ALUMINUM ELECTROLYTIC CAPACITORS
ZT
4.5mmL Chip Type, Wide Temperature Range
series
Chip type with 4.5mm height, operating over wide temperature
range of – 40 ~ +105
°C
.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine using carrier tape.
Adapted to the RoHS directive (2002/95/EC).
WT
Smaller
ZT
Smaller
Specifications
Item
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
tan
δ
ZG
Performance Characteristics
– 40 ~ +105°C
6.3 ~ 50V
0.1 ~ 100µF
± 20% at 120Hz, 20°C
After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV or 3 (µA) , whichever is greater.
Measurement frequency : 120Hz, Temperature : 20°C
Rated voltage (V)
tan
δ
(MAX.)
6.3
0.38
10
0.32
6.3
6
10
16
0.20
10
5
10
Capacitance
change
25
0.16
16
3
6
35
0.14
25
3
6
35
3
4
50
0.14
50
3
4
Measurement frequency : 120Hz
Stability at Low Temperature
Rated voltage (V)
Z– 25°C / Z+20°C
Impedance ratio
Z– 40°C / Z+20°C
ZT / Z20 (MAX.)
Endurance
After 1000 hours' application of rated voltage
at 105°C, capacitors meet the characteristic
requirements listed at right.
Within ±25% of initial value (16V or less)
Within ±20% of initial value (25V or more)
tan
δ
300% or less of initial specified value
Leakage current
Initial specified value or less
Shelf Life
Resistance to soldering
heat
Marking
After storing the capacitors under no load at 105°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above.
The capacitors shall be kept on the hot plate maintained at 250°C
Capacitance change
Within ±10% of initial value
for 30 seconds. After removing from the hot plate and restored
tan
δ
Initial specified value or less
at room temperature, they meet the characteristic requirements
Initial specified value or less
Leakage current
listed at right.
Black print on the case top.
Chip Type
105°C Marking
Capacitance
Lot No.
Plastic platform
Voltage
0.3 MAX.
0.5 MAX.
C±0.2
Type numbering system (Example : 16V 10
µ
F)
Positive
1
2
3
4
5
6
7
8
9 10
11 12 13 14
U Z T 1 C 1 0 0 MC L 1 GB
Taping code
φD
4.5
+0.1
–0.2
A
B
C
E
4
1.8
4.3
4.3
1.0
(mm)
5 6.3
2.1 2.4
5.3 6.6
5.3 6.6
1.3 2.2
Configuration
Capacitance tolerance (±20%)
Rated Capacitance (10µF)
Rated voltage (16V)
Series name
Type
Voltage mark for 6.3V is 6V .
0.5 ~ 0.8
Negative
Dimensions
V
Cap. (µF)
Code
6.3
0J
10
1A
A±0.2 A
+
0.2
–
X2P
10
16V
φD±0.5
B±0.2
E
16
1C
25
1E
35
1V
4
4
4
4
4
4
4
5
6.3
50
1H
0.9
2.2
2.8
3.3
5.4
9.6
12
16
26
0.1
0.22
0.33
0.47
1
2.2
3.3
4.7
10
22
33
47
100
0R1
R22
R33
R47
010
2R2
3R3
4R7
100
220
330
470
101
4
5
5
6.3
19
26
32
52
5
5
6.3
24
30
40
4
5
6.3
6.3
16
26
35
44
4
5
6.3
6.3
11
20
33
42
4
5
6.3
13
22
36
Case size
φ
D (mm)
Rated
ripple
Rated Ripple (mArms) at 105°C 120Hz
Frequency coefficient of rated ripple current
Frequency
Coefficient
50 Hz
0.70
120 Hz
1.00
300 Hz
1.17
1 kHz
1.36
10 kHz~
1.50
Taping specifications are given in page 24.
Recommended land size, soldering by reflow are
given in page 25, 26.
Please select UX(p.74), UJ(p.76) series if high C/V
products are reqired.
Please refer to page 3 for the minimum order quantity.
CAT.8100V
京公网安备 11010802033920号
EEWORLD
