# - Also rated for operation at 115Vac 400Hz. Self-heating will occur – evaluation in situ recommended
Ordering Information
Type
SF
Syfer Filter
Case Style
J
7.92mm A/F
Thread
E
¼-28
UNF
Electrical
configuration
C
C = C Filter
L = L-C Filter
Voltage
(dc)
500
050 = 50V
100 = 100V
200 = 200V
300 = 300V
500 = 500V
1K0 = 1kV
2K0 = 2kV
3K0 =3kV
Note: The addition of a 4-digit numerical suffix code can be used to denote changes to the standard part.
Options include for example: change of pin length / custom body dimensions or threads / alternative voltage rating / non-standard intermediate capacitance values / test
requirements.
Please refer specific requests to the factory.
Capacitance in
picofarads (pF)
0102
First digit is 0. Second and
third digits are significant
figures of capacitance code.
The fourth digit is the number
of zeros following.
Examples: 0101 = 100pF
0332 = 3300pF
Capacitance Tolerance
M
M =
20%
Dielectric
X
C = C0G/NP0
X = X7R
Hardware
0
0 = Without
1 = With
Syfer Technology Ltd.
SFJE Issue 2 (P108893) Release Date 04/03/14
Page 2 of 4
1GHz
24
27
30
34
38
41
44
48
51
54
57
60
63
66
68
70
Surface Mount and Panel Mount Solder-in filters
Solder pad layouts are included with the detailed information
for each part.
Recommended soldering profile
E01, E03, E07 SBSP ranges are compatible with all standard
solder types including lead-free, maximum temperature
260°C. For SBSG, SBSM and SFSS ranges, solder time should
be minimised, and the temperature controlled to a maximum
of 220°C. For SFSR, SFST and SFSU ranges the maximum
temperature is 250°C.
Cooling to ambient temperature should be allowed to occur
naturally. Natural cooling allows a gradual relaxation of
thermal mismatch stresses in the solder joints. Draughts
should be avoided. Forced air cooling can induce thermal
breakage, and cleaning with cold fluids immediately after a
soldering process may result in cracked filters.
Note: The use of FlexiCap™ terminations is strongly
recommended to reduce the risk of mechanical cracking.
Soldering to axial wire leads
Soldering temperature
The tip temperature of the iron should not exceed 300°C.
Dwell time
Soldering of filters
The soldering process should be controlled such that the filter
does not experience any thermal shocks which may induce
thermal cracks in the ceramic dielectric.
The pre-heat temperature rise of the filter should be kept to
around 2°C per second. In practice successful temperature
rises tend to be in the region of 1.5°C to 4°C per second
dependent upon substrate and components.
The introduction of a soak after pre-heat can be useful as it
allows temperature uniformity to be established across the
substrate thus preventing substrate warping. The magnitude
or direction of any warping may change on cooling imposing
damaging stresses upon the filter.
Dwell time should be 3-5 seconds maximum to minimise the
risk of cracking the capacitor due to thermal shock.
Heat sink
Where possible, a heat sink should be used between the solder
joint and the body, especially if longer dwell times are
required.
Bending or cropping of wire leads
Bending or cropping of the filter terminations should not be
carried out within 4mm (0.157”) of the epoxy encapsulation,
the wire should be supported when cropping.
Soldering irons should not be used for mounting surface
mount filters as they can result in thermal shock
damage to the chip capacitor.
A more comprehensive application note covering
installation of all Syfer products is available on the Syfer
京公网安备 11010802033920号
EEWORLD
