will implement the driver of the TFT LCD screen for t...; 秦天qintian0303 RF/Wirelessly

MSP430 G2553 Timer/Counter Timer_A: 1. Introduction Timer_A can realize the following functions: - multiple compare: Determines whether the timer reaches the set condition and triggers the event - Multiple capture: Capture the time when...; Jacktang Microcontroller MCU

msp430 program library serial series 12864 LCD: Liquid crystal is one of the most commonly used display devices in the single-chip microcomputer system. This library has been tested on the MSP430F169 and MSP1430F149 microcontrollers and can be used...; 灞波儿奔 Microcontroller MCU

CC2640R2 internal Bootloader burning program: Here is a method to use the internal bootloader of the chip to burn the program. After entering the boot mode, you can use the ordinary serial interface to boot the firmware, erase and program the FLA...; 火辣西米秀 Microcontroller MCU

【ST NUCLEO-H743ZI Review】_by dsjsjf: @dsjsjf [/url] [/size] [size=4] [url=https://en.eeworld.com/bbs/thread-1070200-1-1.html] [ST NUCLEO-H743ZI Review] (1) First look at ST NUCLEO-H743ZI [/url] [/size] [url=https://en.eeworld.com/bbs/thr...; okhxyyo stm32/stm8

【TouchGFX Design】(3) Simple waveform display--based on C++: This time, I am going to go a little deeper. Just setting up the interface will not bring out the power of TouchGFX. Programming is still needed. Let's start with the last article. In the last article...; supermiao123 stm32/stm8

Shortcut: 00 01 02 03 04 05 06 07 08 09 0A 0C 0F 0J 0L 0M 0R 0S 0T 0Z 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 1H 1K 1M 1N 1P 1S 1T 1V 1X 1Z 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 2G 2K 2M 2N 2P 2Q 2R 2S 2T 2W 2Z 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 3G 3H 3J 3K 3L 3M 3N 3P 3R 3S 3T 3V 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4M 4N 4P 4S 4T 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5E 5G 5H 5K 5M 5N 5P 5S 5T 5V 60 61 62 63 64 65 66 67 68 69 6A 6C 6E 6F 6M 6N 6P 6R 6S 6T 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7M 7N 7P 7Q 7V 7W 7X 80 81 82 83 84 85 86 87 88 89 8A 8D 8E 8L 8N 8P 8S 8T 8W 8Y 8Z 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9F 9G 9H 9L 9S 9T 9W

Popular Components